Operator’s Manual RB-60 Broadcast Spreader X7507840000 © 7/2019 ECHO Inc.
SAFETY RB-60 SAFETY Safety Information Carefully read these instructions before use. Improper use or failure to follow instructions can result in product failure or injuries. For safe use of this product you must read and follow all instructions before using. Cancer and Reproductive Harm www.P65Warnings.ca.gov ◆ ◆ ◆ ◆ 2 Do not allow anyone to operate the broadcast spreader without proper instructions. Do not permit children to operate the broadcast spreader.
RB-60 DESCRIPTION DESCRIPTION Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. The safety decal is for example only. Your label may appear slightly different. 3 4 1 5 2 8 6 7 9 RB60 Setting comparison chart / Cuadro comparativo / Régler selon la charte de comparaison 5 5 5 5.5 5.5 5.
CONTENTS RB-60 CONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. 1 Broadcast Spreader Asembly 2 Carriage Bolts 2 Wing Nuts 1 Quick Start Guide ASSEMBLY Install Handle Brackets 1.
RB-60 2. OPERATION Secure handle brackets with wing nuts (C) and carriage bolts (D) on each side. Note: Attach each side loosely before tightening brackets securely. D C Assure control cable is routed behind handle brackets. OPERATION Application Instructions TIP HAZARD. Unit can tip on uneven ground. Always fill hopper on flat ground, and keep bystanders away. Otherwise personal injury could result. X7507840000 © 7/2019 ECHO Inc.
OPERATION 1. RB-60 Fill Hopper Release actuator handle (A) to close gate. Fill hopper. A Note: Fill hopper in an area that won’t be damaged by spilled product. 2. Set Gate Adjustment Push gate adjuster (B) down and move to best application setting (see chart below). Pull adjuster upward to lock in place. Note: Gate adjustment settings should only be used as a B general guideline for application. Refer to instructions on material you are spreading for most accurate application setting requirements. 3.
RB-60 MAINTENANCE Sample Spread Pattern Muestra del patrón de disribución Modèle d’épandageetyp SHUT OFF HERE Apague aquí Arrêt ici START Inicio Mise en marche SHUT OFF HERE Apague aquí Arrêt ici RESTART Reinicie Remise en marche RESTART Reinicie Remise en marche SHUT OFF HERE Apague aquí Arrêt ici RESTART Reinicie Remise en marche RESTART Reinicie Remise en marche SHUT OFF HERE Apague aquí Arrêt ici MAINTENANCE Clean Spreader Avoid spraying gear case directly, and do not use a pressure washer on sp
MAINTENANCE RB-60 Check Tire Pressure Tires should be inflated to 14-18 psi. Assure tire pressure does not exceed 30 psi. Replacing Control Cable 1. Remove Shield (A). 2. Turn gate (B) clockwise to relieve tension on cable. C A B C 3. Remove cable S hook (C) from gate. C 8 X7507840000 © 7/2019 ECHO Inc.
RB-60 4. Remove upper handle bracket from lower handle bracket. 5. Remove bolts (D) and separate handle halves. 6. Install new handle half with control cable assembly. 7. Re assemble spreader components. MAINTENANCE D Assure control cable is routed behind handle brackets. X7507840000 © 7/2019 ECHO Inc.
SPECIFICATIONS RB-60 SPECIFICATIONS MODEL Length RB-60 959 mm (37.75 in.) Width 584 mm (23 in.) Height 794 mm (31.25 in.) Weight 10.2 kg (22.4 lb.) Capacity Weight 27.2 kg (60lb.) Volume 36.8 L (1.3 ft3) Loading Height 584 mm (23 in.) Wheels and Tires Tire Diameter 254 mm (10in.) Tire Type Pneumatic Recommended Pressure 96.5 - 124kPa (14-18 psi) PRODUCT REGISTRATION Thank you for choosing ECHO Power Equipment Please go to http://www.echo-usa.
RB-60 X7507840000 © 7/2019 ECHO Inc.
N29000001001 - N29000999999 ECHO INCORPORATED 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.
