WATERTIGHT SEAL FOR ECOFASTEN BRACKETS INSTALLATION GUIDE REVISION: 11/05/21 VERSION: V2.1 ECOFASTENSOLAR.
REVISION: 11/05/21 VERSION: V2.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL SIMPLESEAL SimpleSeal was designed for installation on most metal roofs. The system utilizes a cone-shaped EPDM rubber bushing that fits into the countersink found on the underside of any EcoFasten compression bracket. When fastened to the roof, engaging a purlin or rafter, the SimpleSeal bushing is compressed inside the bracket, creating a watertight seal.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL INSTALLATION GUIDE SYSTEM COMPONENTS 1 3 4 1. 5/16" LAG BOLT COMPONENTS 2 3. 5/16" EPDM BONDED WASHER (AVAILABLE IN 3” AND 4”) 2. L-FOOT SCL-101 ML 3" 4.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL INSTALLATION GUIDE Pre-install the cone-shaped rubber SimpleSeal EPDM bushing into an EcoFasten compression bracket of your choice prior to installation by inserting the tip of the cone into the corresponding shape in the bottom of the compression bracket. The ridge around the tip of the cone will hold the bushing in place until the bracket is installed.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL INSTALLATION GUIDE Thread the 5/16" EPDM bonded sealing washer onto the 5/16" lag bolt and insert the bolt into the top of SimpleSeal EPDM bushing. Tighten fastener until bracket is pulled down snug to the roof surface. The tension required will vary with the project roof deck, age, and type. Be sure not to over tighten the fasteners and strip the threads.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL INSTALLATION GUIDE CUT SHEET: SIMPLESEAL EPDM BUSHING (50) 5 4 PART NUMBER DESCRIPTION QTY. REV. 1 350011 SIMPLE SEAL 1 01 3 1 2 REVISIONS DESCRIPTION REV. A NEW RELEASE (ECO #725) DATE APPROVED 04/15/2021 SO/JPS D D C C 1 B B THIRD ANGLE PROJECTION A DRAWN CHECKED ENG APPR. MFG APPR. Q.A. DO NOT SCALE DRAWING PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ESDEC INC.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL INSTALLATION GUIDE CUT SHEET: L-FOOT L-102 BLK 3” 5 3 4 PART NUMBER DESCRIPTION QTY. REV. 1 450050-01 L-102-3 ANOD BLK 1 01 2 150009-08 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG 1 01 3 150011-03 SS SERRATED FLANGE LOCK NUT, 3/8-16 1 02 1 2 REVISIONS DESCRIPTION REV. A RELEASE TO ESDEC FORMAT (ECO#723) DATE 04/02/2021 APPROVED RAD/JPS D D 1 3 C C 3.00 76.2 2 B B 1.88 47.6 1.92 48.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL INSTALLATION GUIDE CUT SHEET: L-FOOT L-102 MLL 6” 5 3 4 PART NUMBER DESCRIPTION QTY. REV. 1 450082-02 L-102-6 1 01 2 150009-08 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG 1 01 3 150011-03 SS SERRATED FLANGE LOCK NUT, 3/8-16 1 02 1 2 REVISIONS DESCRIPTION REV. A RELEASE TO ESDEC FORMAT (ECO #722) DATE APPROVED 04/05/2021 RAD/JPS D D 1 C C 6.00 152.4 3 2 B B 2.00 50.8 3.00 76.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL INSTALLATION GUIDE CUT SHEET: L-FOOT SCL-101 MLL/BLK 3” 5 3 4 PART NUMBER DESCRIPTION QTY. REV. 1 450049-02 L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL MLL 1 01 2 150009-08 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG 1 01 3 150011-03 SS SERRATED FLANGE LOCK NUT, 3/8-16 1 02 1 2 REVISIONS DESCRIPTION REV. A NEW RELEASE TO ESDEC FORMAT (ECO #748) DATE APPROVED 04/05/2021 RAD/JPS D D 1 C C 3.0 76.2 B B 1.88 47.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL INSTALLATION GUIDE CUT SHEET: CF UNIV L-FOOT MLL 3” - 2012022 5 3 4 PART NUMBER DESCRIPTION QTY. REV. 1 750120 CLICKFIT L FOOT ASSEMBLY 1 A 1 2 REVISIONS DESCRIPTION REV. A NEW RELEASE TO ESDEC FORMAT (ECO #760) DATE APPROVED 05/27/2021 RAD/JPS D D 1 C C 2.76 70.1 B B THIRD ANGLE PROJECTION A DRAWN CHECKED ENG APPR. MFG APPR. Q.A.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL INSTALLATION GUIDE SYSTEM COMPONENTS 1. Sim Seal Bushing: Consists of (1) EPDM Rubbber cone-shaped bushing. Aluminum Compression Bracket: Compatible with a variety of EcoFasten compression brackets. EcoFasten compression brackets are made out 6000 series aluminum with options available for mill or black finishes depending on the bracket. 3. Recommended Fasteners 5/16"x4" lag bolts. 4.
REVISION: 11/05/21 VERSION: V2.1 SIMPLESEAL DESIGN REQUIREMENTS 1. Bracket spacing to be recommended by project engineer. 2. Fasten attachment to roof using 1 5/16" lag bolt. 3. It is important to design new structures or assess existing structures to make sure they withstand retained loads. EXAMINATION 1. Substrate: Inspect structure on which brackets are to be installed and verify that it will withstand any additional loading that may be incurred. 2.
