Installation Guide

Retain this manual for future use.
USE AND CARE GUIDE
16 FT SMART TUNABLE
TAPE LIGHT
Installation - Continued
Installation
Layout Considerations
A
B
4
Installing the controller cable
Clean the location in which the light strip (A) is to be mounted to make sure
it is free from dirt, dust, and oil, or anything that will inhibit the adhesive
from making solid contact with the mounting surface.
Connect the 6-terminal cable from the output of the controller cable (B) to the
6-pin end of the light strip.
Questions, problems, missing parts? Please call Hubspace Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday and 9 a.m. - 6 p.m., EST, Saturday
at [phone]
WWW.HOMEDEPOT.COM/HUBSPACE
Safety Information
Contact the Customer Service Team at [phone] or visit WWW.HOMEDPOT.COM/HUBSPACE.
Warranty
PACKAGE CONTENTS
2-YEARS LIMITED WARRANTY
Peel off the adhesive backing on the light strip (A), and secure the light strip (A) to
the desired location by pressing firmly for 30 seconds
Place the mounting clip (D) over the light strip and secure with mounting screws (E).
Care and Cleaning
Pre-Installation
Preparing the light strip (optional)
2
Installing the light strip
D
E
Lightly mark the desired starting location where the power adaptor with controller
cable (B) will connect to the tape. Make sure there is adequate room for the
tape light (A) and power adaptor with controller cable (B) in this space and that
the power adaptor can reach an appropriate power receptacle without being
pulled tightly.
Determine the desired location and length of the LED light strip needed for
installation. If any cuts are desired, follow “Preparing the light strip” below.
□
□
□
□
□
□
□
□
□
□
□
Before attempting to clean the light strip, unplug the adaptor from the power outlet.
To clean the light strip, use a clean, dry, or slightly damp cloth.
Allow the light strip and components to dry thoroughly before plugging the power
adaptor back into the outlet.
Do not use any cleaners with chemicals, solvents, or harsh abrasives, as damage
to the light strip may occur.
Item # 1005-864-272
Model # AL-TP-RGBCW-60-2116
IMPORTANT SAFETY INSTRUCTIONS
(SAVE THESE INSTRUCTIONS)
Read All Instructions
CAUTION: Do not operate light strip while coiled.
CAUTION: This product is rated for indoor,
damp locations only.
CAUTION: Do not install near or around
flammable or corrosive materials.
CAUTION: Do not subject flexible lighting to
continuous flexing.
CAUTION: To avoid damage to the light
strip, do not twist the light strip or bend past
the bend radius of 60 degrees.
CAUTION: This LED product is designed to be used only with the 24V DC power adaptor
included with the kit. Do not operate with any other power supply type. Disconnect power at
the source prior to attempting installation.
WARNING: Do not connect more than 32 feet
(2 pieces) of tape light strip to this single adaptor.
WARNING: Do not submerge the flexible light in
liquids or use the product in the vicinity of
standing water or other liquids.
WARNING: Do not secure this product with
staples, nails, or other sharp objects that may
damage the insulation.
WARNING: Do not cover this product as the
covering may cause the flexible light to
overheat and either melt or ignite.
WARNING: Do not use if there is any damage to
the light or cord insulation. Inspect periodically.
Connect the Smart Device
3
Linking the light strip
2 x 16 ft. lengths of light string can be linked together. Do not attempt to
connect more than 32 ft. to one power adaptor.
□
Connect the 6-terminal end from the output of the first tape light strip to the
6-pin start of the next tape light strip.
□
Plug the 24V DC power adaptor (B) into an appropriate 120V power outlet.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC Responsible Party: American Lighting Inc.
Address: 11775 E.45th Ave. Denver, CO 80239
Telephone Number: 1 800 880 1180
1
□
□
□
The manufacturer warrants this lighting fixture against defects in materials and
workmanship for a period of two years from the date of purchase. If within this period
the product is found to be defective in material or workmanship, the product must be
returned, with a copy of the bill of sale as proof of purchase, to the original place of
purchase. The manufacturer will, at its option, repair, replace, or refund the purchase
price to the original purchaser or consumer. This warranty does not cover light bulbs
or the fixture becoming damaged due to misuse, accidental damage, improper handling
and/or installation, and specifically excludes liability for direct, incidental, or
consequential damages. As some states do not allow exclusions or limitation on an
implied warranty, so the above exclusions and limitations may not apply. This warranty
gives you specific rights and you may also have other rights that vary from state to state.
The LED tape light (A) can be cut to a desired length; however, it can only be cut where
marked with scissors, approximately every 9.8 inches. Do not cut the silver color solder
marks; only in the center of the copper pads as shown.
To adjust the length, use the following steps:
Locate the cuttable locations on the tape light (A), starting from the end that has
the power supply wire attached.
Choose the location to be cut that best suits the length of tape light needed to
illuminate the desired area.
Let’s Get Started!
1
Using sharp scissors, cut directly through the center of the cut line. Be sure not
to cut off the 6-pin connection at the start of the tape.
Part Description
16 ft. LED Tape Light
Power Adaptor with Controller
B
A
C
Quantity
1
1
D
Handheld Remote Control
1
E
Mounting Clip
12
Mounting Screws
24
CAUTION: To avoid possible fire, product
damage, or early lamp failure, this tape light
should not be used in heat-producing appliances.
CAUTION: Do not route the cord or flexible light
cable through walls, doors, windows, or any
similar part of a building structure.
C
□
□
Download the Hubspace™ app from the App Store or the Google Play Store to
your mobile device.
Launch the app.
□
□
To register, enter your email address and a password. Or, log-in if you already
have an account.
Bluetooth access is required for device setup.
Verify Your Network
2
□
□
This Hubspace™ device requires a 2.4GHz Wi-Fi channel.
Most routers provide a 2.4GHz Wi-Fi channel.
□
□
Hubspace™ only shows Wi-Fi networks that your device can use.
If you do not see your Wi-Fi netowrk name when you attempt to connect your
device, please check your router settings.
Add a Device
3
□
□
In the Hubspace™ app, tap the plus sign in the upper right corner.
Scan your product’s QR code. You can find a copy of the QR code on the device
itself and in the Quick Start Guide.
i. Scan problem?
ii. If the QR code cannot be scanned for some reason, you can enter
the code manually. Tap Enter Code and follow the instructions.
Set up Your Voice Assistant
4
□
□
In the Hubspace™ app, tap the Hubspace button.
Select the Integrations tab, choose your voice assistant and follow the instructions.
□
Connect your device to power and follow the instructions on screen.
□
If you are unable to access the QR code for your light, you can put it into
discovery mode with the following sequence:
Switch the device OFF and ON 5 times. The light will pulse to show that it can
now be discovered. In the Hubspace™ app, tap the plus sign in the upper right
corner and follow the instructions to discover devices. More than one device
can be added at a time using this method.
Ensure surface is clean, sturdy, and mechanically sound.
□
Operation
Operating the remote
Troubleshooting
Problem Solution
The tape light does not turn on.
Ensure the power adaptor is plugged into a live 120V receptacle.
Check the connections and make sure the power adaptor wire is
securely connected to the copper connections of the tape light.
Aim the remote directly at the controller cable (B).
Remove the plastic tab from the back of the handheld remote (C).
Check to make sure the plastic tab has been removed from the
battery compartment on the back of the handheld remote control.
Check to make sure the polarity of the batteries is correct. Check to
make sure the batteries are not dead.
Check the line of sight and move the IR eye on the controller
accordingly. Make sure that the distance between the handheld
remote control and the IR eye on the driver is within 5 m (16.4 ft.)
□
□
When light is turned OFF, the controller (B) will remember the last setting.
□
Ensure the battery contacts are clean prior to battery installation.
□
Remove batteries from equipment when not in use for an extended period to time.
□
□
□
□
□
My Hubspace device is not
connecting to Wi-Fi.
Make sure your device is connected to a power source.
□
My device cannot find any Wi-Fi
networks.
Make sure you have a 2.4GHz capable Wi-Fi network within
range of the device you are trying to add.
□
I cannot find the QR code.
It is on the plug adaptor. A copy of the QR code is also included in
your device’s documentation.
□
The QR code has become damaged.
How do I add the device?
Under the QR code are numbers. You can enter those numbers
manually instead of scanning the code.
□
A device is on another account.
How do I transfer it?
Scan the QR code and it will transfer to your account.
□
My device is offline for long periods
of time.
Make sure your Wi-Fi signal strength is sufficient. You may need to
move your router, use mesh Wi-Fi, or Wi-Fi extenders.
□
The device is on an I scanned the
QR code, but the app cannot
connect to it.
Turn off Bluetooth on your phone and turn it back on. Then, scan
the QR code.
□
Can I scan the same QR code to
add multiple products?
No. Each product has a unique QR code.
□
My device is in a location that does
not have Wi-Fi. Can I still use it with
the Hubspace app?
Yes:
- Use the app on a phone with an Internet connection like LTE.
- The phone must be within Bluetooth range of your Hubspace device.
□
Your Internet connection or Wi-Fi network may be down. Check
your router and internet connection.
□
CAUTION: The remote control included utilizes a 3V CR2025 battery; Do not dispose of batteries
in fire as they may explode or leak. Please dispose of used batteries immediately and safely. Only
replace with the same battery type. Examine devices and make sure the battery compartment is
correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if
compartment is not secure.
WARNING: KEEP BATTERIES OUT OF THE REACH OF CHILDREN! BATTERIES ARE NOT A TOY! If swallowed,
they can cause severe injury or death within 2 hours. In case of swallowing, call emergency
services immediately. Tell others of the risks associated with button batteries to keep kids safe.
NOTE: The maximum operating distance,
with new batteries, between the handheld
remote (C) and the controller cable (B) is
approximately 5 m (16.4 ft.).
Button
Description
Functions options (jump, fade)
Turn OFF tape light
Turn ON tape light (last status)
Speed +/- adjust
More Color Options
ON/OFF, RGB LEDs
Red / Green / Blue
Yellow / Cyan / Violet
Brightness +/- adjust, RGB LEDs
6500K CCT Full ON
2200K CCT Full ON
6500K & 2200K CCTs Full ON
CCT Tuning, + Cool White
CCT Tuning, + Warm White
ON/OFF for White LEDs
Brightness +/- adjust, White LEDs
TM
TM
Correct
a≥60˚ a<60˚
Incorrect Incorrect