User Start Guide

ManualsBrandsEcoNet Controls ManualsHome AutomationEcoNet Controls Z-Wave Smart Water Valve Kit with one Leak Sensor, For 1/2', 3/4", 1" Valves

EVC200 Quick Start Guide

Specifications

• The EVC200 can be included with, and controlled, using any compatible Z-Wave controller. The EVC200 also acts as signal repeater for the Z-

Wave network, extending the Z-Wave transmission as part of the “mesh network”. The EVC200 is designed to work with a pre-installed

standard levered ball type water shut off valve. If your water shut off valve is not a levered type, consult a plumber to have your shut off

valve changed to a levered type.

• The EVC200 is designed to be installed onto an existing levered type ball valve as detailed below. Caution: If you do not have experience

installing and configuring EVC200 type devices, please consult a professional installer.

• Z-Wave Plus Certified

• Open/Closed toggle Button/Green LED indicator

• U.S. Standard Z-Wave Frequency

• Supported Valve Sizes: ½”, ¾”, 1" (Optional 1.25" and 1.5")

• Requires 12V DC/1amp power, AC Adapter Included

• Wireless Range: 30M (line of sight)

• Close/Open Time: ~ 18 seconds

• High Torque Geared Valve Motor: ~ 11lbf (~15Nm)

• Male 6 pin PS2 connector (cable 38"/980mm)

• Universal AC Adapter Included (cable length 48"/1230mm)

• Note: Requires Z-Wave Controller or Gateway

• Optional Plug-In Wired Leak Sensor

• Optional Output for second "slave" Valve Robot, see Condo Kits

• Optional Integrated Ball Valve

Including the EVC200 Z-Wave Automatic Valve with a Z-Wave Controller

Including or Adding the EVC200 to a Z-Wave Controller: Place the Z-Wave controller in inclusion (learning) mode. Press the Power button 3

or more times rapidly (within 0.5 seconds). Once the controller has acknowledged the inclusion, the EVC200 has been included in the Z-Wave

network with the controller. Exit the including mode and you should see the EVC200 Automatic Valve under your list of devices. Some devices

(like the Vera controller) require that you reload or refresh the controller so it polls, identifies, and configures the new device. Once the

configuration is complete, you can control the powered valve through your Z-Wave controller’s user interface. The valve supports Open or On

command and Closed or Off command through a standard Z-Wave controller. The valve can also be open or closed with a single push of the

power button on the unit, toggling from open to closed or closed to open. The valve can also be open/closed manually by hand by pushing

the clutch pin.

Excluding or Removing the EVC200 from a Z-Wave Controller: Place your Z-Wave controller in exclusion (un-learning) mode. Once the

controller is in exclusion mode, bring the EVC200 close to the Z-Wave controller (several feet) and press the Power button 3 or more times

rapidly (within 0.5 seconds). Once the controller has acknowledged the exclusion, the EVC200 has been cleared of any previous inclusions. (It

is recommended to keep the EVC200 within 1M/3ft of the controller when including or removing)

There can be a number of reasons that the EVC200 does not work with your controller. If the inclusion process does not work the first time,

repeat the process but try “excluding” first and then complete the “inclusion” process.

Motor Assembly

Control Module

Mounting Bracket

Silicone Tape

AC Adapter

(12V DC)

Valve Lever

pins

Pivot Point

Clutch Pin

Mounting Tab

Summary of content (3 pages)

PAGE 1
EVC200 Quick Start Guide Specifications • The EVC200 can be included with, and controlled, using any compatible Z-Wave controller. The EVC200 also acts as signal repeater for the ZWave network, extending the Z-Wave transmission as part of the “mesh network”. The EVC200 is designed to work with a pre-installed standard levered ball type water shut off valve. If your water shut off valve is not a levered type, consult a plumber to have your shut off valve changed to a levered type.
PAGE 2
Mechanical Installation: 1. The tape does not stick to the valve but sticks to itself With a slight stretch, tightly wrap Silicon tape around valve shoulder: Use one hand to hold the start of the tape against the valve shoulder while using your other hand to tightly wrap the tap around itself 2. Attach mounting bracket to motor assembly: Slide/push the HCx mounting bracket over the motor assembly tab. Insert M6 screw and adjust finger tight to allow left/right position adjustment 3.
PAGE 3
EVC200 Z-Wave Plus Commands: Z-Wave Network inclusion Putting your controller into inclusion mode (adding new devices). Press the Power button 3 or more times rapidly (within 1.5 seconds). It is recommended to keep the EVC200 within 1M/3ft of the controller. (Set controller to inclusion mode first) While waiting for inclusion/adding commands from controller, LED blinks 1 time per second.