Specifications

74 GL-S MirrorBit
®
Family IS29GL_128S_01GS_00_Rev.A February 2015
Data Sheet
9.4 DC Characteristics
Notes:
1. I
CC
active while Embedded Algorithm is in progress.
2. Not 100% tested.
3. Automatic sleep mode enables the lower power mode when addresses remain stable for the specified designated time.
4. V
IO
= 1.65V to V
CC
or 2.7V to V
CC
depending on the model.
5. V
CC
= 3V and V
IO
= 3V or 1.8V. When V
IO
is at 1.8V, I/O pins cannot operate at >1.8V.
6. During power-up there are spikes of current demand, the system needs to be able to supply this current to insure the part initializes
correctly.
7. If an embedded operation is in progress at the start of reset, the current consumption will remain at the embedded operation specification
until the embedded operation is stopped by the reset. If no embedded operation is in progress when reset is started, or following the
stopping of an embedded operation, I
CC5
will be drawn during the remainder of t
RPH
. After the end of t
RPH
the device will go to standby
mode until the next read or write.
8. The recommended pull-up resistor for RY/BY# output is 5k to 10k Ohms.
Table 9.3 DC Characteristics (-40°C to +85°C)
Parameter Description Test Conditions Min
Typ
(Note 2)
Max Unit
I
LI
Input Load Current V
IN
= V
SS
to V
CC
, V
CC
= V
CC
max +0.02 ±1.0 µA
I
LO
Output Leakage Current V
OUT
= V
SS
to V
CC
, V
CC
= V
CC
max +0.02 ±1.0 µA
I
CC1
V
CC
Active Read Current
CE# = V
IL
, OE# = V
IH
, Address
switching@ 5 MHz, V
CC
= V
CC
max
55 60 mA
I
CC2
V
CC
Intra-Page Read Current
CE# = V
IL
, OE# = V
IH
, Address
switching@ 33 MHz, V
CC
= V
CC
max
925mA
I
CC3
V
CC
Active Erase/Program
Current (Notes 1, 2)
CE# = V
IL
, OE# = V
IH
, V
CC
= V
CC
max 45 100 mA
I
CC4
V
CC
Standby Current
CE#, RESET#, OE# = V
IH
, V
IH
= V
IO
V
IL
= V
SS
, V
CC
= V
CC
max
70 100 µA
I
CC5
V
CC
Reset Current (Notes 2, 7)
CE# = V
IH
, RESET# = V
IL
,
V
CC
= V
CC
max
10 20 mA
I
CC6
Automatic Sleep Mode (Note 3)
V
IH
= V
IO
, V
IL
= V
SS
,
V
CC
= V
CC
max, t
ACC
+ 30 ns
36mA
V
IH
= V
IO
, V
IL
= V
SS
,
V
CC
= V
CC
max, t
ASSB
100 150 µA
I
CC7
V
CC
Current during power up
(Notes 2, 6)
RESET# = V
IO,
CE# = V
IO
, OE# = V
IO
,
V
CC
= V
CC
max,
53 80 mA
V
IL
Input Low Voltage (Note 4) -0.5 0.3 x V
IO
V
V
IH
Input High Voltage (Note 4) 0.7 x V
IO
V
IO
+ 0.4 V
V
OL
Output Low Voltage (Notes 4, 8)
I
OL
= 100 µA for DQ15-DQ0;
I
OL
= 2 mA for RY/BY#
0.15 x V
IO
V
V
OH
Output High Voltage (Note 4) I
OH
= 100 µA 0.85 x V
IO
V
V
LKO
Low V
CC
Lock-Out Voltage
(Note 2)
2.25 2.5 V
V
RST
Low V
CC
Power on Reset Voltage
(Note 2)
1.0 V