Measurement Guide

Cordless Motorized Roman
Shade Installation Instructions
Step 1 – Checklist
You will need the following tools:
- Drill
- Pencil
- Step Ladder
- Tape Measure
- Small Level
- Light Weight Hammer
- Screwdriver
Step 5 – Maintaining Your Shade
Dust your shades with a soft clean cloth or a feather duster. Lower the
shade to its fullest length for a complete cleaning. You can also detach
the shade from the bar, with the hook and loop fastener and lightly
shake for a simple cleaning.
*Top fabric face is detachable, but not fully removable.
Mounting inside the Window Frame (Ceiling)
Step 2 – Mounting Brackets
The Roman Shade (a) can be mounted two ways; either Inside (Ceiling
Mount) or Outside (Wall Mount) of your window frame using the provided
Brackets (b). You will need to leave 3-5 inches of space from the ends of
the Headrail (h) to properly mount the Brackets. ALWAYS use the Wall
Anchors (d) if you are mounting the brackets onto dry wall.
Using a 13/64 drill bit, drill a hole for the bracket screws.
With a light weight hammer, insert the anchors until ush with the surface.
Mounting Outside the Window Frame (Wall)
Fix the Brackets (b) on the wall outside and above the window frame.
Ensure that the Brackets (b) are moved in 3-5 inches from the sides of the
window frame. Then place the Bracket Screws (c) through holes on the
back plate of the Bracket (b) and tighten until securely fastened to the wall.
Follow the same instructions as above to install the Wall Anchor (d),
then place the Bracket (b) over the anchor. Insert the screw and fasten.
Step 4 – Operation of Your Shade
To charge the shade:
To raise and lower the shade:
Press and hold the up/down button on the Remote (e) to raise/lower Shade (a)
to the desired height. The middle button will stop the Shade (a) while in motion.
Press up/down twice to bring Shade (a) fully up or down at once.
Headrail (h)
(a)
(b)
Step 3 – Fitting the Shade & Securing the Headrail
Place the Headrail (h) onto the
Brackets (b) by inserting the
back side of the Headrail (h) on rst
and then pushing the front side
upward until it snaps into place.
There should be an audible click,
when the Headrail (h) is secured.
Once secured, reattach the Roman Shade (a) to the hook and loop
fastener on the front of the Headrail (h).
For easier tting, detach the
Roman Shade (a) from the hook
and loop fastener on the front
of the Headrail (h).
*Top fabric face is detachable,
but not fully removable.
Content
Shade
Size
Shade
(a)
Bracket
(b)
Bracket
Screw
(c)
Wall
Anchor
(d)
27in. x 64in. 1 2 4 4
31in. x 64in. 1 2 4 4
33in. x 64in. 1 2 4 4
35in. x 64in.
1 2 4 4
39in. x 64in.
1 4
36in. x 64in.
1 2 4 4
2 4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
For helpful videos &
more information visit
eclipsecurtains.com
or scan the QR code below
with your smartphone
Charger
Cable
(f)
Remote
(e)
(e)
(f)
Connect the USB-C end of the Charger Cable (f) to port attached to
front of the Headrail (h). The USB-A end of the Charger Cable (f) will
need to be attached to a common power supply (not provided).
Screw-
driver
(g)