Operator’s Manual DSRM-2600/U Grass Trimmer / Brushcutter Read and understand all provided literature before use. Failure to do so could result in serious injury. Cancer and Reproductive Harm www.P65Warnings.ca.
TABLE OF CONTENTS DSRM-2600/U TABLE OF CONTENTS Introduction................................................................................................................. 3 Servicing Information.................................................................................................. 3 Parts and Serial Number.................................................................................... 3 Service ..............................................................................................
DSRM-2600/U INTRODUCTION INTRODUCTION Specifications, descriptions, and illustrative material in this literature are as accurate as possible. Specifications are subject to change without notice. Illustrations might include optional equipment and accessories, and might not include all standard equipment. Your equipment might appear slightly different than pictured equipment. Read and understand all provided literature.
SAFETY DSRM-2600/U Service Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site www.echo-usa.com. When presenting your unit for Warranty service/ repairs, proof of purchase is required.
DSRM-2600/U SAFETY The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided. The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided.
SAFETY Symbol DSRM-2600/U Description Symbol Description Wear Hand and Foot Protection Beware of Fire Safety/Alert Do Not Dispose in Household Trash Keep Bystanders and Helpers Away 15 m (50 ft.) DO NOT USE LINE HEADS - Blades Only DO NOT USE BLADES Line Heads Only Do not expose to rain / water IPX4 Protected Against Splashing Water Note: Not all symbols will appear on your unit.
DSRM-2600/U SAFETY The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. Work Area Safety • Keep work area clean and well lit. Cluttered or dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. • Keep children and bystanders away while operating a power tool.
SAFETY DSRM-2600/U • Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. • Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery, picking up or carrying the tool.
DSRM-2600/U SAFETY Power Tool Use and Care • Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. • Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
SAFETY DSRM-2600/U • Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. • Do not open or destroy the battery. Electrolytes contained within the battery are corrosive and may cause damage to eyes or skin if released. It may be toxic if swallowed.
DSRM-2600/U SAFETY Discard all toxic materials in a specified manner to prevent contamination of the environment. Before discarding a damaged or worn out Lithium-ion battery, contact your local waste disposal agency, or the local Environmental Protection Agency for information and specific instructions. Take the batteries to a local recycling and/or disposal center, certified for Lithium-ion disposal. If the battery cracks or breaks, with or without leaks, do not recharge it and do not use.
SAFETY DSRM-2600/U This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
DSRM-2600/U SAFETY Keep a Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach. • Keep cutting attachment below waist. • Keep all body parts away from rotating cutting attachment. Equipment Use only approved attachments. Serious injury may result from the use of a non-approved attachment combination.
SAFETY ◆ ◆ ◆ ◆ ◆ 14 DSRM-2600/U DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit. NEVER reach into any opening while the unit is running. Moving parts may not be visible through openings. Position wiring safely to prevent snagging, separation of connectors, or breakage during operation.
DSRM-2600/U DESCRIPTION DESCRIPTION Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. Safety label is for example only. Your label may appear slightly different. 1. Gear Case 2. Nylon Line Head 3. Debris Shield 4. Cut-off Knife 5. Drive Shaft Assembly 6. Support Handle - For Left Hand 7. U-Handle Assembly 8.
CONTENTS 9. Power Indicator LED 10. Power Button 11. - Button 12. + Button 13. Trigger Switch Lockout 14. Trigger Switch 15. Power Head 16. Battery Compartment 17. Throttle Handle - For Right Hand 18. Shoulder Harness DSRM-2600/U CONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage.
DSRM-2600/U ASSEMBLY ASSEMBLY DSRM-2600: Note: Label shows minimum spacing for support handle location. 1. If necessary, position support handle for comfortable operation and securely tighten screws. DSRM-2600U: Parts required: U-Handle assembly, handle bolt 1. Install U-handle clamp (A) to drive shaft clamp (B). Secure with U-handle bolt (C).
ASSEMBLY 2. 3. Loosen upper two (2) U-handle clamp screws (D) and position U-handle assembly for comfortable operation. DSRM-2600/U A B D Tighten U-handle clamp screws. C D D Shield Installation (Nylon line operation) Parts required: Shield with cutoff knife, Shield Plate, three screws, line head plate. Shield with cutoff knife is for use with the Nylon Line Head only. Install shield without cutoff knife when using plastic or metal blades, or serious injury may result. 1. 2. 3.
DSRM-2600/U ASSEMBLY Wear Gloves or personal injury may result: ◆ Cutoff knife is sharp. ◆ Gearcase and surrounding area may be hot. 1. Align notch in edge of shield and hole in line head plate with notch in edge of gear housing and insert head locking tool (G). 2. Thread line head (J) onto PTO shaft by turning it counterclockwise until head is tight against line head plate. 3. Remove locking tool (G). G J Semi-automatic nylon line heads must be used only with debris shield with cut-off knife.
ASSEMBLY DSRM-2600/U • Keep charger and battery away from damp conditions and all liquids. • Do not operate the charger on an easily combustible surface (e.g. paper, textiles) or in an environment with a high risk of fire. • Do not cover the charger. Covering the charger will prevent it from cooling. • Do not operate the charger in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
DSRM-2600/U ASSEMBLY The battery comes partially charged from the factory and needs to be fully charged before first use. Charge the battery when it no longer produces sufficient power to operate the unit or when battery lights indicate that the battery is low. 1. Plug charger AC cord in the wall outlet. 2. Align ridges on battery with grooves on charger, and slide battery into charger. 3. During normal charging, the charger LED (A) will blink GREEN.
ASSEMBLY DSRM-2600/U Installing the Battery The attachment will operate when the battery is installed, the power indicator LED is lit, and the trigger switch and trigger switch lockout are engaged. Make sure the unit is properly positioned to prevent loss of control and possible serious injury. Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown.
DSRM-2600/U OPERATION Removing the Battery To remove battery, depress battery latch release (C) slide battery out of power head. C Balance and Adjust Unit - U model 1. Loosen harness clamp screw. 2. Put on harness and attach unit to harness. 3. Slide harness clamp up (A) or down until unit balances with head approximately 50-75 mm (2-3 in.) from the ground. 4. Tighten harness clamp screw. 5. Loosen U-Handle clamp screws (B), and position U-Handle for comfortable operation. 6.
OPERATION DSRM-2600/U Blade use demands specific brushcutter configuration. Operation without specified shield, barrier bar or U-handle, and harness can result in serious personal injury. Follow installation instructions.
DSRM-2600/U OPERATION • A new cotter pin is required each time a blade is installed. • Shoulder harnesses may be used on all trimmers and brushcutters to reduce operator fatigue. Brushcutters over 7.5 kg (16.5 lbs.) dry weight (without fuel) and U-handle brushcutters require a double shoulder harness. Note: The barrier bar is used to restrict rearward movement of the unit. The barrier bar is not a handle and should not be gripped when using or carrying the unit.
OPERATION DSRM-2600/U Always use extreme care when carrying or handling the equipment to avoid contact with the cutting edges of the blade. Use the optional blade cover when unit is not in use. Keep blades in protective packaging until ready to install. Store blades safely after removal to prevent injury from accidental contact. Use blade protectors to protect blade teeth during unit transportation.
DSRM-2600/U OPERATION 1. Keep movable parts of the attachment away from objects that could become entangled or thrown, and surfaces that could cause loss of control. 2. Push power button (A) once to turn on power to unit. Power indicator LED (B) illuminates when power to unit is turned on. 3. Hold down trigger switch lockout (C) and depress trigger switch (D) to increase RPM to operating speed. Note: To increase operating speed, press + (E). To decrease operating speed, press - (F).
OPERATION 1. Release trigger switch and trigger switch lockout, and allow trimmer head to stop. 2. Push power button (A) to turn off power to unit. DSRM-2600/U • Power indicator LED (B) turns off when power to unit is turned off. • If the trimmer head does not stop when the trigger and trigger lockout are released, push power button to turn off and remove the battery to stop the power supply to product. Have your authorized servicing dealer repair power button before using product again.
DSRM-2600/U OPERATION Scything Scything - Swing the cutting head in a level arc, gradually feeding the line into the material being cut. Move forward with each arc to cut a swath. Width of cutting swath depends on arc. Use a larger arc for a wider swath, or a smaller arc for a narrow swath. Keep line head tilted to direct cutting debris forward or away from you. Edging and Scalping Both of these are done with the nylon line cutting head tilted at a steep angle.
OPERATION DSRM-2600/U • Width of cutting swath depends on arc. Use a larger arc for a wider swath, or a smaller arc for a narrow swath. Suggested cutting width is about 1.5 m (4.9 ft). • When scything large brush up to 12.7 mm (0.5 in.) diameter from right to left, avoid cutting with highlighted section. Reaction Forces ◆ ◆ ◆ ◆ ◆ The cutting attachment will continue to rotate even after the throttle is released, maintain control of the unit until it has come to a complete stop.
DSRM-2600/U OPERATION Push and Pull Forces Push and pull forces are reactive forces that push the equipment directly toward the operator, or that pull the equipment directly away from the operator. These forces are the result of cutting on the sides of the blade. The direction of the force depends on the side of the blade being used, and the direction of blade rotation at the point of contact.
OPERATION DSRM-2600/U Blade Cutting Problems Binding - Blades may bind in the cut if dull or forced. Binding can damage blade, and result in blade breakage or injury from fragments and flying debris. If a blade binds in a cut, don’t try to get it out by applying “up and down” force to pry the cut open. Applying prying force to the blade can bend the blade, and result in blade failure and injury.
DSRM-2600/U MAINTENANCE MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop unit and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces. Operating a poorly maintained unit can result in serious injuries to operator or bystanders.
MAINTENANCE DSRM-2600/U Maintenance Intervals COMPONENT OR SYSTEM MAINTENANCE PROCEDURE Skill Level Daily Or Before Use Battery / Battery Compartment Inspect / Clean / Charge Cut Off Knife Inspect / Clean 1 1 Screws / Nuts / Bolts Inspect / Tighten / Replace 1 Drive Shaft Grease 1 1 Gear Housing Grease 2 1 MAINTENANCE PROCEDURE NOTES: 1 Apply lithium based grease every 25 hours of use. 2 Apply lithium based grease every 50 hours of use.
DSRM-2600/U MAINTENANCE Cleaning battery and battery compartment Risk of electric shock or fire. Do not use conducting materials to clean battery or battery compartment. Otherwise serious personal injury may result. 1. Release trigger switch and trigger switch lockout and allow trimmer head to stop. 2. Make sure power indicator LED is not illuminated. 3. Depress battery latch release (A) and slide battery out of power head. 4.
MAINTENANCE DSRM-2600/U Lubrication Level 1. Parts Required: Lithium Based Grease. Gear Case Gear cases without grease plug (A) do not require lubrication. 1. Clean all loose debris from gear case. 2. Remove plug (A) and check level of grease. 3. Add grease if necessary. DO NOT over-fill. A Flex Cable 1. Loosen handle clamping screw (B) and slide throttle handle forward. B 2. Loosen clamping screw (C) and slide shaft out of power head.
3. Pull flex cable (D) out of shaft housing, wipe clean and recoat with 15 ml (0.5 oz.) grease. 4. Slide flex cable (D) back into shaft housing. DO NOT get dirt on flex cable. 5. Reassemble in reverse order. MAINTENANCE D DSRM-2600/U Nylon Line Replacement Wear gloves or personal injury may result: ◆ Cut-off knife is sharp. ◆ Gearcase and surrounding area may be hot. Never use wire or wire-rope that can break off and become a dangerous “projectile”. Serious injury can occur. 1.
MAINTENANCE 3. Insert one end of trimmer line into an eyelet, and push line equal distance through trimmer head. 4. Hold trimmer head while turning knob clockwise to wind line onto spool until about 13 cm (5 in.) of each line remains exposed. DSRM-2600/U Trimmer head is now fully loaded and ready for operation. When the wear indicators located at the bottom of the Speed-Feed® head are worn smooth, or if holes appear, replacement of the cover or the entire Speed-Feed® head required.
DSRM-2600/U MAINTENANCE Sharpening Metal Blades Metal blades are very sharp and can cause severe injuries, even if unit is off and blades are not moving. Avoid contact with blades. Wear gloves to protect hands. Several styles of metal blades are approved for use on the Brushcutter. The 8-tooth blade can be sharpened during normal maintenance. The clearing blade and 80-tooth blade require professional service.
TROUBLESHOOTING 3. After sharpening teeth, check each tooth radius for evidence of a square (sharp) corner. Use the round (rat tail) file to renew the radius.
DSRM-2600/U STORAGE Trouble Line won’t feed Line fails to cut off Cause Solution Not enough line on the spool Refill with new line Line tangled in the spool Untangle and refill line Cut off knife is damaged or missing Consult your dealer Checking and maintenance requires specialist knowledge. If you are unable to check and maintain the product or deal with a fault yourself, consult your dealer. Do not attempt to dismantle the product.
STORAGE 6. DSRM-2600/U Store unit in a dry, dust-free place out of the reach of children. Battery 1. Remove battery. 2. Store in a dry, dust-free place, out of the reach of children. 3. Store in temperatures between -20o C (-4 F) and 60o C (140 F). 4. If battery is stored for longer than six months, charge it to 100% capacity. Charger 1. Remove battery from charger. 2. Disconnect charger from power supply. 3. Store in a dry, dust-free place, out of the reach of children.
DSRM-2600/U SPECIFICATIONS SPECIFICATIONS MODEL Length DSRM-2600 DSRM-2600U 1841 mm (72.48 in.) Width 215 mm (8.46 in.) 669 mm (26.34 in.) Height 293 mm (11.54 in.) 618 mm (24.33 in.) 5.4 kg (11.9 lb.) 6.1 kg (13.45 lb) Weight (with battery) Battery ECHO eFORCE™ 56V series batteries Type Li-Ion Battery voltage 56 (rated 50.
WARRANTY DSRM-2600/U WARRANTY Limited Warranty Statement for ECHO 56 Volt Handheld Products and Walk Behind Mowers sold in USA and Canada ECHO Incorporated warrants to the original retail purchaser that this ECHO brand 56 Volt outdoor product is free from defects in material and workmanship and agrees to repair or replace, at ECHO Incorporated’s discretion, any defective product free of charge within these time periods from the date of purchase: If the product is for homeowner use: • Units and Bare Too
DSRM-2600/U PRODUCT REGISTRATION PRODUCT REGISTRATION Thank you for choosing ECHO Power Equipment Please go to http://www.echo-usa.com/Warranty/Register-Your-ECHO to register your new product on-line. It's FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Incorporated. Registering your purchase enables us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
DSRM-2600/U ECHO Incorporated PRODUCT REGISTRATION 46 X7508163901 © 3/22 ECHO Incorporated
DSRM-2600/U NOTES NOTES X7508163901 © 3/22 ECHO Incorporated 47
U56200001001 - U56200999999 U56500001001 - U56500999999 ECHO INCORPORATED 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.
