Certification Exhibit FCC ID: Z9O-FAS1521 IC: 10060A-FAS1521 FCC Rule Part: 15.231 IC Radio Standards Specification: RSS-210 ACS Project: 14-2067 Manufacturer: UltraClenz, LLC Models: FAS1521-01 User Manual (Part 2 of 2) 3998 FAU Blvd.
DFU Document Title Here UltraClenz, LLC 4. Power-On On Self Test Sequence When batteries are installed in the PSS Door Monitor Monitor,, a power on self test sequence initiates as follows: single flash green LED, single flash red LED, single flash green LED, single flash red LED, and three audible alarm beeps. 5.
DFU Document Title Here UltraClenz, LLC Figure 7. Left Side PIR PIR Sensor Connector Figure 8. PIR Connector 8. PIR Sensor Alignment The sensor alignment is adjusted by loosening the 1/8” hex screw above the PIR window and by rotating the turret with the adjustment tab at the bottom of the PIR sensor window window. It must be positioned so that the PIR window is aimed across the room’s door frame or entry path. (See Figures 9 and 10) Figure 9.
DFU Document Title Here UltraClenz, LLC Figure 10. PIR Sensor Alignment Tab 9. Door Mounting Location The PSS Door Monitor can be mounted on the wall outside or inside and left or right side of the patient room’s door opening. The mounting location of the PSS Door Monitor can be at approximately the same height as the hand dispenser mounting height and horizontal mounting is 2 to 3 inches from entry path.
DFU Document Title Here UltraClenz, LLC Appendix A - USB to RS485 Converter Installation Introduction The USB to RS485 Converter allows the connection of Windows PC based application software to an UltraClenz RS-485 enabled device. The USB to RS485 Converter connects directly to the host PC’s USB port via an A-B USB cable. Power for this device is provided by the PC’s USB port so no external power source is required.
DFU Document Title Here UltraClenz, LLC Configuration The USB to RS485 Converter will emulate a serial (COM) port on the host PC. It will be necessary to determine which COM port the USB driver has selected. To do this, follow the steps below. 1. Open the Control Panel 2. Click on Performance and Maintenance (only if Control Panel is setup for Category View) 3. Click on System 4. Click on the Hardware tab 5. Click the Device Manager button 6. Select View -> Devices by Type from the menu 7.
DFU Document Title Here UltraClenz, LLC Appendix B - Windows Compatibility Mode UltraClenz PC application software is currently developed under Windows XP. For it to perform correctly under newer versions of Windows, Windows Compatibility Mode must be enabled after the software has been installed. Once compatibility mode has been enabled, nothing more is required. The software will automatically run in compatibility mode each time it is launched.
DFU Document Title Here UltraClenz, LLC Appendix C - COM Port Performance If communication performance issues are observed, it will be necessary to “tweak” the COM port’s properties. The following steps will configure the COM port for reliable communications. 1. Connect the USB to RS485 Converter to an available USB port. Then, go to Device Manager, expand “Ports” and double click “USB Serial Port”. 2. In USB Serial Port Properties, select the “Port Settings” tab and click the “Advanced” button.
DFU Document Title Here UltraClenz, LLC 3. In Advanced Settings, change “Latency Timer” to 1. Change both “Minimum Read Timeout” and “Minimum Write Timeout” to 200. Then click the “OK” button. 4. For COM port changes to take effect, Windows 7 and 8 may require a reboot (Windows XP does not).
DFU Document Title Here UltraClenz, LLC Appendix D - Certification and Safety Approvals FCC Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
DFU Document Title Here UltraClenz, LLC Appendix E - Warranty This device is warranted against defective materials and workmanship for two years from the date of purchase. Equipment covered by this warranty will be repaired or replaced in the United States and Canada, WITHOUT CHARGE, except for shipping and handling, by our Factory Service Center.
