User's Manual

46 47
2 Choose Communications > 802.11 Radio > Funk.
3 Select the prole you want to congure.
4 For 8021x, choose LEAP.
5 For Association, choose Open, WPA, WPA2, or Network EAP. Encryption automatically
defaults to TKIP if you choose WPA, AES if you choose WPA2, and WEP if you choose
Open or Network EAP.
6 For Prompt for Credentials, choose Enter credentials now.
7 Enter a User Name and User Password.
8 Save your settings.
Configure Static WEP Security With Funk Security
Use the following procedure to congure static WEP security with Funk. ecom instruments recom-
mends that you use WPA2-PSK instead of WEP if possible.
1 Make sure the communications and radio parameters on your computer are congured.
2 Make sure Funk is selected as your security choice.
3 Start ecom instruments Settings.
4 Choose Communications > 802.11 Radio > Funk Security.
5 Select the prole you want to congure.
6 For Association, choose Open.
7 For Encryption, choose WEP.
8 For 8021x choose None.
9 Dene a value for the keys you want to use. You can dene up to four keys (Key 1 through
Key 4). Enter an ASCII key or a hex key that is either 5 bytes or 13 bytes long depending
on the capability of the radio. Set a 5- byte value for 64-bit WEP or a 13-byte value for
128-bit WEP. Hex keys must be preceded by 0x and contain 5 or 13 hex pairs.
10 For Transmit key, choose the key you want to use for transmitting data.
11 Save your settings.
Use Open (No Security) Associations with Funk
Use the following procedure to congure your mobile computer for open security using Funk.
1 Start ecom instruments Settings.
2 Choose Communications > 802.11 Radio > Funk Security.
3 Select the active prole you are using.
4 For Association, choose Open.
5 For Encryption, choose None.
6 Tap OK. Your settings are saved.
Select Microsoft as Your Security Choice
The default security setting is Funk. If you want to use Microsoft Wireless Zero Conguration (WZC)
security, you need to select it as your security choice. After you select Microsoft as your security
choice, you will be prompted to save your settings and reset the computer for your change to take
effect.
With Microsoft as your security choice, you can congure:
• WPA or WPA2
• 802.1x
• Static WEP
9 If you choose TLS:
a Load a user and root certicate on your computer. For help, see Load a Certicate”
on page 95.
b Enter a User Name and Subject Name.
c For Validate Server Certicate, choose Yes.
Configure WPA or WPA2 Personal (PSK) Security With Funk
Use the following procedure to congure WPA-PSK or WPA2-PSK with Funk security.
1 Make sure the communications and radio parameters on your computer are congured.
2 Make sure Funk is selected as your security choice.
3 Start ecom instruments Settings.
4 Choose Communications > 802.11 Radio > Funk Security.
5 Select the prole you want to congure.
6 For Association, choose WPA or WPA2.
7 For 8021x, choose None.
8 For Pre-Shared Key, enter the pre-shared key or passphrase. The pre-shared key must be
a value of 32 hex pairs preceded by 0x for a total of 66 characters. The value must match
the key value on the access point. The passphrase must be from 8 to 63 characters. After
you enter a passphrase, the i.roc® Ci70 -Ex internally converts it to a pre-shared key. This
value must match the passphrase on the authenticator.
9 Save your settings.
Configure 802�1x Security With Funk Security
Use the following procedure to congure 802.1x-WEP security with Funk security. ecom instru-
ments recommends that you use WPA2-802.1x instead of 802.1x-WEP if possible.
1 Make sure the communications and radio parameters on your computer are congured.
2 Make sure Funk is selected as your security choice.
3 Start ecom instruments Settings.
4 Choose Communications > 802.11 Radio > Funk Security.
5 Select the prole you want to congure.
6 For Association, choose Open.
7 For Encryption, choose WEP.
8 For 8021x, choose TTLS, PEAP, or TLS.
9 If you chose TTLS or PEAP:
a Enter a User Name.
b For Prompt for Credentials, choose Enter credentials now.
c Enter a User Password.
d For Validate Server Certicate, choose Yes.
10 If you choose TLS:
a Load a user and root certicate on your computer. For help, see Load a Certicate”
on page 95.
b For Validate Server Certicate, choose Yes.
c Enter a User Name and Subject Name.
11 Save your settings.
Configure LEAP Security With Funk
After you congure the communications and radio parameters on your mobile computer and select
Funk as your security choice, you can congure LEAP.
1 Start ecom instruments Settings.