Installation Guide

Installation
1
Preparing the LED downlight
2
Preparing the installation
location
WARNING: Turn the power OFF at the
proceed with this installation.
Remove the existing trim and bulb,
revealing the existing socket.
Locate the socket in your existing
recessed housing and remove any
screws that prevent the socket
bracket from being removed.
3
Preparing the socket
Pull the socket assembly, including
the bracket, as low as possible
given the existing wire length
available. This may require socket
plate removal.
Remove any excess brackets from
the socket. Use care so as not to
damage wiring during this process.
WARNING: To prevent wiring
damage or abrasion, DO NOT expose
wiring to edges of sheet metal or other
sharp objects.
4
Installing the downlight
Attach the downlight to the
recessed housing socket. Plug
the base cable connector into the lamp.
5
Finishing the installation
WARNING: Make sure power to the
before attempting to remove the
packaging.
Compress the spring clips and insert into
the ears on inside of the recessed housing.
Carefully route the wires into the fixture.
Push the retrofit into the recessed housing
until the trim is flush with the ceiling
surface.
Questions, problems, missing parts? Before returning to the store,
call EcoSmart Customer Service
8 a.m.-7 p.m., EST, Monday-Friday
9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
If using a 6 inch housing, loosen the screws on the torsion spring brackets and
slide the brackets outward. Re-tighten screws to secure spring bracket in place.
THANK YOU
of this downlight. We strive to continually create quality products designed to enhance your
home. Visit us online to see our full line of products available for your home improvement
needs. Thank you for choosing EcoSmart!
USE AND CARE GUIDE
LED Recessed Downlight
Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. It may be necessary to remove a socket mounting plate for adequate clearance.
2. Each lampholder shall be installed only in its intended manner and orientation.
3. Not all existing recessed housings that meet these requirements will be compatible
with the downlight. To ensure compatibility, a test installation should be conducted.
4. This light is suitable for damp locations.
5. Do not make or alter any open holes in an enclosure of wiring or electrical
components during kit installation.
6. The minimum temperature rating for this light is 4°F or -20 °C.
7. This light is compatible with most dimmer switches when used with multiple
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
NOTE:
Pre-Installation
RECESSED HOUSING COMPATIBILITY
The EcoSmart LED downlight is designed to install in most standard 6 in. and some 5 in.
recessed downlight housings. For a list of compatible housings, go to www.homedepot.
com.
Compatibility of housings not on this list may be determined by measurement of the
housing as detailed in this drawing:
Diameter Range
Warranty
Item #1001 653 666
Model #DL-N34A11FR1-27
TOOLS REQUIRED
Phillips screwdriver
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
The limited warranty set forth below is given by The Home Depot (“Seller”) with respect to
the lighting product packaged with this limited warranty (the “Product”). Your Product, when
delivered to you in new condition in its original packaging, is warranted against defects in
materials or workmanship as follows: for a period of five (5) years from the date of original
purchase, defective parts or a defective Product returned to Seller, or its authorized service
providers, as applicable, and proven to be defective upon inspection, will be repaired, or
exchanged for a new Product, as determined by Seller, or the authorized service provider.
This limited warranty covers all defects encountered in normal use of the Product, and
does not apply in the following cases: Loss of or damage to the Product due to abuse,
maintenance or environmental instructions prescribed by Seller in writing or services
performed by someone other than Seller or its authorized service provider.
WARRANTY IS VOID IF PRODUCT IS NOT USED FOR THE PURPOSE FOR WHICH THIS PRODUCT
IS MANUFACTURED. Any complaints you may have regarding the product should be
addressed to the Customer Service Team at 1-877-527-0313.
NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, APPLIES TO THE PRODUCT AFTER THE APPLICABLE
PERIOD OF THE EXPRESS LIMITED WARRANTY STATED ABOVE, AND NO OTHER EXPRESS
WARRANTY OR GUARANTY GIVEN BY ANY PERSON OR ENTITY WITH RESPECT TO THE
PRODUCT SHALL BIND THE SELLER. (SOME STATES AND PROVINCES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.)
NOT INTENDED FOR USE WITH EMERGENCY EXIT FIXTURES OR EMERGENCY EXIT LIGHTS.
NOT FOR USE WHERE EXPOSED DIRECTLY TO THE WEATHER OR WATER. NOT FOR USE IN
TOTALLY ENCLOSED RECESSED FIXTURES.
Call 1-877-527-0313 to address issues with bulbs under warranty.
WARNING: Risk of Electric Shock. Disconnect power at the fuse or circuit breaker before installing
or servicing.
WARNING: Risk of fire or electric shock. Install this kit only in luminaires that have the
construction features and dimensions shown in the photographs and/or drawings and where the
input rating of the retrofit kit does not exceed the input rating of the luminaire.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal
or other sharp objects.
WARNING:
CAUTION: Risk of electrical shock. Do not open. There are no user serviceable parts inside. Turn
the power off before inspection, installation, or removal.
CAUTION: Use only on 120 VAC, 60 Hz circuits.
210*290mm
Model Input Volts(Vac) Input Frequency (Hz) Input Watts (W)
DL-N34A11FR1-27 120 60 10
0°
90°
±180°
-90°
-60°
-30°
60°
30°
-120°
-150°
120°
150°
77.05
154.09
231.14
308.19
385.23
C0/180,84.7
UNIT:cd
C90/270,83.1
AVERAGE BEAM ANGLE(50%):83.9 DEG