Lite-Ex PL 30 Bedienungsanleitung · Operating Instructions Notice d‘utilisation · Gebruiksaanwijzing Istruzioni per l‘uso · Instrucciones de uso Manual de instruçoes · Bruksanvisning
Deutsch Seite 1 English Page 11 Français Page 21 Nederlands Pagina 31 Italiano Page .41 Español Página 51 Português Página 61 Svenska Sida .
Table of Contents Page 1. Application 12 2. Safety instructions 12 3. Errors and load restrictions 12 4. Safety regulations 12 4.1 Special requirements for use in ex-hazardous areas 13 5. Safety instructions 13 6. Ex-data 13 7. Technical data 14 8. Functional description / operating information 14 8.1 Lite-Ex PL 30 components 15 8.2 Getting started 15 8.3 Battery replacement 15 8.4 Cleaning the twist ring 16 8.5 Lamp replacement 16 8.6 Replacing the spare disc 16 9. Repairs 16 10.
1. Application The Lite-Ex PL 30 is an LED pocket torch designed for industrial applications or use in potentially explosive areas of Zones 2, 1 and 0 as well as 22, 21 and 20 in accordance with Directive 99/92/EC (ATEX 137). 2. Safety instructions These operating instructions contain information and safety regulations that must be followed to ensure safe and reliable operation of the unit under the described conditions.
The following additional safety regulations must also be observed: - The unit must not be opened within the Ex-area. - The batteries must only be changed outside the Ex-area. - Additional or spare batteries must not be carried in the Ex-area. - Only approved battery types may be used. - Only spare sealing rings and discs of ecom instruments are allowed. - Only accessories approved by ecom instruments GmbH may be used. - Prevent the unit from coming into contact with aggressive acidic or alkaline solutions.
7. Technical data Ambient temperature Ta: Storage temperature: Battery / power supply: Lamp: Operating time: Dimensions: Weight: IP rating: ESD protection: CE designation: -20 ... +50°C -30 ... +60°C (without batteries) 3 x LR14 (see table) 1 high-performance LED (3-watt) > 48 hours (continuous) approx. 220 mm x 40/45 mm approx. 550 g (including batteries) IP 65 Antistatic housing 0102 Table of approved battery types Manufacturer Type GP Super Alkaline Battery 14A LR14 Eveready Energizer No.
8.1 Lite-Ex PL 30 components Illustration 1 Body of torch Sealing rings Twist ring Battery compartment Housing head Alignment screw Torch head Spare disc 8.2 Getting started In order to be able to use the torch in the Ex-area, you must first check that the outer housing head and body are screwed on completely. After this has been done, you can switch on the torch by turning the yellow twist ring slightly in a clockwise direction. The torch is supplied with factory-fitted batteries. 8.
.4 Cleaning the twist ring A non-contacting twist ring is used to switch on the Lite-Ex PL 30 (see description above). Dirt or moisture does not effect the function. The twist ring is easy to clean if excessive amounts of dirt and grime have made it difficult to turn. First take off the torch body and remove the batteries (see section 8.3 Battery replacement). Remove the twist ring by sliding it off the back of the torch, and then clean the ring.
10. Cleaning, maintenance and storage - Only use a suitable cloth or sponge to clean the unit. Do not use solvents or abrasive cleaning agents to clean the unit. - We recommended having the operation and lumen output of the device checked by the manufacturer every two years. - The batteries should be taken out of the unit if it is to be stored for extended periods. - The storage temperature should be within the permitted range of -30°C to +60°C. 11.
12.
19
13. EC Declaration of Conformity Further details relating to the declaration of conformity can be found at the following Internet address: http://www.ecom-ex.com in the Product Download area.
Tel.: +49 (0) 62 94 / 42 24-0 Fax: +49 (0) 62 94 / 42 24-90 E-Mail: sales@ecom-ex.com Internet: www.ecom-ex.com 2055 AL 01 A00 12/05 Änderungen vorbehalten! Subject to change without notice! ecom instruments GmbH Industriestr.
