R by FUJITSU TEN MODEL 54420 ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote OWNER'S MANUAL We appreciate your purchase of this receiver. Please read through this manual for correct operation. We suggest that after reading it you keep this manual in a safe place for future reference.
For your safety in using the 54420 Warnings and caution signs, illustrated below, are posted throughout this manual as well as on the 54420. They show safe and correct ways to handle the product so as to prevent personal injury to you and others and avoid damage to property. Before reading through the manual, take time to read through and learn the important information listed in this section.
Warning • Do not place the vinyl storage bag over a person. It may cause a serious accident or death by suffocation. • Do not adjust the controls while driving the car. To adjust the controls, stop the car in a safe location. • To prevent accidents, store batteries for the remote control out of the reach of small children.In case a child swallows a battery, consult a physician immediately. • Do not disassemble or rebuild this product. Doing so may cause an accident, fire or electrical shock.
Caution 4 • Do not stick your fingers or hands into the disc slot. Doing so may cause personal injury. • This product must be operated only as on-board equipment, or it may cause electrical shock or injury. • Do not play distorted sounds for long periods of time; the speakers may overheat and cause a fire. • This product uses an invisible laser light. In case a problem develops, be sure to consult the dealer from whom you purchased the product.
Table of Contents Operating Precautions ................................................ 8 Notes on Operation ........................................................................ 8 About compact discs .................................................................... 9 About cleaning a CD ................................................................... 11 Names of controls and parts .................................... 12 ESN (Key CD) Security Operating Procedure ..........
How to operate the tuner .......................................... 31 Tuning to a station ....................................................................... 31 Entering stations into memory automatically (The automatic preset mode: ASM) ............................................. 32 Manually setting stations into memory ......................................... 33 Preset station scan ...................................................................... 34 Switching the display .....................
If you have a question: .............................................. 60 Displaying information (for troubleshooting) .................................. 61 Specifications ............................................................ 64 Before installation .......................................................66 Components ............................................................................... 66 Setting the system-selector switch ..............................................
Operating precautions ٟ Operating Precautions Notes on Operation • For your safety, play only at volume levels that allow outside sounds to be heard. • Use only audio compact discs. This player can only play compact discs bearing the logo shown to the left. • Do not insert anything other than a CD into the disc slot. Do not insert any foreign objects, such as coins or credit cards, into the disc slot.
Operating precautions About compact discs • The signal recorded on a compact disc is read by a laser beam, so nothing touches the disc surface. A scratch on the recorded surface or a badly warped disc may cause deteriorated sound quality or intermittent playback. Observe the following precautions to ensure high quality sound performance: • Do not leave an ejected disc in the disc slot for very long; the disc may warp. Discs should be stored in their cases and kept away from high temperature and humidity.
Operating precautions About brand new CDs • You may notice that some brand new discs are rough around the center hole or outside edge. Remove the rough edges with the side of a ballpoint pen, etc. Rough edges may prevent proper loading in the deck. Flakes from the rough edges may also stick to the recorded surface and interfere with playback. About CD accessories • Do not use accessories (stabilizers, protective seals, laser lens cleaners, etc.) sold for “ improving sound performance” or “ protecting CDs.
Operating precautions About irregularly-shaped CDs • Specially-shaped CDs, like heartshaped or octagonal CDs, cannot be played. Do not attempt to play them, even with an adapter, since they may damage the player. About cleaning a CD • Use a commercially available compact disc cleaner to clean a CD, wiping lightly from the center to the edge. XXXX XXXX XXXX • Do not use benzine, thinner, LP record spray or other cleaners on CDs. They may damage a CD’s finish.
Names of controls and parts ٟ Names of controls and parts Front View [ （EJECT）] button [ASM] button [E-COM] button※ [CD] button [ DISC ] buttons [FM･AM] button [AUDIO CONTROL] button [DISP] button [PWR] button Buttons [1] to [6] [FUNC] button [ ] buttons ※NOTE：Double function button→"E-COM"&"MUTE" functions 12
ESN (Key CD) security operating procedure [PWR] button [FM･AM] button Button [1] ٟ ESN (Key CD) security operating procedure عHow to program the Key CD 1 . Turn the vehicle’s ignition on. Press the [PWR] button or [FM• AM] button to activate the tuner mode. The tuner is now turned on. 2 . Press and hold button [1], then the [FM• AM] button, and hold both for more than one second. A [SEC] message appears, then in two seconds it will change to [DISC].
ESN (Key CD) security operating procedure [PWR] button [FM･AM] button Button [1] • If there is a problem with the inserted CD, an [ERR] message will appear for two seconds and the CD will be ejected. Reinsert the ejected CD. • If a CD causes the [ERR] message to appear twice in a row, a [CHANGE] message will appear for two seconds. Try another CD. • The Security indicator will flash whenever the vehicle’s ignition is switched off. عHow to cancel the Key CD 1 . Turn the vehicle’s ignition on.
ESN (Key CD) security operating procedure • This process cancels the protection for the ESN deck. • If power to the 54420 is disconnected, then reconnected, a key CD will not need to be inserted in order to return the unit to normal operation. • Inserting a CD other than the Key CD will not cancel the protection. Instead, the display will show [ERR] for two seconds, then the normal CD playback mode will activate. عHow to change the Key CD 1 . First, cancel the existing Key CD.
ESN (Key CD) security operating procedure عHow to resume normal operation (ESN security lock out) If power to the 54420 is disconnected while ESN security is active (a Key CD was programmed), operation is disabled until power is restored and the unit unlocked. Follow this procedure to resume normal operation. 1 . When the power is turned on after disconnecting the battery power, a [SEC] message will appear for two seconds.
ESN (Key CD) security operating procedure عWhat happens if an incorrect CD is inserted? 1 . An [ERR_] message will be appear, then change to a flashing [DISC], then the CD will be ejected. You will have five uninterrupted attempts to insert the correct CD. 2 . After the 5 incorrect attempt, the display reads [CALL800] and the security indicator th lights steadily. • Number of errors: Numbers indicated at _ show the number of errors that occurred.
ESN (key CD) security operating procedure [DISP] button [FM･AM] button [PWR] button Button [4] عHow to turn the Security indicator on/off Once ESN security is activated, the indicator flashes whenever the vehicle’s ignition is turned off, warning potential thieves that the unit is protected. However, if you do not want this visible deterrent, it may be turned off. 1 . button, With the tuner mode ON, press the [DISP] then [FM• AM] button and hold both for more than a second. 2 .
Basic operation [CD] button [FM･AM] button Buttons [1] to [6] [PWR] button [ ] buttons ٟ Basic operation This section covers basic operating procedures.For additional details, please refer to the sections on specific functions. عTurning the power on and off 1 . Press the [PWR] button. Pressing the button turns the power on and off.
Basic operation عListening to the tuner 1 . Press the [FM• AM] button. This will turn the tuner on. To turn the tuner off, either press the [PWR] button or select another mode. 2 . Tap the [FM• AM] button to switch to the desired FM or AM bands. Each additional tap of the button switches the preset station sets from FM1 to FM2, FM3, then AM in sequence. 3 . Press the [ ] button to tune to a station.
Basic operation [E-COM] button [DISP] button [AUDIO CONTROL] button Button [6] [FUNC] button عAdjusting audio volume 1 . Turn the [AUDIO CONTROL] button to the left or right. Turn to the left : Decreases the volume. Turn to the right : Increases the volume. • Press and hold the [E-COM] button for more than two seconds to activate or cancel MUTE function. Warning Do not adjust the volume or other controls while driving the vehicle. Do so only while parked in a safe location.
Basic operation عOthers ٕ Disabling the guide tone feature (for button operation) The receiver is set at the factory to emit a beep tone in response to button operation. The guide tone feature may be disabled in the following procedure: 1 . Press and release the [FUNC] button. 2. Press and hold button[6] until the [BEEP OFF] display appears on the screen. Pressing the button will switch modes between the [BEEP ON] and the [BEEP OFF]. 3. Press the [FUNC] button again.
Basic operation [DISP] button [AUDIO CONTROL] button Buttons [1] to [5] ٕ Setting the clock This receiver uses the 12-hour, A.M./P.M.display notation. 1 . Press the [DISP] button repeatedly to switch to the clock display mode. 2 . To adjust the hour, press either button [1] or [2] while holding the [DISP] button down. Button [1]: Turns the hour back. Button [2]: Turns the hour forward. 3 . To adjust the minutes, press either button [3] or [4] while holding the [DISP] button down.
Basic operation ٕ Switching audio control modes Various audio control modes may be fine-tuned using this procedure. 1 . Press the [AUDIO CONTROL] button for less than one second. Pressing the button repeatedly will allow you to control adjustments of [BASS] (low frequencies), [TREB] (high frequencies), [FADER] (front-rear speaker balance), [BAL] (left-right speaker balance), and [SUB-W] (subwoofer level). 2 .
Basic operation [E-COM] button [DISP] button Button [5] [ASM] button [FUNC] button ٕSwitching Non-Fader modes 1 . Press the [FUNC] button. 2 . Press button [5] to switch the phase. 3 . Press the [FUNC] button. Pressing the button will cancel Function mode. ٕ Disabling the Tone Control Cancel feature 1 . Press the [FUNC] button. 2 . Press the [ASM] button to switch on or off. 3 . Press the [FUNC] button. Pressing the button will cancel Function mode. ٕ Disabling the display 1 . Press the [FUNC] button.
How to operate the CD player [CD] button ٟ How to operate the CD player First press the [CD] button to switch to the disc mode. It is assumed here that a CD has already been loaded into the unit. عListening to CDs 1 . Press the [CD] button. This turns on the disc mode and starts CD play. If an external CD changer is connected, each additional tap of the button will switch modes from CD changer 1 CD changer 2 CD player. A changer or player with no discs loaded will be skipped.
How to operate the CD player Button [4] [ ] buttons عAdvancing to the next track or returning to the beginning of the track being played 1 . Press the [ [ [ ] button. ] button: Advances to the next track. ] button: Returns to the beginning of the track being played. • Pressing and holding the [ ] button will fast-forward through a track, while pressing the [ ] button will fastreverse. عPlaying the beginning of tracks (SCAN) 1 . Press button [4 (SCAN)].
How to operate the CD player [DISP] button Buttons [5] to [6] عRepeating the same track (REPEAT) 1 . Press button [5 (RPT)] to repeat the track being played. To cancel, press button [5] again. عPlaying tracks in random order (RANDOM) 1 . Press button [6 (RAND)] to play the tracks in random order. To cancel, press button [6] again. • Occasionally the same track happens to be played (selected) two or more times in a row; this is normal operation and is no sign of a problem.
How to operate the CD player [ （EJECT）] button عEjecting the disc 1 . Press the [ （EJECT）] button.
How to operate the CD player [DISP]button Button [1] عDisplaying a genre for a CDs A preset genre can be assigned to individual CD and displayed when they are played. 1 . Press the [DISP] button until a preset genre is displayed. 2 . Press button [1] Nine genre are available for a CD in the following sequence; 1.JAZZ 2.POPS 3.ROCK 4.FUSION 5.BALLAD 6.GUEST 7.FAVORITE 8.BRANDNEW 9.DELETE When the [DELETE] is selected, the genre will not be displayed. عSwitching the display 1 .
How to operate the tuner [FM･AM] button [ ] buttons ٟ How to operate the tuner First, press the [FM• AM] button to start tuner operation. There are automatic and manual methods for setting stations in memory. The receiver will accept up to 24 stations in memory: six in AM and 18 in FM (6 each for FM1, FM2 and FM3.) عTuning to a station 1 . Tap the [FM• AM] button to switch to the desired FM or AM mode. Each tap will switch modes from FM1 → FM2 → FM3 → AM. 2 .
How to operate the tuner [ASM] button [FM･AM] button • At times, it may be difficult to maintain optimum reception because the antenna affixed to your vehicle is in motion constantly (relative to the broadcast antenna), encountering continuous variation in the received radio signals’ strength. Other factors affecting reception include interference from natural obstacles, sign posts, etc. عEntering stations into memory automatically (The automatic preset mode: ASM) 1 .
How to operate the tuner [FM･AM] button Buttons [1] to [6] [ ] buttons • Press any numbered button to select the station whose frequency is indicated right above the button. • When a new station is set in memory, the station previously set in memory will be deleted. • If the number of receivable stations fewer than six, the stations set in the rest of the preset buttons will be retained.
How to operate the tuner [ASM] button [DISP] button عPreset station scan This function enables reception of all the stations in the numbered preset buttons for five seconds each. 1 . Press the [ASM] button. [P• SCAN] will appear at the top of the display, and stations stored under preset buttons [1] through [6] will beplayed for five seconds each. 2 . Topressstopthethe[ASM] scan mode at a desired station, button again. The receiver will stay tuned to the desired station.
How to operate the tuner عFM reception characteristics In general, FM has much better tonal quality than AM. However, FM and FM stereo reception encounter several characteristic problems not encountered with AM. FM is more difficult to receive than AM in a moving vehicle. The following are explanatory notes on what to expect from FM reception and on how to get satisfactory performance. 1 . FM RECEPTION DIFFERS FROM AM A characteristic of transmitted signals is that lower frequencies travel further.
How to operate the tuner 3 . RECEPTION AREA OF FM BROADCASTS A home receiver can catch weak FM stereo signals through the use of a tall, directional or ultra-sensitive antenna. In a moving vehicle, the area for good reception is limited because of varying conditions encountered while driving, including the types and heights of broadcast antenna structures, signal strength, engine noise, etc. For best reception with manual antennae, extend the antenna mast as far as possible.
How to operate the tuner 4 . MULTIPATH The reflection characteristics of FM waves cause another problem called multipath– FM wave signals reflecting off of buildings, mountains, etc. When the antenna receives direct and reflected waves at the same time, distortion of sound in the treble range often occurs, such as static or a harsh-sounding voices. THIS IS NOT A TUNER PROBLEM. Only moving to another area with a clearer signal path can remedy the situation.
How to use the Card remote control ٟ How to use the Card remote control Precautions in use of the remote control • Be careful when handling the control, especially because it is small and light. Dropping or striking it hard may damage it, wear out the battery or cause a malfunction. • Keep the remote control free of moisture, dust and water. Do not subject it to shock. • Do not place the remote control unit where it will get hot, such as on the dashboard or near a heater vent.
How to use the Card remote control [MODE] button Remote-control light receptor [PWR] button [MUTE] button [+] button [ - ] button عTurning the power on/off 1 . Press the [PWR] button. The power turns on or off each time the button is pressed. • When the main unit is shut down, the remote control will not work. عAdjusting the audio volume 1 . Press the [+] or [-] button. [+] button: Increases the volume. [ -] button: Decreases the volume.
How to use the Card remote control [BAND] button [ TUNE･SEEK ] buttons [ PRESET CH ] buttons عHow to play the tuner Enter the tuner mode first. ٕ Select the FM/AM band 1. Tap the [BAND] button. Each tap will switch tuner modes from FM1 → FM2 → FM3 → AM. ٕ Select a station (manually or automatically) A short tap of the button will allow manual station tuning. Pressing for more than one second will start automatic tuning. 1. Press the [ TUNE• SEEK ] button.
How to use the Card remote control [BAND] button [ TRACK･APS ] buttons [ DISC ] buttons عHow to play CDs Select the disc mode first. ٕ Advancing to the next track or returning to the beginning of the track being played 1. Press the [ TRACK• APS ] button. [ ] button: Skips to the next track. [ ] button: Returns to the beginning of the track being played. • Hold the [ ] button down to fast-forward, or the [ button to fast-reverse the track being played. ] ٕ Skipping to the next or previous CD.
How to use the Card remote control عReplacing the battery Warning To prevent accidents, store the batteries out of the reach of children. If a child has swallowed one, consult a doctor immediately. Use one CR2025 battery. 1 . On the back of the remote control, while pressing the locking knob on the battery slot cover toward your right, pull out the battery carier with your fingernail. UNLOCK 2 . Remove the old battery, then place the new one in the carrier with the (+) mark facing up. 3 .
How to use an optional NOB remote control [AUDIO CONTROL] button Remote-control light receptor [MUTE] button [PWR] button ٟ How to use an optional NOB remote control عTurning the power on/off 1 . Press the [PWR] button. The power turns on or off each time the button is pressed. • When the main unit is shut down, the remote control will not work. عAdjusting the audio volume 1 . Press the [AUDIO CONTROL] button, and turn it to the left or right. Turn to the right: Increases the volume.
[BAND] button [ TUNE . SEEK ] buttons H-M US O DE P How to use an optional NOB remote control BAND MODE [MODE] button ޓ TRACK TUNE SEEK DISC E-COM MUTE PWR ILLUMI عSwitching playback modes 1 . Press the [MODE] button. Tap the button to switch modes in the following sequence: عHow to play the tuner Enter the tuner mode first. ٕ Select the FM/AM band 1. Tap the [BAND] button. Each tap will switch tuner modes from FM1 → FM2 → FM3 → AM.
H-M US O DE P How to use an optional NOB remote control BAND [ TRACK ] buttons MODE ޓ TRACK TUNE SEEK DISC [ E-COM MUTE DISC ] buttons PWR ILLUMI ٕ Selecting preset stations A total of six stations may be selected (preset tuning) out of those already set in memory through the main unit. (Refer to “Manually setting stations into memory,” page 33.) 1. Press the [ DISC ] button. [ ] button: Tunes the next preset number at a higher frequency.
How to use an optional NOB remote control H-M US O DE P (previous) disc. [BAND] button BAND MODE ޓ TRACK TUNE SEEK DISC [E-COM] button E-COM MUTE PWR [ILLUMI] button ILLUMI ٕ Switching disc modes 1. Press the [BAND] button. When the CD changer is connected, tap the [BAND] button to change modes from CD player → CD changer 1 → CD changer 2. The indicator will skip a changer or player that has no disc loaded in it.
How to use an optional NOB remote control عReplacing the battery Warning To prevent accidents, store the batteries out of the reach of children. If a child has swallowed one, consult a doctor immediately. Use two AA cell batteries. 1 . Remove the back cover of the remote control unit by gently pressing and sliding it in the direction indicated by the arrow. 2 . Install the two batterles provided into the compartment as illustrated inside the compartment. 3 .
How to use an optional NOB remote control ● Caution ● ・Be extremely careful not to swallow the battery. ・The battery life is approximately one year. If the remote control unit does not operate correctly or if the button lump gets dim, replace the batteries. ・Be sure to orlent the batteries correctly so that the positive and negative poles match the diagram. ・Do not use one new battery and one old one; use two new batteries.. ・Use only two of the same kind of battery.
How to operate the receiver with an optional CD changer connected [CD] button [ ] buttons ٟ How to operate the receiver with an optional CD changer connected عBasic operation This section covers the operation of the CD changer that is connected to the receiver. To switch from another mode, press the [CD] button. ٕ Listening to a CD 1. Press the [CD] button Each press of the button switches the mode from CD Player → CD Changer 1 → CD Changer 2.
How to operate the receiver with an optional CD changer connected Buttons [4] to [6] ٕPlaying the beginning of tracks (SCAN): 1. Press button [4 (SCAN)]. Tapping the button causes the changer to move up to the next track and play it for 10 seconds, then move up to the next track and play it for 10 seconds, and so on, on one CD, until the button is tapped again. Hold the button until the [ALL SCAN] display appears to play the first 10 seconds of the first track of every CD loaded.
How to operate the receiver with an optional CD changer connected [ASM] button [ ] buttons DISC Buttons [1] to [6] • Occasionally the same track happens to be played (selected) two or more times in a row, but it is no sign of a problem.
How to operate the receiver with an optional CD changer connected [DISP] button Button[1] عDisplaying a genre for a CDs A preset genre can be assigned to individual CD and displayed when they are played. 1 . Press the [DISP] button until a preset genre is displayed. 2 . Press button [1] Nine genre are available for a CD in the following sequence; 1.JAZZ 2.POPS 3.ROCK 4.FUSION 5.BALLAD 6.GUEST 7.FAVORITE 8.BRANDNEW 9.DELETE When the [DELETE] is selected, the genre will not be displayed.
How to operate the receiver with an optional DSP/EQ unit connected Button [1] [FUNC] button ٟ How to operate the receiver with an optional DSP/EQ unit connected عHow to operate the DSP functions The DSP feature adds reverberations to simulate ambience in different types of surroundings (room sizes). 1 . After pressing the [FUNC] button, tap button [1]. Each tap of the button [1] will switch the room size. ٕ Switching room sizes. 1. Tap button [1] to switch room sizes.
How to operate the receiver with an optional DSP/EQ unit connected Button [1] [FUNC] button • The following six patterns are preset at the factory: Button Indicator display 1 CONCERT 2 LIVE 3 CATHEDRAL 4 STADIUM 5 CLUB 6 CONCERT ٕ Fine-tuning an individual roomsize mode Detailed adjustments are available in any of the room size modes. 1. After pressing the [FUNC] button, hold button [1] down for more than a second. The DSP mode starts.
How to operate the receiver with an optional DSP/EQ unit connected [AUDIO CONTROL] button Buttons [1] to [6] 2. Tap button [AUDIO CONTROL] to select the desired mode of adjustment. The mode sequence on the button is as follows: Level•Duration value LR○○○dB (Reverberation level)* LR○○○S (Reverberation duration)* ER○○○dB (Initial echo level) ER○○○mS (Initial echo delay) * The level and duration adjustments are available in CONCERT and CATHEDRAL modes only. 3. Turn the [AUDIO CONTROL] button.
How to operate the receiver with an optional DSP/EQ unit connected Buttons [1] to [6] [FUNC] button 5. Push the [FUNC] button. The adjustment mode will be canceled and the selected room size will now take effect. ٕ Retrieving a preset pattern from memory Press a preset button to retrieve the room size in memory. The buttons under which room sizes are stored in memory are called preset buttons. 1. After pressing the [FUNC] button, hold button [1] down for more than one second. 2.
How to operate the receiver with an optional DSP/EQ unit connected Button [2] [FUNC] button عHow to operate the EQ functions The EQ functions enable level adjustments of various frequency groups for optimum listening conditions with a specific kind of music or musical instrument. ٕ Switching equalizer modes 1. After pressing the [FUNC] button, tap button [2] to switch equalizer modes. Six kinds of music categories are available for selection in the following sequence: 1. POPS 2. ROCK 3. JAZZ 4.
How to operate the receiver with an optional DSP/EQ unit connected [AUDIO CONTROL] button Buttons [1] to [6] [FUNC] button ٕFine-tuning EQ functions 1. After pressing the [FUNC] button, hold button [2] down for more than one second. The EQ adjustment mode starts. 2. Tap button [2] until the desired equalizer mode is displayed. 3. Tap the [AUDIO CONTROL] button to switch frequencies. The frequencies will switch in the following sequence: 63Hz 125Hz 250Hz 500Hz 1kHz 4kHz 12.5kHz 4.
How to operate the receiver with an optional DSP/EQ unit connected Buttons [1] to [6] [FUNC] button ٕRetrieving an equalizer mode from memory Press a preset button to retrieve the equalizer mode set in memory for the button. The buttons that set equalizer modes in memory are called preset buttons. 1. After pressing the [FUNC] button, hold button [2] down for more than one second. 2. Press a button, [1] to [6] . 3. Press the [FUNC] button.
If you have a question: [Reset] button ٟ If you have a question: First check the items mentioned below before attempting to troubleshoot problems. ٨ Caution ٨ • If a problem occurs, for instance when the unit does not respond to any button presses, or the display doesn't work press the reset button using a sharp tool. Pressing the reset button will delete all the entries from memory. The settings will return to those made at the factory prior to shipment. A CD that has been loaded will be ejected.
If you have a question: عDisplaying information (for troubleshooting) The information listed in the chart below is displayed to show the status of the CD player and CD changer. Refer to the chart for the appropriate action. Infomation Code Table When “INFO indicator . ”flash on the Nos.2-7 are displayed. Infomation Contents 2 NO DISK LOADED IN THE MAGAZINE 3 5 6 7 Explanation and remedial action to take. There is no disc in the magazine or player. Load adisc in the magazine. （Load a music disc.
If you have a question: Mode Problem Common Dead or weak sound to all Power does not turn on. Causes Remedial action to take Refer to page Is the volume control up sufficiently? Turn up the volume control. 21 Is the muting function in effect (MUTE)? Cancel the muting (MUTE) function. Is the fader or balance control set far to one side? Readjust the fader and 24 balance controls to more normal positions. Other probable causes include broken audio-signal wiring or a faulty speaker.
If you have a question: Causes Remedial action to take The disc cannot be inserted. The disc is ejected as soon as it is inserted. Or, the disc cannot be ejected. The disc cannot be changed. Is an extra label or seal applied to the disc? Do not apply labels or seals to the disc. 9 Are there rough edges, deformations or damaged areas on the disc? Try inserting another disc. Removed any burrs. Do not use a deformed or damaged disc. 10 Sound skips around. Sound is intermittent.
Specifications ٟ Specifications Power Supply Current Drain Dimensions (W x H x D) In-Dash Unit 14.4VDC (11-16V) 3A (1W) 7″×2″×6-1/8″(178×50×155mm) Frequency Range Usable Sensitivity 50dB Quieting Sensitivity Frequency Response Stereo Separation 87.75~107.
Specifications Frequency Response Wow & Flutter Stereo Separation S/N Ratio (A-weighted) Dynamic Range Total Harmonic Distortion 20~20,000Hz Below measurable limits 64dB 94dB 90dB 0.03% (1KHz)
Before Installation ٟ Before Installation Notes Be sure to disconnect the battery negative terminal before installing the receiver. عComponents No.
Mounting instruction ٟ Mounting instruction عMounting the main unit 1 . Insert the mounting sleeve into the opening in the vehicle console. 2 . Use a screwdriver or the like to bend the tabs in the mounting sleeve to secure the mounting sleeve. 3 . Attach the side brackets to the main unit using flathead screws.
Mounting instruction 4 . Mount the stud bolt to the main unit. 5 . Insert the main unit into the mounting sleeve until it locks in place. 6 . Fasten the rear of the main unit using either method [A] or [B]. Select method [A] or [B] to suit the interior configuration of the vehicle. 7 . Install the bezel on the main unit.
Mounting instruction Notes To prevent unconnected leads from shorting out, insulate them by wrapping their tips with electrical tape. Similarly, insulate the ends of connected leads. If an external amplifier is to be connected to the receiver, be sure to ground its outside housing to the vehicle body (a metal part). عNames of lead wires and destinations (refer to Page 71) No. Name Wire color 1 ACC Red Connect where the power comes on when the ignition is in the ACC position.
Mounting instruction 70
Mounting instruction عSystem 71
Black Blue/White Orange/White Blue Yellow Red 14 RR RL FR FL Mounting instruction
14 Mounting instruction 73
Mounting instruction 74
Mounting instruction IMPORTANT RECORD YOUR “ KEY CD” HERE… STORE YOUR “ KEY CD” ALONG WITH YOUR OWNER’S MANUAL IN YOUR SOCK DRAWER.
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. CUSTOMER NOTICE Please retain this booklet and write in the serial number of your 54420 for identification. The serial number is labeled or stamped on the chassis. Serial No. R by FUJITSU TEN DIVISION OF FUJITSU TEN CORP. OF AMERICA 19600 SOUTH VERMONT AVENUE, TORRANCE, CA 90502 (310) 327-2151 090001-13810700 9912DE(N.O.
