OWNER'S MANUAL CD8445 ESN E8 High-Power "Customize" CD/MS Receiver with MP3/WMA Decoder and Remote We appreciate your purchase of this receiver. Please read through this manual for correct operation. We suggest that after reading it you keep this manual in a safe place for future reference.
CD8445.book 2 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 For your safety in using the CD8445 Warnings and caution signs, illustrated below, are posted throughout this manual as well as on the CD8445. They show safe and correct ways to handle the product so as to prevent personal injury to you, others and to avoid property damage. Before reading through the manual, take time to read through and learn the important information listed in this section.
CD8445.book 3 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Warning ● Do not modify this system for use other than that specified herein. Also, do not deviate from the installation procedures described herein; Eclipse will not be held liable for damages including, but not limited to serious injury, death or property damage resulting from installations that enable unintended operation. ● This equipment requires 12V DC and should only be installed in a vehicle with a 12V negative ground electrical system.
CD8445.book 4 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Warning ● To avoid equipment and vehicle damage, including fire, never supply power to installed equipment in a way which will overload the capacity of an existing vehicle circuit. Never leave a power supply wire or connection uninsulated. Always install supplied fuses, circuit breakers, and relays. ● Air bags are vital safety equipment. Never install equipment in a way which will alter air bag wiring or interfere with air bag deployment.
CD8445_00_E.fm 5 ページ ２００４年１２月１６日 木曜日 午後５時２４分 Warning ● Do not use when it is broken (the screen is not lit or no sound comes out). Accidents, fires or shocks may result. ● Always replace fuses with fuses of identical capacity and characteristics. Never use a high capacity fuse than the original. Using the wrong type of fuse may cause a fire or severe damage.
CD8445.book 6 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Caution ● Wiring and installing this equipment requires expertise and experience. Professional installation is recommended. Consult with your dealer or a professional installer. Incorrect wiring may damage the equipment or interfere with safe vehicle operation. ● Use only the accessory parts as specified. Using other parts may cause damage to the equipment or cause parts to fall or fly off the equipment.
CD8445.book 7 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Caution ● Avoid hot surfaces when wiring equipment. High temperatures may damage wiring, causing shorts, arcing and fires. ● When changing the installation location for this equipment, please consult the dealer where you bought it for safety reasons. Expertise is necessary for removal and installation. ● Keep volume to a reasonable level so that you can hear sounds from outside the vehicle, including warning sounds, voices, and sirens.
CD8445.book 8 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Caution ● Do not short, disassemble or heat the batteries, or place them in fire or water. Fire and injuries may result from battery rupture and leakage. ● Store the remote control in a place away from direct sunlight, high temperatures, and high moisture levels. The case may change shape, and the batteries may rupture and leak. ● Do not use this equipment except for in-vehicle use. Shocks or injuries may result.
CD8445.book 9 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Table of Contents Operating precautions.............................................................................. 16 I Names of controls and parts.................................................................... 23 II ESN security operating precedure .......................................................... 24 III Basic operation .........................................................................................
CD8445.book 10 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Table of Contents Operating precautions......................................................................... 16 Notes on operation........................................................................................................ 16 About compact discs ..................................................................................................... 17 About cleaning a CD .............................................................................
CD8445.book 11 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Enabling the loudness control ....................................................................................... 49 Making changes with Display Adjustment Mode........................................................... 50 Switching the motion picture................................................................................... 51 Switching the brightness.........................................................................................
CD8445.book 12 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Listening to MP3/WMA file ............................................................................................ 86 Advancing to the next track (file) or returning to the beginning of the track (file) being played.................................................................................................................. 87 Skipping to the next or previous folder..........................................................................
CD8445.book 13 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Parametric equalizer............................................................................................. 116 Time Alignment..................................................................................................... 118 Crossover ............................................................................................................. 119 Multi-harmonizer .....................................................................................
CD8445.book 14 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Switching playback modes.......................................................................................... 164 How to play the tuner .................................................................................................. 164 Selecting the FM/AM band ................................................................................... 164 Selecting a station (manually or automatically) ....................................................
CD8445TOC.fm 15 ページ ２００４年１２月１６日 木曜日 午後５時３２分 Manually setting channels into memory ...................................................................... 185 Preset channel scan ................................................................................................... 186 Switching displays when using the SIRIUS satellite radio .......................................... 186 Others .................................................................................................
CD8445.book 16 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Operating precautions Operating precautions Notes on operation ● For your safety, play only at volume levels that allow outside sounds to be heard. TEXT MEMORYSTICK MAGICGATE ● We recommend using with this player a disc with the logo shown to the left. ● You can play music CDs(CD-R/CD-RW) on this player. Be sure to use discs that have been properly processed.
CD8445.book 17 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Operating precautions MEMORYSTICK MAGICGATE ● Cleaning the disc slot. The disc slot tends to get dusty. Clean it occasionally to prevent accumulated dust from scratching the discs. ● With the front panel open, many functions will not operate, therefore, the front panel will need to be closed during operation. About compact discs ● The signal recorded on a compact disc is read by a laser beam, so nothing touches the disc surface.
CD8445.book 18 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Operating precautions About brand new CDs About CD accessories ● You may notice that some brand new discs are rough around the center hole or outside edge. Remove the rough edges with the side of a ballpoint pen, etc. Rough edges may prevent proper loading in the deck. Flakes from the rough edges may also stick to the recorded surface and interfere with playback. ● Do not use accessories (stabilizers, protective seals, laser lens cleaners, etc.
CD8445.book 19 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Operating precautions About borrowed CDs About irregularly-shaped CDs ● Do not use a CD with glue or remnants of adhesive tape or labels. They may cause the CD to get stuck inside or damage the deck. ● Specially-shaped CDs, like heartshaped or octagonal CDs, cannot be played. Do not attempt to play them, even with an adapter, since they may damage the player. How to remove CDs ● When removing the ejected disc, pull it straight out along the slot.
CD8445.book 20 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Operating precautions About Memory Sticks ● Do not store Memory Sticks in places that are subject to static electricity and electrical interference, otherwise the data they contain may become corrupted. ● In order to protect the player, the player's functions will be stopped automatically if a problem occurs.
CD8445.book 21 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Operating precautions ● MG Memory Stick supplied is not formatted. MG Memory Stick must be formatted prior to use. Refer to "Formatting MG Memory Stick (quick format)" on page 102 for instructions on formatting MG Memory Sticks. ● It may not be possible to use MG Memory Sticks that have just been purchased. If this happens, use the unit to format the MG Memory Stick.
CD8445.book 22 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Operating precautions About cleaning the Memory Sticks ● In order to maintain good audio performance from Memory Sticks, periodically wipe the cartridge clean of any dust and other contamination with a dry cloth.
CD8445.book 23 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Names of controls and parts Names of controls and parts Front view II With the front open MEMORYSTICK MAGICGATE Never place an object or rest your hands or the like on the front panel. [CD ] button Opens/closes front panel and ejects CD. [AUDIO CONTROL] button Adjusts volume and performs other functions. [DISC MS] button Switches disc modes, Memory Stick mode and switches to AUX mode. [OPEN] button Opens/closes front panel.
CD8445.book 24 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure ESN security operating procedure About ESN This deck is equipped with ESN (ECLIPSE Security Network). A preregistered music CD (Key CD), four-digit security code, or a Memory Stick on which all unit functions will not operate, even by turning the ignition switch to the ACC or ON position or reconnecting the battery after turning the ignition switch off or disconnecting the battery during maintenance.
CD8445.book 25 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure [FUNC] button Button [3] III How to switch the security type (Key CD security/ Memory Stick security) You can switch the type of security being used (Key CD security or Memory Stick security). The initial setting is for Key CD security to be used. Check that the unit is in standby. Press and hold the [FUNC] button, then button [3], and hold both for the more than two seconds.
CD8445_03_E.fm 26 ページ ２００４年１２月１３日 月曜日 午後１時３８分 ESN security operating procedure [CD ] button [OPEN] button [FUNC] button Button [6] How to operate the ESN (Key CD) security How to program the Key CD Check that the unit is in standby. Press and hold the [FUNC] button, then button [6], and hold both for more than one second. A [SEC] message appears, in two seconds it will change to [DISC].
CD8445.book 27 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure ● If there is a problem with the inserted CD, an [ERR] message will appear for two seconds and the CD will be ejected. Reinsert the ejected CD. ● If a CD causes the [ERR] message to appear twice in a row, a [CHANGE] message will appear for two seconds. Try another CD. ● Copy Protected CD and MP3/WMA CD-ROM cannot be programmed for Key CD security.
CD8445.book 28 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure [CD ] button [OPEN] button [FUNC] button Button [6] How to change the Key CD First, cancel the existing Key CD. Refer to "How to cancel the key CD". Next, program a new Key CD. Refer to "How to program the Key CD". How to resume normal operation (ESN security lock out) If power is disconnected while ESN security is active (a Key CD was programmed), operation is disabled until power is restored and the unit unlocked.
CD8445.book 29 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure What happens if an incorrect CD is inserted? After the 5th incorrect attempt, the display reads [HELP] for five seconds. After the [HELP] message will appear for five seconds, serial number will appear. Press the [OPEN] or [CD panel. ] button to close the front Press the [FUNC] button, then button [6], and hold them for five seconds. After the [SEC] message will appear for two seconds, rolling code (six digit) will appear.
CD8445_03_E.fm 30 ページ ２００５年４月２５日 月曜日 午前９時５０分 ESN security operating procedure [FUNC] button Buttons [1] to [4] Button [6] How to operate the ESN (Memory Stick) security How to record a security code Check that the unit is in standby. Press and hold button [1], then the [FUNC] button, and hold both for more than one second. A [SEC] message appears, in two seconds it will change to [MS]. ● If a Memory Stick has already been inserted, a [MS EJECT] message appears.
CD8445.book 31 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure Press the [FUNC] button for more than one second. The security code is registered in the deck and security is set. The registered security code is encrypted and then written to Memory Stick. When the security code is registered using a Memory Stick that contains several kinds of data, such as music, etc., be careful not to clear the recorded data by formatting the Memory Stick. Eject the Memory Stick.
CD8445_03_E.fm 32 ページ ２００５年４月２５日 月曜日 午前９時５１分 ESN security operating procedure [FUNC] button Buttons [1] to [4] Button [6] How to cancel the Memory Stick security The security function can be canceled when the security code that has been recorded with the deck is entered and verified. Canceling the security function can be done by entering the security code into the deck, or by using the Memory Stick. Canceling the security function by entering the security code Check that the unit is in standby.
CD8445_03_E.fm 33 ページ ２００５年４月２５日 月曜日 午前９時５１分 ESN security operating procedure [DISC] button [FUNC] button Button [6] Canceling the security function using a Memory Stick Check that the unit is in standby. Press and hold button [1], then the [FUNC] button, and hold both for more than one second. A [SEC] message appears, then in two seconds it will change to [- - - -] (Security code input display). Press the [DISC] button. A [MS] message will appear.
CD8445.book 34 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure How to change the Memory Stick You can change the Memory Stick and security code that have been recorded by the deck to a different Memory Stick and security code. Cancel the security code that has been recorded with the deck. Refer to "How to cancel the Memory Stick security" on page 32. Re-record the new Memory Stick and security code that you would like to use. Refer to "How to record a security code" on page 30.
CD8445.book 35 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure [FUNC] button Buttons [1] to [4] How to resume normal operation (ESN security lock out) If power is disconnected while ESN security is active (a security code was recorded), operation is disabled until power is restored and the unit unlocked. Follow this procedure to resume normal operation.
CD8445.book 36 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure [DISC] button [FUNC] button Press the [FUNC] button for more than one second. If the security code matches the code recorded by the deck, [OK] will appear on the display and the security function will be canceled.
CD8445.book 37 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure If the contents recorded in the Memory Stick match the information recorded by the deck, [OK] will appear on the display for two seconds, and then the deck will return to normal operation. ● If the contents recorded in the Memory Stick do not match the information recorded by the deck, [ERR_] (ERR and the error number) will appear on the display for two seconds, and then [- - -] (security code entry display) will appear.
CD8445.book 38 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure [FUNC] button Button [5] How to operate the ACC security ACC security involves using Memory Stick security to record a security code, and then when the ignition switch is turned to OFF and back to ACC, the operation of all buttons is disabled. Check that the unit is in standby. Once a security code has been recorded, press the [FUNC] button and button [5] simultaneously for more than two seconds.
CD8445.book 39 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure [FUNC] button Button [2] III How to turn the security indicator on/off Once ESN security is activated, the indicator flashes whenever the vehicle's ignition switch is turned off, warning potential thieves that the unit is protected. However, if do not want this visible deterrent, it may be turned off. With the unit in standby, press the [FUNC] button, then button [2] and hold both for more than one second. [IND.
CD8445.book 40 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 ESN security operating procedure [FUNC] button Button [4] How to read the Electronic Serial Number Check that the unit is in standby. Press and hold the [FUNC] button, then button [4], and hold both for more than one second. [ESN] appears on the display, followed by an eight-digit number; this number is your electronic serial number (ESN). You may use this number to identify your Eclipse CD8445 in the event of theft recovery.
CD8445.book 41 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation Basic operation [PWR] button This section covers basic operating procedures. For additional details, please refer to the sections on specific functions. Turning the power on and off When the power is turned on, the state used when the power was turned off such as CD and tuner playback is restored. When the vehicle has no ACC position on the ignition switch, care is needed when turning off the deck.
CD8445.book 42 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [CD ] button [OPEN] button [DISC MS] button Listening to CD Press the [OPEN] or [CD ] button. The front panel opens. Insert a CD into the disc slot, label side up. The CD will immediately start playing. When a CD is already loaded, press the [DISC MS] button to switch to the CD mode. Do not press the [OPEN] or [CD ] button while CD is being inserted. This could cause an injury and damage to the front panel.
CD8445.book 43 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [CD ] button [OPEN] button [DISC MS] button Listening to MG Memory Stick Press the [OPEN] or [CD IV ] button. The front panel opens. Insert a MG Memory Stick into the Memory Stick slot. ● Insert the MG Memory Stick with the mark facing inwards and press MG Memory Stick into place until a clicking sound is heard.
CD8445.book 44 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [SEL] button [FM AM] button Buttons [1] to [6] [ [ ] button ] button Listening to the tuner Press the [FM AM] button. This will turn the tuner on. Press the [FM AM] button for less than one second to switch to the desired FM or AM bands. For example, radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM with each press of the button. Turn the [SEL] button to the left or right to tune to a station.
CD8445_04_E.fm 45 ページ ２００４年１２月１６日 木曜日 午後５時３６分 Basic operation [MUTE] button [AUDIO CONTROL] button Adjusting audio volume IV Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Increases the volume. Turn to the left: Decreases the volume. Press the [MUTE] button for less than one second to cut the volume or restore it instantly. Do not adjust the volume or other controls while driving the vehicle. Do so only while parked in a safe location.
CD8445.book 46 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [AUDIO CONTROL] button Switching audio control modes Various audio control modes may be fine-tuned using this procedure. Press the [AUDIO CONTROL] button for less than one second to select the item to be adjusted. Modes will switch in the order shown below each time the button is pressed.
CD8445.book 47 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [AUDIO CONTROL] button MID (MIDDLE) Mode Adjusts middle level. Mid mode can be adjusted for each source (CDP/CDC, FM and AM and Memory stick player). Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Emphasizes medium sounds. Turn to the left: Softens medium sounds. TREB (TREBLE) Mode Adjusts treble level. Treble mode can be adjusted for each source (CDP/CDC, FM and AM and Memory stick player).
CD8445.book 48 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [AUDIO CONTROL] button SVC (Source Volume Control) Mode You can set different volume levels for each audio mode. The volume for the initial FM mode (default value: 40) is used as a reference for storing the differences in volume that have been set for each audio mode. When SVC is set, the volume level can change as shown in the example settings in the table below.
CD8445.book 49 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [AUDIO CONTROL] button Turn the [AUDIO CONTROL] button to the left or right. Turn to the right:Increases the SVC setting level. Turn to the left:Decreases the SVC setting level. The volume difference can be set within a range of -10 to +20. If the battery terminals have been disconnected because of a reason such as vehicle maintenance, the SVC settings will return to their default values.
CD8445.book 50 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [SEL] button [DISP] button Making changes with Display Adjustment Mode This mode lets you adjust the display brightness, change the button illumination color and turn the display on and off. Press the [DISP] button for less than one second. Enters display adjustment mode. If you press the [DISP] button during display adjustment mode, the display adjustment mode is canceled and the mode returns to normal music mode.
CD8445.book 51 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [SEL] button [DISP] button [RTN] button Switching the motion picture You can select a moving picture screen that is already available in the deck and show it on the display. The deck has three types of motion picture available. In addition, moving picture screens provided by the ECLIPSE website (E-iSERV) can be downloaded, imported into the deck and displayed.
CD8445.book 52 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [SEL] button [DISP] button [RTN] button Switching the brightness Adjust the display brightness to the best level. Turn the [SEL] button to select Bright. The selected item will be highlighted. Press the [SEL] button. The mode will change to luminance adjustment mode. Turn the [SEL] button to adjust brightness. When the button is turned, the brightness level changes in the following order. (Level) 1↔2↔3↔4↔5 Press the [SEL] button.
CD8445.book 53 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [SEL] button [DISP] button [RTN] button Changing illumination color You can change the button illumination color in the following way. Turn the [SEL] button to select ILL. The selected item will be highlighted. Press the [SEL] button. The screen for changing the illumination color will appear. Turn the [SEL] button to adjust the illumination color. When the button is turned, the illumination color changes in the following order.
CD8445.book 54 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [SEL] button [DISP] button [RTN] button Disabling the display You can turn the display on and off in the following way. Turn the [SEL] button to select Disp ON/OFF. The selected item will be highlighted. Press the [SEL] button. The screen for turning the screen display on and off will appear. Turn the [SEL] button to select ON or OFF. The selected item will be highlighted. Press the [SEL] button. The selected settings will take effect.
CD8445.book 55 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation Importing DISP screens Moving picture screens provided by the ECLIPSE website (EiSERV) can be downloaded and used instead of pre-set moving pictures. To download moving picture screens follow the ECLIPSE website (E-iSERV). After downloading the data to your PC, copy the data to a Memory Stick or CD-R and import the data into the deck. (URL: http://www.e-iserv.
CD8445.book 56 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [OPEN] button [SEL] button [DISP] button [RTN] button Turn the [SEL] button to select Disp Data. The selected item will be highlighted. Press the [SEL] button. The Disp Data mode is activated. Turn the [SEL] button to select media types. Press the [SEL] button. ● When using a CD-R: The front panel opens automatically and, if a CD has already been loaded into the deck, it will automatically eject.
CD8445.book 57 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation Press the [SEL] button. This begins importing the data into the deck. If the data has already been imported, the data will be overwritten. When importing has completed, [Completed] will appear and the front panel opens automatically, and CD-Rs will automatically eject. Press the [OPEN] button to close the panel.
CD8445.book 58 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [SEL] button [DISP] button [RTN] button Displaying Amplifier Status (E-AMP DISP) If a DSP Amp is connected, the status of the DSP amp will be displayed. Turn the [SEL] button to select E-AMP DISP. The selected item will be highlighted. Press the [SEL] button. The E-AMP DISP mode is activated. Turn the [SEL] button to select which amplifier status you wish to display.
CD8445.book 59 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [FUNC] button [SEL] button Making changes with Function Mode IV A variety of settings can be changed. Press the [FUNC] button for less than one second. The function mode is activated. If you press the [FUNC] button during function mode, the adjustment mode is canceled and the mode returns to normal music mode. Turn the [SEL] button in either direction to display setting items for selection.
CD8445.book 60 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation *5: This setting can only be chosen when HD radio reception is available. (Refer to page 179 for details on HD Radio operation.) *6: Refer to page 188 for details on AUX Sensitivity. *7: Refer to page 65 for details on Steering switch. *8: U.S.A. only.
CD8445.book 61 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [FUNC] button [SEL] button [RTN] button Disabling the guide tone feature (for button operation) The receiver is set at the factory to emit a beep tone in response to button operation. The guide tone feature may be disabled in the following procedure: Turn the [SEL] button to select Guide Tone. The selected item will be highlighted. Press the [SEL] button. The guide tone mode will be switched ON/OFF.
CD8445.book 62 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [FUNC] button Button [6] [SEL] button [RTN] button Clock display on/off Switches the clock display to ON/OFF. Turn the [SEL] button to select Clock. The selected item will be highlighted. Press the [SEL] button. The clock display ON/OFF mode is activated. Turn the [SEL] button to select ON or OFF. The selected item will be highlighted. Press the [SEL] button. The selected settings will take effect. Press the [RTN] button.
CD8445.book 63 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [FUNC] button [SEL] button [RTN] button Setting the time This receiver uses the 12-hour display notation. Turn the [SEL] button to select Clock Adjust. The selected item will be highlighted. Press the [SEL] button. The clock adjustment mode is activated. Press the [SEL] button to display the item to be selected for adjustment. Hours or minutes will be switched each time the button is pressed. Turn the [SEL] button.
CD8445.book 64 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [FUNC] button [SEL] button [RTN] button Switching demonstration screen display You can set the demonstration screen display to appear or not appear when the power is turned on. When the power turns on, the various demonstration screens such as the audio operation screens and motion picture screens will appear repeatedly in the following order.
CD8445.book 65 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation Setting the steering switch function (U.S.A. only) The vehicle’s factory loaded steering switch becomes inoperable when the CD8445 is installed. The ECLIPSE website (E-iSERV) provides software that enables steering switch operation even with the installation of the deck. Import this software into your CD8445. For details, contact the store from which you purchased your deck.
CD8445.book 66 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [OPEN] button [FUNC] button [SEL] button [RTN] button Reading steering switch data The steering switch data that has been downloaded from E-iSERV (website) to a Memory Stick or CD-R can be loaded into the deck and saved there. Press the [FUNC] button for less than one second. The function mode is activated. Turn the [SEL] button to select Steering SW. Press the [SEL] button. Select media by turning the [SEL] button.
CD8445.book 67 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation When using a Memory Stick: Data downloaded from the ECLIPSE website (E-iSERV) can be saved in folders on the Memory Stick as follows: MSFTEN User creation DATA Automatic creation XXXXXXXX.ssw File extension ● Files that can be imported into the deck are created automatically when downloaded from the E-iSERV website. ● The file name can be changed using 8 alphameric characters (space cannnot be used).
CD8445_04_E.
CD8445.book 69 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation Others Operation assist function In display adjustment mode, function mode and sound adjustment mode, the screen displays help to guide you in carrying out operations. The buttons that are used for adjustment operation flash. The function button selected for adjustment is displayed.
CD8445.book 70 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation Buttons [1] to [5] [ ] button [SEL] button [ ] button Displaying a memo If memos have been set, a memo recorded corresponding to a number button [1] to [5] appears on the screen when the number button is pressed briefly while the power of the main unit is turned off. Setting a memo Press and hold any number button for more than two seconds while in the Standby mode. The state shifts to the MEMO setting mode.
CD8445.book 71 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Basic operation [SEL] button Button [6] [RTN] button Turn the [SEL] button to the left or right to select IV characters. Turn to the right: Advances the character forward in its type. Turn to the left: Moves the character backward in its type. [Upper-case alphabet characters] Initial value [A] A¡B¡C¡...X¡Y¡Z [Numeric characters] Initial value [1] 1¡2¡3¡...
CD8445.book 72 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the CD player How to operate the CD player [DISC MS] button First press the [DISC MS] button for less than one second to switch to the disc mode. It is assumed here that a CD has already been loaded into the unit. Listening to CDs Press the [DISC MS] button for less than one second to switch to the CD player mode. This starts CD play. Disc mode will switch from CD player ➔ order each time the button is pressed.
CD8445.book 73 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the CD player [SEL] button [ ] button [ ] button [4 SCAN] button Advancing to the next track or returning to the beginning of the track being played Turn the [SEL] button to the left or right. Turn to the right: Advances to the next track. Turn to the left: Returns to the beginning of the track being played. (Repeat turning for previous tracks.) Fast Forward/Rewind Fast forward or rewind the song currently being played.
CD8445.book 74 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the CD player [5 RPT] button [6 RAND] button Repeating the same track (REPEAT) Press the [5 RPT] button to repeat the track being played. To cancel, press the [5 RPT] button again. Playing tracks in random order (RANDOM) Press the [6 RAND] button to play the tracks in random order. To cancel, press the [6 RAND] button again. ● During random playback, press the [5 RPT] button to repeat the track being played.
CD8445.book 75 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the CD player [CD ] button [OPEN] button Ejecting the disc Press the [CD ] button. The front panel opens and the disc is ejected. Remove the disc and press the [CD ] or [OPEN] button. The front panel closes. If left alone for 15 seconds after the disc ejection, the front panel closes after the BEEP sound. ● Do not drive with the front panel open. The panel may cause unexpected personal injury during a panic stop, or the like.
CD8445.book 76 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the CD player [FUNC] button [SEL] button [ [ ] button ] button [RTN] button Creating a title for a CD A CD title may be created, attached and displayed for your discs. If external CD changers are connected, a title for a CD will be created in the same way. It is assumed here that the CD to be titled is playing. No CD text disc can be set. Press the [FUNC] button for less than one second while in the disc mode.
CD8445.book 77 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the CD player Turn the [SEL] button to the left or right to select characters. Turn to the right: Advances the character forward in its type. Turn to the left: Moves the character backward in its type. [Upper-case alphabet characters] Initial value [A] A¡B¡C¡...X¡Y¡Z [Numeric characters] Initial value [1] 1¡2¡3¡...8¡9¡0 [Right direction] [Right direction] [Symbol] Initial value [!] [Right direction] !¡"¡#¡$¡%¡&¡’¡(¡)¡*¡+¡,¡–¡.
CD8445.book 78 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the CD player [SEL] button [FUNC] button [ ] button [RTN] button Changing a previously set title If external CD changers are connected, a previously set title for a CD will be changed in the same way. It is assumed here that the disc mode is selected. Press the [FUNC] button for less than one second while in the disc mode. The function mode is activated. Turn the [SEL] button to select Title. The selected item will be highlighted.
CD8445.book 79 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the CD player Turn the [SEL] button to the left or right to select characters. Turn to the right: Advances the character forward in its type. Turn to the left: Moves the character backward in its type. Press the [SEL] button. The selected settings will take effect. To leave a space blank, follow these steps. 1.Select and flash the space to be blank. 2.Turn the [SEL] button to make a blank space flashing. 3.Press the [SEL] button to move.
CD8445.book 80 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the CD player [FUNC] button [SEL] button [6] button [RTN] button Deleting a previously created title If external CD changers are connected, a previously created title for a CD will be deleted in the same way. It is assumed here that the disc mode is selected. Press the [FUNC] button for less than one second while in the disc mode. The function mode is activated. Turn the [SEL] button to select Title. The selected item will be highlighted.
CD8445.book 81 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the CD player [DISP] button Displaying CD text Only the built-in CD player supports CD TEXT. It can not be displayed with the optional CD changer. If the CD came with a logo shown below, it is recorded with a disc title and track titles. These information will be displayed during playback. Press the [DISP] button for more than one second.
CD8445.book 82 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the MP3/WMA player How to operate the MP3/WMA player About MP3/WMA The making of MP3/WMA files by recording from sources such as broadcasts, records, recordings, videos and live performances without permission from the copyright holder for uses other than personal enjoyment is prohibited. What is MP3/WMA? MP3 (MPEG Audio Layer III) is a standard format for audio compression technology.
CD8445.book 83 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the MP3/WMA player ID3/WMA tags MP3/WMA files have an "ID3/WMA Tag" that allows input of information so that data such as song title and artist can be saved. This deck supports ID3v. 1.0, 1.1 and WMA tags. Media Media capable of playing MP3/WMA includes CD-R and CD-RW discs.
CD8445.book 84 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the MP3/WMA player Format of discs The format of discs to be used must be ISO9660 Level 1 or Level 2. Control items for this standard are as follows: ● Maximum directory layers: 8 layers ● Maximum characters for folder names/file names: 32 (including ".
CD8445.book 85 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the MP3/WMA player File names Only files with the MP3/WMA file extension ".mp3", ".wma" can be recognized as MP3/WMA and played. Be sure to save MP3 files with the ".mp3" file extension. Be sure to WMA files with the ".wma" file extension. The "MP" or "WMA" letters of the file extension will be recognized whether entered as uppercase letters or lowercase letters. If the ".mp3", ".
CD8445.book 86 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the MP3/WMA player [DISC MS] button Button [3] Listening to MP3/WMA file Press the [DISC MS] button for less than one second to switch to the CD player mode. This starts MP3/WMA file play. Disc mode from CD player ➔ Memory Stick player in order each time the button is pressed. If an external CD changer is connected, each additional press of the [DISC] button will switch modes from CD changer 1 ➔ CD changer 2 ➔ Memory Stick player ➔ CD player.
CD8445.book 87 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the MP3/WMA player [SEL] button [ ] button Buttons [1 ] and [2 [ ] button [RTN] button ] Advancing to the next track (file) or returning to the beginning of the track (file) being played Turn the [SEL] button to the left or right. Turn to the right: Advances to the next track (file). Turn to the left: Returns to the beginning of the track (file) being played. Repeat turning for previous tracks (files).
CD8445.book 88 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the MP3/WMA player [4 SCAN] button [5 RPT] button Playing the beginning of files (SCAN) Press the [4 SCAN] button. Press the button briefly to play just the first 10 seconds of each song for all the files in the same layer of the folder being played. Pressing the button until [FOLDER SCAN] is displayed will play just the first 10 seconds of the first song in each folder.
CD8445.book 89 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the MP3/WMA player [5 RPT] button [6 RAND] button Playing files in random order (RANDOM) Press the [6 RAND] button. Press the button briefly to randomly play the files in the same layer as the folder being played. Pressing the button until [ALL RANDOM] is displayed will randomly play the files in all the folders. To cancel, press the [6 RAND] button again. ● During random playback, press the [5 RPT] button to repeat the file being played.
CD8445.book 90 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the MP3/WMA player [DISP] button Displaying title Press the [DISP] button for more than one second. Each time the button is pressed, the following will be displayed in order. Folder Name/File Name* ➔ Tag *: The display area shows a maximum of 14 characters and then scrolls to display the remaining characters. After the folder name is displayed, the file name will be displayed by scrolling.
CD8445_07_E.fm 91 ページ ２００４年１２月１６日 木曜日 午後４時４９分 How to operate the Memory Stick player How to operate the Memory Stick player Music data recorded on "MG Memory Stick" with ATRAC3 (an audio compression technology) can be played on this deck. Recording from music CD to the MG Memory Stick is also possible. The following explanation for the operation is made assuming that the MG Memory Stick has already been inserted. First press the [DISC MS] button for less than one second to switch to the disc mode.
CD8445.book 92 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player [ ] button [4 SCAN] button [SEL] button [ ] button Advancing to the next track or returning to the beginning of the track being played Turn the [SEL] button to the left or right. Turn to the right: Advances to the next track. Turn to the left: Returns to the beginning of the track being played. (Repeat turning for previous tracks.) Fast Forward/Rewind Fast forward or rewind the song currently being played.
CD8445.book 93 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player [5 RPT] button [6 RAND] button Repeating the same track (REPEAT) Press the [5 RPT] button to repeat the track being played. To cancel, press the [5 RPT] button again. Playing tracks in random order (RANDOM) Press the [6 RAND] button to play the tracks in random order. To cancel, press the [6 RAND] button again. ● During random playback, press the [5 RPT] button to repeat the track being played.
CD8445.book 94 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player [OPEN] button Ejecting the Memory Stick Press the [OPEN] button. The front panel opens. Eject the Memory Stick. Lightly press the Memory Stick once. Memory Stick will not eject by itself. Lightly press the Memory Stick to eject. ● Do not drive with the front panel open. The panel may cause unexpected personal injury during a panic stop, or the like. ● Do not attempt to close the front panel by hand.
CD8445.book 95 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player Recording on Memory Stick Using ATRAC3 audio compression technology, this deck compresses the music data played on the built-in CD player, radio, external CD changer and other external inputs (such as portable players), and records the data on the MG Memory Stick. CDs being played on the deck can be recorded to a memory stick as digital data.
CD8445.book 96 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player [FUNC] button Insert the MG Memory Stick. When attempting to record from a CD, make sure to insert the CD. When attempting to record from the radio, etc., make sure to turn ON the desired sound source. Press the [FUNC] button for more than one second. Recording begins. When recording a music CD, the CD plays simultaneously. Press the [FUNC] button for more than one second. Recording stops.
CD8445.book 97 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player [FUNC] button [SEL] button [RTN] button Selecting tracks to be recorded The track to be recorded can be selected. Press the [FUNC] button for less than one second. The function mode is activated. Turn the [SEL] button to select Memory Stick. The selection item is highlighted. Press the [SEL] button. The Memory Stick setting mode is activated. Turn the [SEL] button to select REC Mode.
CD8445.book 98 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player [FUNC] button [SEL] button [RTN] button Setting sound quality The recording sound quality (the recording bit rate) can be set. The recording bit rate may be selected from 66k, 105k and 132k. Sound quality and data size increases as the bit rate increases. Press the [FUNC] button for less than one second. The function mode is activated. Turn the [SEL] button to select Memory Stick. The selection item is highlighted.
CD8445.book 99 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player [FUNC] button [SEL] button [RTN] button Turn the [SEL] button to select 66kbps, 105kbps or 132kbps. The selection item is highlighted. Press the [SEL] button. The selected settings will take effect. Press the [RTN] button. At this time, other adjustments can also be made in Memory Stick setting mode. Press the [RTN] button. At this time, other adjustments can also be made in function mode.
CD8445.book 100 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player [FUNC] button [SEL] button [RTN] button Deleting recorded file The recorded files being played back can be deleted. Press the [FUNC] button for less than one second, when the recording file being played back. The function mode is activated. Turn the [SEL] button to select Memory Stick. The selection item is highlighted. Press the [SEL] button. The Memory Stick setting mode is activated.
CD8445.book 101 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player [FUNC] button [SEL] button [RTN] button Turn the [SEL] button to select the file to be deleted. Press the [SEL] button. A message confirming file deletion will be displayed. Press the [SEL] button for more than two seconds. The selected file will be deleted. Press the [RTN] button. At this time, other adjustments can also be made in Memory Stick setting mode. Press the [RTN] button.
CD8445.book 102 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player [FUNC] button [SEL] button [RTN] button Formatting MG Memory Stick (quick format) MG memory stick can be formatted. Press the [FUNC] button for less than one second. The function mode is activated. Turn the [SEL] button to select Memory Stick. The selection item is highlighted. Press the [SEL] button. The Memory Stick setting mode is activated. Turn the [SEL] button to select Format.
CD8445.book 103 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Memory Stick player Press the [FUNC] or [RTN] button to exit function mode. ● Do not turn off the power or the ignition switch while formatting. The formatting process will be interrupted and the data may be corrupted. ● When a Memory Stick is formatted, all data on that Memory Stick will be erased. (Includes Memory Stick security recorded data and sound quality data) ● New MG Memory Stick may not be used without formatting.
CD8445.book 104 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner How to operate the tuner [ [FM AM] button ] button [SEL] button [ ] button First, press the [FM AM] button to start tuner operation. There are automatic and manual methods for setting stations in memory. The receiver will accept up to 24 stations in memory: 6 in AM and 18 in FM (6 each for FM1, FM2 and FM3.
CD8445.book 105 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner [FM AM] button Buttons [1] to [6] [SEL] button Entering stations into memory automatically (The automatic preset mode: ASM) Press the [FM AM] button for less than one second to switch to the desired FM or AM bands. Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button is pressed. Press the [SEL] button for more than two second until a VIII beep is heard. The automatic preset mode starts.
CD8445.book 106 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner [FM AM] button Buttons [1] to [6] [SEL] button Manually setting stations into memory This section covers the setting of stations in memory under the numbered buttons. Press the [FM AM] button for less than one second to switch between FM and AM. Turn the [SEL] button to the right or left to tune to the station to be entered in memory. Select any button, from [1] to [6], and press it for more than two seconds.
CD8445.book 107 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner Buttons [1] to [6] [SEL] button Preset station scan This function enables reception of all the stations in the preset buttons for five seconds each. Press the [SEL] button for less than two seconds. [P SCAN] will appear on the display, and stations stored under preset buttons [1] through [6] will be played for five seconds each. To stop the preset scan mode at a desired station, press the [SEL] button again.
CD8445.book 108 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner [FUNC] button [SEL] button [ [ ] button ] button [RTN] button Setting a station name Station name settings can be changed. Press the [FUNC] button for less than one second while in the tuner mode. The function mode is activated. Turn the [SEL] button to select Station Name. The selected item will be highlighted. Press the [SEL] button. The station name setting mode is activated.
CD8445.book 109 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner [FUNC] button [SEL] button [RTN] button Turn the [SEL] button to the left or right to select characters and press the [SEL] button. Turn to the right: Advances the character forward in its type. Turn to the left: Moves the character backward in its type. [Upper-case alphabet characters] Initial value [A] A¡B¡C¡...X¡Y¡Z [Numeric characters] Initial value [1] 1¡2¡3¡...
CD8445.book 110 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner [FUNC] button Button [6] [RTN] button Deleting a station name Press the [FUNC] button for less than one second while in the tuner mode. The function mode is activated. Turn the [SEL] button to select Station Name. The selected item will be highlighted. Press the [SEL] button. The station name that is displayed at this point will be deleted. Hold the [6] button down for more than two seconds.
CD8445.book 111 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner [FM AM] button Button [1] Changing the reception sensitivity for automatic scanning The deck lets you select the reception sensitivity to be used for automatic scanning of stations. The two sensitivity modes available for this deck are AUTO mode and DX mode. When an optional HD Radio tuner unit is connected, reception sensitivity is set to the AUTO Mode. The DX Mode is unavailable. (U.S.A.
CD8445.book 112 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner [FM AM] button Button [3] Changing the radio band location The location for the radio bands used between the North American region and the Asia/Australia/Latin region can be switched. The default setting is USA (North America). When an optional HD Radio tuner unit is connected, radio band location is set to USA. Other radio band locations are unavailable. (U.S.A. only) Check that the deck is in standby mode.
CD8445.book 113 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner FM reception characteristics In general, FM has much better tonal quality than AM. However, FM and FM stereo reception encounter several characteristic problems not encountered with AM. FM is more difficult to receive than AM in a moving vehicle. The following are explanatory notes on what to expect from FM reception and on how to get satisfactory performance.
CD8445.book 114 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner Reception area of FM broadcasts A home receiver can catch weak FM stereo signals through the use of a tall, directional or ultra-sensitive antenna. In a moving vehicle, the area for good reception is limited because of varying conditions encountered while driving, including the types and heights of broadcast antenna structures, signal strength, engine noise, etc.
CD8445.book 115 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode How to operate the Sound Adjustment Mode About Sound Adjustment Mode This deck is equipped with two different sound adjustment modes: normal mode and advance mode. In normal mode, the acoustic characteristics inside the vehicle can be adjusted using comparatively simple settings. In addition, it corresponds to basic sound systems which comprise front speakers, rear speakers, and subwoofer.
CD8445_09_E.fm 116 ページ ２００４年１２月１６日 木曜日 午後４時５７分 How to operate the Sound Adjustment Mode Position selector When the position of the listener's seat is selected, the time taken for the sound to travel from the speakers to the listener can then be adjusted in order to obtain a more natural sound orientation. This unit allows up to four different positions to be set.
CD8445.book 117 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode An "equalizer" is a function that corrects these peaks and dips in order to flatten the frequency characteristics. However with a normal graphic equalizer, the median frequency and the Q (sharpness and band width) are fixed, so that when neighboring bands are corrected, there is a limit to the amount by which distortion in the peak and dip characteristics can be corrected.
CD8445.book 118 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode Time Alignment With vehicle audio systems, the installation position of the speakers and the position of the listener mean that the distances from the listener to the left and right speakers are almost always different. These differences in the distance from the listener to each speaker in turn means that the time taken for the sound to reach the listener is different for each speaker.
CD8445.book 119 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode Crossover The frequency band that is stored by audio media such as CDs is a fairly wide range from 20 Hz to 20 kHz, and it is difficult for a single speaker to be able to play back all frequencies in such a wide range. Because of this, several speakers can be used, with different frequency bands (such as treble, medium and bass) allotted to each speaker so that wide frequency ranges can be played back.
CD8445.book 120 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode ● A low-pass filter (LPF) is a filter that cuts out frequencies that are higher than the specified frequency (treble range) and allows lower frequencies (bass range) to pass through. ● The slope is the signal level at which frequencies that are one octave higher or one octave lower are dampened. The larger the slope value, the greater the slope.
CD8445_09_E.fm 121 ページ ２００４年１２月１６日 木曜日 午後４時５８分 How to operate the Sound Adjustment Mode Non-fader phase The sounds that are output from woofers include sounds that are in the same frequency ranges that are output from the front and rear speakers, and under the various conditions that can occur inside vehicle compartments, some of these sounds may cancel each other out. This phenomenon can be eliminated by changing the phase of the woofer.
CD8445.book 122 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode ● Automatic parametric equalizer (Advance Mode Only) This can be used to automatically correct distortion in frequency characteristics (peaks and dips) based on the results of measuring the frequency characteristics inside the vehicle. Automatic parametric equalizer correction is carried out in the following steps.
CD8445.book 123 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode ● Time alignment and crossover adjustment Other adjustments besides adjustment of this deck can be carried out using the ECLIPSE web site. The procedure for doing this is displayed on the screen, and adjustment is comparatively easy using this method. Access the ECLIPSE website and follow the instructions that appear on the screen.
CD8445.book 124 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button Operations during Normal Mode Press the [SOUND] button. The mode will change to sound adjustment mode (normal mode). Refer to "Operations during Advance Mode" on page 131 for details on the operating the Advance Mode. If you press the [SOUND] button during sound adjustment mode, the adjustment mode is canceled and the mode returns to normal music mode.
CD8445.book 125 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button DSP Setting The DSP feature adds reverberations to simulate ambience in different types of surroundings (room size). Turn the [SEL] button to select DSP. Press the [SEL] button. The DSP mode is activated. Turn the [SEL] button to select the room size. When the button is turned, the setting item changes in the following order.
CD8445.book 126 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Position selector setting (POSITION) When the position of the listener's seat is selected, the time taken for the sound to travel from the speakers to the listener can then be adjusted in order to obtain a more natural sound orientation. This deck allows up to four different positions to be set. Turn the [SEL] button to select POSITION. Press the [SEL] button.
CD8445.book 127 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Non-fader phase selection (Non-F Phase) The merging of sound between the front and rear speakers and the woofer can be improved by selecting the phase. Switch the phase to a phase which lets the speakers combine without any disharmony. Turn the [SEL] button to select Non-F Phase. Press the [SEL] button. The mode will change to phase selection mode.
CD8445.book 128 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [ [ ] button ] button [RTN] button Crossover adjustment (X-Over) The frequencies for the front and rear speaker high-pass filter (HPF) and woofer low-pass filter (LPF) can be set within a range of 63 to 200 Hz. (This is the same as the HPF and LPF cutoff frequencies.) Turn the [SEL] button to select X-Over. The selected item will be highlighted. Press the [SEL] button.
CD8445.book 129 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Multi-harmonizer settings (Harmonizer) This function uses harmonic synthesis to restore the high-frequency component that is lost as a result of the compression process so that fresher sound can be obtained during MP3 /WMA, Memory Stick (ATRAC3) playback. Turn the [SEL] button to select Harmonizer. The selected item will be highlighted. Press the [SEL] button.
CD8445.book 130 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Non-Fader Output Non-Fader Output can be stereo or mono. Select the method that matches the output method for the sub-woofer system that is connected to the deck. Turn the [SEL] button to select Non-F Output. The selected item is highlighted. Press the [SEL] button. The mode will change to Non-F Output. Turn the [SEL] button to select Stereo or Monaural.
CD8445.book 131 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button Operations during Advance Mode Press the [SOUND] button. The mode will switch to sound adjustment mode (normal mode). Press the [SOUND] button for more than two seconds. The mode switches between normal mode and advance mode each time the button is pressed. During advance mode, "ADVANCE MODE ON" and the scroll display appear in the display.
CD8445.book 132 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [ ] button [SEL] button SRS Circle Surround II (CS II) The system achieves surround sound by combining SRS TruBass, which uses the difference between two different frequencies to boost bass tones, and SRS Circle Surround, which uses 2ch (L/R) correlation to expand the sound. Setting CSII modes Turn the [SEL] button to select CSII. The selected item is highlighted. Press the [SEL] button.
CD8445.book 133 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SEL] button [ ] button [ ] button Parametric equalizer adjustment (PEQ) The parametric equalizer adjusts 7 frequency bands. Turn the [SEL] button to select PEQ. The selected item is highlighted. Press the [SEL] button. The mode will change to parametric equalizer adjustment mode. Press the [SEL] button to select the band to be adjusted.
CD8445.book 134 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button Buttons [1] to [6] [RTN] button Press the [6] button to select the Q curve pattern. Each time the button is pressed, the Q curve changes in the following order. NORMAL SHARP SLOW Repeat the operations in steps change the settings for each band. to to Hold down a button, [1] to [5], for more than two seconds to preset a value.
CD8445.book 135 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button Buttons [1] to [5] [RTN] button Selecting an equalizer mode from memory Press a preset button to select the equalizer mode set in memory for the button. The buttons that set equalizer modes in memory are called preset buttons. Turn the [SEL] button to select PEQ. Press the [SEL] button. Select any button, from [1] to [5], and press it for less than two seconds.
CD8445.book 136 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SEL] button Measuring/display frequency characteristic Frequency characteristics inside the vehicle can be measured and displayed on the display. The measurement result can be referred to when adjusting parametric equalizer. This result is also necessary to automatically correct parametric equalizer setting using E-iSERV sound effect customizations.
CD8445.book 137 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [OPEN] button [RTN] button [AUDIO CONTROL] button Press the [AUDIO CONTROL] button for less than two seconds. After pushing the button, a 10-second countdown begins. Leave the vehicle during that time. Pink noise will be output from the speakers and measurement of the frequency characteristics will start. [Measuring] will appear on the display while measurement is in progress.
CD8445.book 138 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode Press the [RTN] button. At this time, other adjustments can also be made in advance mode. Press the [SOUND] or [RTN] button to exit sound adjustment mode. ● Sound quality data is written to Memory Stick as follows. MSFTEN SOUND 205 000.
CD8445.book 139 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SEL] button Simplified time alignment settings (Time Alignment) This function corrects the position characteristics and frequency characteristics in order to delay the signals being output from the various speakers so that the signals from each speaker reach the listening position at the same time. ● Time Alignment cannot be operated when the CSII is ON. ● Before selecting a position, make sure that CSII is OFF.
CD8445.book 140 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Position selector setting (Position) When the position of the listener's seat is selected, the time taken for the sound to travel from the speakers to the listener can then be adjusted in order to obtain a more natural sound orientation. This deck allows up to four different positions to be set. Turn the [SEL] button to select Position. The selected item will be highlighted.
CD8445.book 141 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Selecting the type of vehicle (Car Type) You can select the time alignment settings to match your vehicle from a range of preset settings for different types of vehicle, allowing you to select the optimum time alignment settings automatically. Turn the [SEL] button to select Car Type. The selected item will be highlighted. Press the [SEL] button.
CD8445.book 142 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode Turn the [SEL] button to select the setting item. When the button is turned, the setting item changes in the following order and the selected item is highlighted. Compact Sedan Wagon Mini Van SUV Truck Press the [SEL] button. The selected settings will take effect. Press the [RTN] button. Other time alignment items can be set at this time. Press the [RTN] button.
CD8445.book 143 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Tweeter settings (Tweeter) You can select the tweeter installation location and whether or not a tweeter is being used or not, allowing you to select the optimum time alignment settings automatically. Turn the [SEL] button to select Tweeter. The selected item will be highlighted. Press the [SEL] button. The mode will change to tweeter setting mode.
CD8445.book 144 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Rear speaker position selection (Rear SP) You can select the rear speaker installation location, allowing you to select the optimum time alignment settings automatically. Turn the [SEL] button to select Rear SP. The selected item will be highlighted. Press the [SEL] button. The mode will change to rear speaker position setting mode.
CD8445.book 145 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [ [ ] button ] button [RTN] button Crossover adjustment (X-Over) The frequencies for the front and rear speaker high-pass filter (HPF) and woofer low-pass filter (LPF) can be set within a range of 63 to 200 Hz. (This is the same as the HPF and LPF cutoff frequencies.) Turn the [SEL] button to select X-Over. The selected item will be highlighted. Press the [SEL] button.
CD8445.book 146 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Multi-harmonizer settings (Harmonizer) This function uses harmonic synthesis to restore the high-frequency component that is lost as a result of the compression process so that better sound can be obtained during MP3 /WMA or Memory Stick (ATRAC3) playback. Turn the [SEL] button to select Harmonizer. The selected item will be highlighted. Press the [SEL] button.
CD8445.book 147 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Non-fader phase selection (Non-F Phase) The merging of sound between the front and rear speakers and the woofer can be improved by selecting the phase. Switch to a phase which lets the speakers combine without any disharmony. Turn the [SEL] button to select Non-F Phase. The selected item will be highlighted. Press the [SEL] button.
CD8445.book 148 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button [RTN] button Non-Fader Output Non-Fader Output can be stereo or mono. Select the method that matches the output method for the sub-woofer system that is connected to the deck. Turn the [SEL] button to select Non-F Output. The selected item is highlighted. Press the [SEL] button. The mode will change to Non-F Output. Turn the [SEL] button to select Stereo or Monaural.
CD8445_09_E.fm 149 ページ ２００４年１２月１６日 木曜日 午後５時２５分 How to operate the Sound Adjustment Mode [SOUND] button [SEL] button Button [1] to [5] [RTN] button Importing Sound Data Sound data adjusted by the E-iSERV website can be downloaded to a CD-R or a Memory Stick and imported into the deck. Turn the [SEL] button to select Sound Data. The selected item is highlighted. Press the [SEL] button. The mode will change to Sound Data mode. Turn the [SEL] switch to select media types.
CD8445.book 150 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the Sound Adjustment Mode Press the [RTN] button. At this time, other adjustments can also be made in advance mode. Press the [SOUND] or [RTN] button to exit sound adjustment mode. When using a Memory Stick: ● Sound quality data is written to Memory Stick as follows. MSFTEN DATA 204 000.
CD8445.book 151 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the AREA SHOT function (U.S.A. only) How to operate the AREA SHOT function (U.S.A. only) About the AREA SHOT Using AREA SHOT function, maps to destinations and guidance information can be displayed on your deck if you have set route on the ECLIPSE web site (E-iSERV). Current vehicle position can also be displayed on the map if an optional GPS unit is connected. The display in this manual may differ from that of the accrual product.
CD8445.book 152 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the AREA SHOT function (U.S.A. only) To use the AREA SHOT function In order to use AREA SHOT, driving instructions such as the direction of travel and the street names of turn intersections must be downloaded from the ECLIPSE website (E-iSERV) and imported into the CD8445. The process is as follows: Access The ECLIPSE Website. (URL: http/www.e-iserv.jp) Register as a user. A User Registration Key is required when registering.
CD8445_10_E.fm 153 ページ ２００４年１２月１６日 木曜日 午後５時３８分 How to operate the AREA SHOT function (U.S.A. only) Map data The map data used by the deck was created based on information provided by Tele Atlas and Geographic Data Technology. When using the map data, be aware actual road conditions and obey traffic rules. Copying, publishing or using maps in electronic media without express written consent is forbidden.
CD8445.book 154 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the AREA SHOT function (U.S.A. only) [OPEN] button [FUNC] button [SEL] button Reading the AREA SHOT data The AREA SHOT data that has been downloaded from E-iSERV (web site) to a Memory Stick or CD-R can be loaded into the deck and saved there. Press the [FUNC] button for less than one second. The function mode is activated. Turn the [SEL] button to select AreaShot. Press the [SEL] button. The media selection screen appears.
CD8445.book 155 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the AREA SHOT function (U.S.A. only) Turn the [SEL] button to select the saving file. The selection file name is highlighted. Press the [SEL] button. The selected file will be saved. "READING" is displayed while data is being imported. When reading has finished, [Completed] will appear on the display and then it will return to the display for selecting the function mode.
CD8445.book 156 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the AREA SHOT function (U.S.A. only) [ [MUTE] button ] button [RTN] button [DISP] button [ ] button Changing the AREA SHOT mode Press the [MUTE] button for more than one second. Guidance point maps, intersection street names and turning directions are displayed on the screen. Pressing and holding the [MUTE] button (for 1 second or more) a second time closes the Area Shot mode.
CD8445.book 157 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the AREA SHOT function (U.S.A. only) Using the AREA SHOT mode By manually switching between guidance points, both previous and next guidance points can be confirmed during guidance. AREA SHOT Screen Configuration Guidance information: Information about guidance points (traveling direction, street names) displayed as a text. Arrows: Indicates direction to the guidance point.
CD8445.book 158 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the AREA SHOT function (U.S.A. only) [ [ ] button ] button Switching between guidance points After passing each location described in the guidance, it is necessary to switch manually to the next guidance screen. The previous screen can also be accessed manually and confirmed. Press [ points. ] and [ ] to switch between guidance [ ]............. To switch to the next guidance point. [ ].............
CD8445.book 159 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the AREA SHOT function (U.S.A. only) [DISP] button [RTN] button Re-scrolling through text information Text information including intersection street names and turn directions can be scrolled across the screen by switching through guidance points. A maximum of 11 characters can be displayed on a single screen. Excess characters are scrolled on the display.
CD8445_10_E.fm 160 ページ ２００４年１２月１６日 木曜日 午後５時２７分 How to operate the AREA SHOT function (U.S.A. only) Changing AREA SHOT screens Press the [RTN] button. In the AREA SHOT mode, the audio screen can be accessed. Pressing the button repeatedly allows you to switch back and for the between the AREA SHOT screen and the Audio screen. When a GPS unit is connected, the following operations are available.
CD8445.book 161 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the AREA SHOT function (U.S.A. only) Display Arrows Arrows for indicating turn directions are displayed as follows.
CD8445.book 162 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to use the remote control How to use the remote control Precautions in use of the remote control ● Be careful when handling the control, especially because it is small and light. Dropping or striking it hard may damage it, wear out the battery or cause a malfunction. ● Keep the remote control free of moisture, dust and water. Do not subject it to shock.
CD8445.book 163 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to use the remote control [PWR] button Remote-control light receptor [ ] button [MUTE] button [ ] button Turning the power on/off When the power is turned on, the state used when the power was turned off such as CD and tuner playing is restored. Press the [PWR] button. The power turns on or off each time the button is pressed. When the main unit is shut down, the remote control will not work. Adjusting the audio volume Press the [ ] or [ ] button.
CD8445.book 164 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to use the remote control [MODE] button [DISC] button [AUX] button [TU] button [BAND] button Switching playback modes Press the [MODE] button. Press the button to switch modes in the following sequence: Tuner Disc Memory Stick AUX Modes can be switched by pressing the following buttons: [TU] button: The tuner mode is activated. [DISC] button: The disc mode is activated. [AUX] button: The AUX mode is activated.
CD8445.book 165 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to use the remote control [DISC] button [BAND] button [ PRESET CH buttons ] [ TUNE SEEK buttons ] Selecting a station (manually or automatically) A short press of the button will allow manual station tuning. Pressing for more than one second will start automatic tuning. Press the [ TUNE•SEEK ] button. [ ] button: Tunes to higher frequency stations. [ ] button: Tunes to lower frequency stations.
CD8445.book 166 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to use the remote control [BAND] button [MUTE] button [ DISC ] buttons [ TRACK buttons ] Advancing to the next track or returning to the beginning of the track being played Press the [ [ [ TRACK ] button. ] button: Advances to the next track. ] button: Returns to the beginning of the track being played. (Press repeatedly to move to previous tracks.) Hold the [ ] button down to fast forward, or the [ through the track being played.
CD8445.book 167 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to use the remote control [BAND] button [MUTE] button [ DISC ] buttons [ TRACK buttons ] How to play MP3/WMA Switching disc modes Press the [DISC] buton. The disc mode is activated. Press the [BAND] or [DISC] button. When one or two CD changers are connected, press the [BAND] or [DISC] button to change modes from CD player ➔ CD changer 1 ➔ CD changer 2. The indicator will skip a changer or player that has no discs loaded.
CD8445_11_E.fm 168 ページ ２００４年１２月１６日 木曜日 午後５時３９分 How to use the remote control Replacing the battery To prevent accidents, store batteries out of the reach of children. If a child has swallowed one, consult a doctor immediately. Use two AAA size batteries. Remove the back cover of the remote control unit by gently pressing and sliding it in the direction indicated by the arrow. Install the two batteries provided into the compartment as illustrated inside the compartment.
CD8445.book 169 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to use the remote control ● Be extremely careful not to swallow the battery. ● The battery life is approximately one year. If the remote control unit does not operate correctly or if the button lamp gets dim, replace the batteries. ● Be sure to orient the batteries correctly so that the positive and negative poles match the diagram. ● Do not use one new battery and one old one; use two new batteries. ● Use only two of the same kind of battery.
CD8445.book 170 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the receiver with an optional CD changer connected How to operate the receiver with an optional CD changer connected [DISC MS] button [SEL] button This section covers the operation of an optional CD changer that is connected to the receiver. To switch from another mode, press the [DISC MS] button for less than one second. Listening to a CD Press the [DISC MS] button for less than one second.
CD8445.book 171 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the receiver with an optional CD changer connected [4 SCAN] button [ ] button [ ] button Fast Forward/Rewind Fast forward or rewind the song currently being played. Press and hold the [ [ ] button: [ ] button: ] or [ ] button. Fast forward. Rewind. Playing the beginning of tracks (SCAN) Press the [4 SCAN] button.
CD8445.book 172 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the receiver with an optional CD changer connected [5 RPT] button [6 RAND] button Repeating the same track (REPEAT) Press the [5 RPT] button. Pressing on the button for less than one second causes the changer to repeat the track currently being played, until the button is pressed again. Hold the button until the [ALL REPEAT] display appears to repeat all tracks on the CD being played.
CD8445.book 173 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the receiver with an optional CD changer connected [SEL] button Buttons [1 ] and [2 ] Buttons [1] to [6] Skipping to the next or previous CD Press button [1 Button [1 Button [2 ] or [2 ]. ]: Selects the next lower number disc. ]: Selects the next higher number disc. Specifying a CD to play A CD of your choice is directly selectable out of the loaded discs. Press the [SEL] button for less than one second.
CD8445.book 174 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only) How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only) About HD Radio If the optional HD Radio (High Definition Radio) tuner unit is connected, terrestrial digital broadcasts can be received. When terrestrial digital broadcasts are received, FM reception has the same quality as a CD, and AM reception has the same quality as conventional FM sound.
CD8445.book 175 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only) [ ] button [FM AM] button [SEL] button [ ] button First, press the [FM AM] button to start tuner operation. There are automatic and manual methods for setting stations in memory. The receiver will accept up to 24 stations in memory: 6 in AM and 18 in FM (6 each for FM1, FM2 and FM3.
CD8445.book 176 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only) [FM AM] button Buttons [1] to [6] [SEL] button Entering stations into memory automatically (The automatic preset mode: ASM) Press the [FM AM] button for less than one second to switch to the desired FM or AM bands. Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button is pressed.
CD8445.book 177 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only) [FM AM] button Buttons [1] to [6] [SEL] button Manually setting stations into memory This section covers the setting of stations in memory under the numbered buttons. Press the [FM AM] button for less than one second to switch between FM and AM.
CD8445.book 178 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only) Buttons [1] to [6] [SEL] button Preset station scan This function enables reception of all the stations in the preset buttons for five seconds each. Press the [SEL] button for less than two seconds. [P SCAN] will appear on the display, and stations stored under preset buttons [1] through [6] will be played for five seconds each.
CD8445_13_E.fm 179 ページ ２００４年１２月１３日 月曜日 午後８時２９分 How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only) [FUNC] button [SEL] button [DISP] button [RTN] button Switching between displays when receiving HD Radio During digital reception, the name of the station being received and other information can be displayed. Press the [DISP] button for more than one second.
CD8445.book 180 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only) [FUNC] button [SEL] button [DISP] button [RTN] button Turn the [SEL] button to select AUTO or OFF. The selected item will be highlighted. In the [AUTO] setting, the selection is switched between digital and analog reception automatically. In areas where digital reception is not possible, reception is automatically switched to analog to avoid loss of reception.
CD8445.book 181 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) About SIRIUS satellite radio If the optional SIRIUS satellite radio tuner unit is connected, satellite radio broadcast can be received. With SIRIUS satellite radio, over 100 channels are available including music, sports, news, and entertainment programs.
CD8445.book 182 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) [ ] button [FM AM] button [SEL] button [ ] button The receiver will accept up to 24 stations in memory. Selecting the radio mode Press the [FM AM] button for more than one second. The mode switches between satellite radio mode and FM/AM radio mode each time the button is pressed.
CD8445_14_E.fm 183 ページ ２００４年１２月１６日 木曜日 午後５時２７分 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) [SEL] button [ ] button [ ] button Category selection The channel can be selected from among categories such as POP and ROCK. Consult the SIRIUS website for details of categories. Press the [ ] or [ ] button for more than one second. Categories will switch in order shown below each time button is pressed. [ ] button .............. Advance to next category.
CD8445.book 184 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) Buttons [1] to [3] Button [5] Press the buttons [1], [2] and [3] to select the channel number to be input. [1] button. . . . . Hundreds [2] button. . . . . Tens [3] button. . . . . Units Each time the buttons are pressed, the numerals change in the following order. 0➔1➔2➔3➔4➔5➔6➔7➔8➔9 Pressing the [6] button clears the numeral at the previous digit.
CD8445.book 185 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) [FM AM] button Buttons [1] to [6] [SEL] button Manually setting channels into memory This section covers the setting of channels in memory under the numbered buttons. Turn the [SEL] button to the right or left to tune to the channel to be entered in memory. Select any button, from [1] to [6], and press it for more than two seconds.
CD8445.book 186 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) Buttons [1] to [6] [DISP] button [SEL] button Preset channel scan This function enables reception of all the channels in the preset buttons for five seconds each. Press the [SEL] button for less than two seconds. [P SCAN] will appear at the display, and channels stored under preset buttons [1] through [6] will be played for five seconds each.
CD8445.book 187 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Others Others [DISC] button Connecting portable audio players to the AUX jack Use a commonly available accessory cord with the RCA connector to connect a portable audio player to the AUX (auxiliary) jack of this system. Turn on the portable audio player and start its play function. Switch to AUX mode by pressing the [DISC] button for more than one second.
CD8445.book 188 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Others [FUNC] button [SEL] button [RTN] button Changing auxiliary input sensitivity The sensitivity of the auxiliary mode can be changed. Press the [FUNC] button for less than one second. The function mode is activded. Turn the [SEL] button to select AUX Sensitivity. The selected item is highlighted. Press the [SEL] button. The AUX sensitivity mode is activdted. Turn the [SEL] button to select the sensitivity mode.
CD8445.book 189 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Others [DISP] button User Registration Key display User Registration Key is your CD8445's unique ID. In order to use the ECLIPSE website (E-iSERV), a 16-digit User Registration Key is necessary. Check that the deck is in standby mode. Press the [DISP] button for more than one second. The first 8 digits of your User Registration Key will be displayed. Press and hold [DISP] once more (for a second or more) and the remaining 8 digits will be displayed.
CD8445.book 190 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 If you have a question: If you have a question: [RESET] button First check the item mentioned below before attempting to troubleshoot problems. If a problem occurs, for instance when the unit does not respond to any button presses, or the display doesn't work correctly, press the [RESET] button using a paper clip or similar item. Pressing the [RESET] button will delete all the entries from memory.
CD8445.book 191 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 If you have a question: Displayed information (for troubleshooting) The information listed in the chart below is displayed to show the status of the CD, Memory Stick player, Area Shot function, Sirius Radio and CD changer. Refer to the chart for the appropriate action. Information Contents Explanation and remedial action to take INFO 2 NO DISC LOADED IN THE MAGAZINE There is no disc in the magazine or player. Load a disc in the magazine.
CD8445_16_E.fm 192 ページ ２００４年１２月１６日 木曜日 午後５時２８分 If you have a question: MSINFO 5 YOU TRIED TO RECORD MORE THAN THE MAXIMUM NUMBER OF TRACKS (400) ONTO A MG MEMORY STICK Delete some of the MG Memory Stick data or use a different MG Memory Stick for recording. MSINFO 6 AN INCOMPATIBLE MEMORY STICK HAS BEEN INSERTED Check that the Memory Stick can be used with this deck. MSINFO 7 MG MEMORY STICK CONTAINING NO MUSIC DATA HAS BEEN INSERTED Insert a MG Memory Stick containing music data.
CD8445.book 193 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 If you have a question: Mode Problem Dead or weak sound Power does not turn on. Common to all Frequencies or titles set in memory are deleted. No guide tone sounds. The remote control does not work. Remedial action to take Causes Refer to page Is the volume control up sufficiently? Turn up the volume control. 45 Is the muting function in effect (MUTE)? Cancel the muting (MUTE) function.
CD8445.book 194 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 If you have a question: Mode Problem The disc cannot be inserted. The disc is ejected as soon as it is inserted. Or, the disc cannot be ejected. The disc cannot be changed. Causes Is an extra label or seal applied to the disc? Are there rough edges, deformations or damaged areas on the disc? Is the disc damaged? CD Sound skips around. Sound is intermittent. Sound is bad in quality. The disc cannot be ejected.
CD8445_17_E.fm 195 ページ ２００４年１２月１３日 月曜日 午後１時３７分 Specifications Specifications Power Supply Current Drain Dimensions (W x H x D) In-Dash Unit Mass (weight) Usage temperature range Storage temperature range 14.4V DC (11-16V) 3A 7" x 2" x 6-1/8" (178 x 50 x 155mm) Approx. 1.7kg -20°C to +65°C (-4°F to +149°F ) -40°C to +85°C (-20°F to +185°F ) Frequency Range USA: Asia: Australia: Latin America: Usable Sensitivity 50dB Quieting Sensitivity Frequency Response Stereo Separation 87.
CD8445_17_E.fm 196 ページ ２００４年１２月１３日 月曜日 午後１時３７分 Specifications Frequency Response S/N Ratio (A-weighted) Total Harmonic Distortion 20Hz~20kHz ±3dB 100dB 0.008 %
CD8445.book 197 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Before installation Before installation ● Note ● Be sure to disconnect the vehicle battery's negative terminal before installing the receiver. Components No.
CD8445.book 198 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 Mounting instruction Mounting instruction Mounting the main unit –If installing the main unit by the mounting sleeve– Insert the mounting sleeve into the opening in the vehicle dash board or console box. Use a screwdriver or the like to bend the tabs in the mounting sleeve to secure the mounting sleeve. BEND THE MOUNTING TABS. DASH BOARD OR CONSOLE BOX 2 MOUNTING SLEEVE Attach the side brackets to the main unit using flathead screws.
CD8445_19_E.fm 199 ページ ２００５年１月２６日 水曜日 午後２時４８分 Mounting instruction Mount the stud bolt to the main unit. Insert the main unit into the mounting sleeve until it locks in place. Fasten the rear of the main unit using either method [A] or [B]. Some automobiles may be equipped to secure the back of the main unit using the stud bolt and supplied rubber support. Select method [A] or [B] to suit the interior configuration of the vehicle. Install the bezel on the main unit.
CD8445_19_E.fm 200 ページ ２００５年１月２６日 水曜日 午後２時４８分 Mounting instruction –If installing the main unit by the side brackets of the vehicle– Remove the pockets and any other accessories from the center cluster to make room for the main unit. Remove the mounting side brackets for the pocket. CENTER CLUSTER POCKET SCREWS Attach the side brackets to the main unit. Install the main unit in the vehicle.
CD8445_19_E.fm 201 ページ ２００５年１月２６日 水曜日 午後２時４８分 Mounting instruction Names of lead wires and destinations (refer to Page 204) ● Caution ● Never connect the power supply to the speaker leads, otherwise it causes damage to the main unit. ● Note ● To prevent unconnected leads from shorting out, insulate them by wrapping their tips with electrical tape. Similarly, insulate the ends of connected leads.
CD8445_19_E.fm 202 ページ ２００５年１月２６日 水曜日 午後２時４８分 Mounting instruction No. Name 12 AUX in terminals Wire color Destination Connect to an external voice output terminal. If the microphone for measuring frequency characteristics is used, connect microphone to the L side of the RCA terminal. 13 LAN terminals Connect to the LAN terminal of the GPS unit. 14 Genuine steering remote control terminal Connect to the vehicle steering remote control.
CD8445_19_E.fm 203 ページ ２００５年１月２６日 水曜日 午後２時４８分 Mounting instruction System Note: Adjust the external amplifier’s input level.
ページ ２００５年１月２６日 水曜日 204 White(+) Brown/Black Brown Purple/Black(-) Purple(+) Green/Black(-) Green(+) Gray/Black(-) Gray(+) 14 TO STEERING REMOTE CONTROL RR RL FR FL ANTENNA PLUG White/Black(-) 16P 8 FRONT 9 REAR 10 NON-FADER Never connect the power supply to the speaker leads, otherwise it causes damage to the main unit.
ページ ２００５年１月２６日 水曜日 8P 205 White(+) Brown/Black Brown Purple/Black(-) Purple(+) Green/Black(-) Green(+) Gray/Black(-) Gray(+) White/Black(-) 16P 14 TO STEERING REMOTE CONTROL RR RL FR FL ANTENNA PLUG 8 FRONT 9 REAR 10 NON-FADER Never connect the power supply to the speaker leads, otherwise it causes damage to the main unit.
ページ ２００５年１月２６日 水曜日 午後２時４８分 206 (B) (A) 3 TO GROUND 6 TO TURN ON LEAD OF EACH UNIT (supply) 5 TO HEAD LIGHT SWITCH (supply) 4 TO POWER ANTENNA RELAY (supply) 1 TO ACC (Power supply) 2 TO BATTERY+12V (Permanent supply) Blue Red 13 Black Blue/White Orange/White Yellow 13P CD8445 R SIDE L SIDE White(+) 14 TO STEERING REMOTE CONTROL WIRE WITH TAPE 11 INSULATE EACH WIRE WITH TAPE 11 INSULATE EACH INTERCONNECTING CABLE Brown/Black Brown Purple/Black(-) Purple(+) Green/Black(-
ページ ２００５年１月２６日 水曜日 午後２時４８分 13P 207 2P 13P CH3083 1 TO ACC (Power supply) 2 TO BATTERY+12V (Permanent supply) 3 TO GROUND 6 TO TURN ON LEAD OF EACH UNIT (supply) 5 TO HEAD LIGHT SWITCH (supply) Black Blue/White Orange/White Blue Red 13 R SIDE Yellow 13P CD8445 4 TO POWER ANTENNA RELAY (supply) ANTENNA EXTENSION CABLE ANTENNA PLUG VRM803 14 TO STEERING REMOTE CONTROL WIRE WITH TAPE 11 INSULATE EACH WIRE WITH TAPE 11 INSULATE EACH INTERCONNECTING CABLE Brown/Black Brown
２００４年１２月１３日 月曜日 午前１１時３０分 208 1 TO ACC (Power supply) 3 TO GROUND 6 TO TURN ON LEAD OF EACH UNIT (supply) 5 TO HEAD LIGHT SWITCH (supply) Blue Red 13 Black Blue/White Orange/White Yellow 13P CD8445 4 TO POWER ANTENNA RELAY (supply) CH3083 2 TO BATTERY+12V (Permanent supply) 9 REAR 8 FRONT INTERCONNECTING CABLE 14 TO STEERING REMOTE CONTROL WIRE WITH TAPE 11 INSULATE EACH WIRE WITH TAPE 11 INSULATE EACH ANTENNA PLUG VRM803 Brown/Black Brown Purple/Black(-) Purple(+) Green/Black
CD8445.book 209 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to contact customer service How to contact customer service Should the product require service, please contact your nearest Eclipse dealer. DIVISION OF FUJITSU TEN CORP. OF AMERICA 19600 SOUTH VERMONT AVENUE, TORRANCE, CA 90502 Phone: (310) 327-2151 FUJITSU TEN (AUSTRALIA) PTY LTD. ECLIPSE AUSTRALIA Phone: 1800-211-411 Cobra Malaysia Sdn, bhd. Level 5, Axis Plaza, Jalan U1/44, Glenmarie, 40150 Shah Alam, Selangor D.
CD8445.book 210 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 How to contact customer service Transpectra Co., LTD. 115-16 nonhyun dong kangnam ku Seoul, Korea. Phone: 02-540-4595 Fax: 02-2-540-4666 HYUNDAI AUTONET Co., Ltd. 1st FL. Namhyoung Bldg, 746-23 Yeoksam-Dong, Kangnam-Ku, Seoul, Korea 135-080 Phone: 02-508-6001 Fax: 02-2-508-6067 Sentrek Taiwan, LTD. 1, 9F, Lane 155, Section 3, Peishen RD., Shenkeng, Taipei Hsien, 222 Taiwan, R.O.C. Phone: 02-2662-8110 Fax: 02-2662-8117 Sho-Ten Co.
CD8445.book 211 ページ ２００４年１２月１３日 月曜日 午前１１時３０分 IMPORTANT RECORD YOUR “KEY CD” OR “MEMORY STICK (SECURITY CODE)” HERE… STORE YOUR “KEY CD” OR “MEMORY STICK (SECURITY CODE)” ALONG WITH YOUR OWNER’S MANUAL.
CUSTOMER NOTICE Please retain this booklet and write in the serial number of your CD8445 for identification. The serial number is labeled or stamped on the chassis. Serial No. FUJITSU TEN LIMITED Contact:FUJITSU TEN CORP. OF AMERICA 19600 So. Vermont Avenue, Torrance, CA 90502 Call:800-233-ECLIPSE www.eclipse-web.com "ECLIPSE" is a registered trademark of FUJITSU TEN LIMITED in 48 countries including the U.S. and Japan. 090001-1468A700 0504 (F.
