AutoScan AutoScan Satellite System 9630 9630-LP Installation and Operating Instructions ® Satellite Solutions for Mobile Markets 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.
IMPORTANT! The satellite TV market is expanding and changing. The information in this manual was accurate at the time of printing. If your King-Dome does not operate as outlined in this manual please call King Controls at ( 800) 982-9920 or visit our website at www.kingcontrols.com. TABLE OF CONTENTS Section Contents Page 1. INTRODUCTION.....................................................................................2 2. DEFINITION OF TERMS ...........................................................
SECTION 1 INTRODUCTION The King-Dome AutoScan Satellite System includes 2 main components (Fig. 1). Dome (Antenna) Unit Located on the roof of the vehicle. The dish is covered by a protective dome that keeps operational components free from the elements. Controller Located in the vehicle. Used to activate the system, position the dish, and access diagnostic information. Note: A TV, satellite receiver, and program subscription are also required for satellite TV viewing. (Purchased separately.) Fig.
SECTION 2 DEFINITION OF TERMS AZIMUTH: Circular rotation around the vehicle. (like a clock face: front of vehicle is 12:00, rear is 6:00) (Fig. 2) Fig. 2 ELEVATION: Angle in degrees measured from the ground plane (Fig. 3). Fig. 3 SIGNAL STRENGTH: Intensity of electronic signal received from the satellite transmission.
SECTION 3 INSTALLATION TOOLS AND MATERIALS REQUIRED: - drill and drill bit set tape measure 7/16” open end wrench (coax connections) adhesive sealant (compatible with roof material) appropriate fasteners to install all components and wiring 5/32” allen wrench, channel lock or pliers (to remove shipping bolts) wire cutter (to remove shipping tie strap) KIT CONTENTS: 1. Unpack and identify all components (Fig. 4). Fig.
IMPORTANT! The tie strap and spacer, and the bolts and washers must be removed from the bottom of the dome unit prior to installation. DO NOT REMOVE THE DOME COVER TO REMOVE THESE SHIPPING RESTRAINTS. YOU MUST PLUG THE SHIPPING BOLT HOLES WITH THE SUPPLIED PLUGS (ATTACHED TO TIE STRAP SHIPPING RESTRAINT). 2. Remove and discard the tie strap and spacer (KEEP RUBBER PLUGS), and the (2) bolts and (2) washers that pass through the bottom of the base (Fig. 5). 3.
DOME LOCATION 4. Select an area on the roof for the dome unit and the location where the wiring will enter the vehicle through the roof to the satellite receiver, controller, and 12 volt power source inside, using the following criteria: a) The shortest distance between the dome unit and the satellite receiver is most desirable. b) The dome unit requires a 28 inch diameter mounting area. c) The dome unit must be mounted on the centerline of the vehicle.
Fig. 7 Example of truck installation using bracket. See bracket instructions for proper installation. IMPORTANT! The dome unit MUST be mounted to the air ride cab: NEVER to any structure mounted directly to the frame. DOME INSTALLATION IMPORTANT! Make sure shipping restraints are removed from bottom of dome unit (Fig. 5, Page 5). Cable connections must ALWAYS be positioned facing the rear of vehicle. 5. Place dome unit on installation location chosen using the criteria discussed in the previous section.
Note: The installer is responsible for determining the most appropriate fastener to secure the dome unit to the roof. Depending on the roof material, fasteners such as lag screws, well nuts, sheet metal screws, toggle bolts and T anchors may be used, and should always be used in combination with a roof compatible sealant. IMPORTANT! The installer is responsible for weather proofing all holes with sealant. 7. Mount the dome unit.
. Run wires from the back of the dome unit to the roof edge, then along edge to location where wiring will be fed into the vehicle. (If installing an optional second receiver, run auxiliary coax to location where it will enter the vehicle.) Secure wiring to roof every 12-18 inches (Fig. 10). 12. Drill 3/4” hole through the roof and into the cabinet where receiver is stored. Feed wiring down through hole.
INTERNAL WIRING IMPORTANT: The connection between the dome unit and the receiver must be a direct connection with no devices in between. Any other devices should be downstream from the receiver. 14. Inside vehicle, connect main coax from the dome unit directly to the “satellite in” port of the main receiver. Do not go through an “A-B” or any other switch, box, or booster. Connect auxiliary coax directly to optional second receiver. IMPORTANT: Power connection must be a non-shared circuit.
SECTION 4 OPERATION IMPORTANT! There must be a clear “line of sight” to the southern sky. Mountains, buildings, trees, telephone poles, etc. can all block the satellite signal from reaching the dish. 1. Turn TV and satellite receiver on. 2. Go to the signal meter screen on TV. Choose transponder number: Dish Network DIRECTV #11 #19 3. Enter local ZIP code on signal meter screen to determine satellite elevation.
Elevation Map for DIRECTV 101 Find your location on the map. Use the elevation lines to determine your approximate elevation.
Elevation Map for Dish/DIRECTV 110 Find your location on the map. Use the elevation lines to determine your approximate elevation.
Elevation Map for Dish/DIRECTV 119 Find your location on the map. Use the elevation lines to determine your approximate elevation.
While the dish rotates, the direction of the dish in relation to the vehicle’s position will be displayed on the controller as a clock number. (The windshield is always 12:00 o’clock: see Fig. 2, Page 3.) This information can be used to determine when the dish is close to pointing at the desired satellite. IMPORTANT! You must continuously monitor the TV for signal strength while the dish is rotating. DO NOT WATCH THE KING-DOME CONTROLLER.
SECTION 5 STORE/RECALL POSITIONS Note: For use with multi-satellite services (such as Dish 500). Store Satellite Position #1 1. Once locked onto a desired satellite, hold LEFT AND RIGHT arrows simultaneously until display flashes. 2. Hold LEFT arrow until 1P (Position 1) appears on display. Position #1 is stored in memory for this position. Store Satellite Position #2 3. Once locked onto the second desired satellite, hold LEFT AND RIGHT arrows simultaneously until display flashes. 4.
SECTION 6 DIAGNOSTICS Page 17
SECTION 7 MAINTENANCE The King-Dome Satellite System has been designed to be maintenance and trouble free. For optimum signal strength, keep the dome clean from dirt, bugs, and other debris. Periodic washing of the dome with mild soap and water is recommended. If you plan on storing your vehicle for long periods of time, it is recommended that the system be put through a search procedure on a quarterly basis to keep all moving parts in good working order.
SECTION 8 LIMITED WARRANTY Every King Controls Satellite System is thoroughly inspected and tested before leaving the factory. It is covered by a two year parts and one year labor limited warranty from the date of original purchase. This warranty does not cover installation and external wiring or refurbished units. Should any trouble develop during the warranty period, contact King Controls or one of its certified dealers.
Notes Page 20
AutoScan 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.
