Deutsch In-Dash Portable Navigation with CD/USB Multi-Source Receiver English MODEL INSTALLATION MANUAL Français Contents Connections 2 For your safety in using the AVN2227P 3 Names and functions of terminals 5 Connecting the vehicle speed pulse 7 System connection example 8 Installing the GPS antenna Installing the main unit 9 11 Nederlands Installation Components Italiano Before installation Español Be sure to read this installation manual thoroughly prior to installation.
Deutsch Components Check that all of the following components are present Main unit components English 1 Main unit x 1 2 Interconnecting cable 3 Interconnecting cable (Power and speaker connector) (16P) x 1 5 Flat head screw 6 Splicing connector 7 Screw Español (Red:M5x8) x 8 9 Earth plate 4 Hex-head bolt (Speed pulse, Genuine steering remote control) (8P) x 1 (Red:M5x8) x 4 8 GPS antenna (M2x6) x 1 x1 x1 10 Cable tie x1 (for GPS antenna) x4 Français PND components 11 PND 12 CD
Warnings and caution signs, illustrated bellow, are posted throughout this manual as well as on the AVN2227P. They show safe and correct ways to handle the main unit so as to prevent personal injury to you and others and avoid damage to property. Before reading through the manual, take time to read through and learn the important information listed in this section.
Deutsch • For best results, this main unit should be installed by a professional installer. Contact the dealer whom you purchased the main unit for an appointment. • Once installation and wiring have been completed, return the brakes and electrical equipment such as lights, horn, hazard warning lights and turn signal lights to their original places, and check that they operate correctly.
8 F 1P ANTENNA PLUG 13P Français A B C Español 1 English • Never cut the insulation on the power cable or use it to power any other equipment. If the rated current capacity of the power cable is exceeded, fire and electric shocks may result. • The cables should be secured with tape or a similar securing method to prevent any obstructions while driving. If they get wound or entangled around components such as the steering wheel, shifting lever, or brake pedal, accidents may result.
Deutsch Cable colours and connection points for connection cables 1 2 and 3 Antenna power supply (Blue) Connect to the automatic-antenna control terminal of the vehicle. 2 Control power supply (Blue/White) Connect the control terminal for the external amplifier, etc. English 3 Cellular phone mute Cable (Pink) Connect to the earth output terminal on a mobile phone. 4 Earth (Black) Connect where good body earthing is available.
Notes on installation Tip The locations where the vehicle speed pulse signal cable may vary depending on the vehicle model and grade. Ask the car dealer or your nearest Eclipse dealer for details. - Connecting point for the vehicle speed pulse signal (example) - Engine computer Always be sure to connect the vehicle speed pulse, otherwise the measurement precision will be greatly reduced.
Deutsch System connection example English • Never cut the insulation on the power cable or use it to power any other main unit. If the rated current capacity of the power cable is exceeded, fire and electric shocks may result. • The cables should be secured with tape or a similar securing method to prevent any obstructions while driving. If they get wound or entangled around components such as the steering wheel, shifting lever, or brake pedal, accidents may result.
Notes on installation Tip • If installing the GPS antenna inside the vehicle, be sure it is mounted to the earth plate. • The materials used in front and rear vehicle windows can cause GPS reception sensitivity to drop significantly. If this happens, install the GPS antenna on the outside of the vehicle. • Wipe the installation surface thoroughly so that it is clear of any dirt, moisture, or grease before installing the antenna.
Deutsch 1 Choose an installation location on the dashboard which is flat and has a clear view of the sky. 10 8 Tip English • Select a location that is at least 50 cm. away from the main unit. If this is not done, the GPS measurement precision will drop. • Be sure to use the earth plate when installing the GPS antenna. If the earth plate is not used, the reception sensitivity will drop and will affect the accuracy of the position measurement. 2 Install the earth plate to the dashboard.
1 To maintain proper function, the unit must be mounted less than 30 degrees. If the angle is in excess of 30 degrees, CD skipping and improper CD ejection may occur. Deutsch Installing the main unit Front 30˚ or less 2 Remove the carrying bracket. 1 Tip English Level (reference) The hexagonal head bolts (Red) which are removed may be used again later when reinstalling.
Deutsch If installing using the 2DIN installation kit (sold separately) Tip Refer to the instructions provided with the kit (sold separately) for details on the installation method. If installing using the existing vehicle bracket and a multi-purpose bracket (such as for Japanese vehicles) English 6 Español 7 Attach the brackets to the main unit. 1 Tip Be sure to use the supplied accessory mounting screws (Red: M5 x 8) as the mounting screws.
