Operator’s Manual DPE-2100 Power Edger Read and understand all provided literature before use. Failure to do so could result in serious injury. Cancer and Reproductive Harm www.P65Warnings.ca.
TABLE OF CONTENTS DPE-2100 TABLE OF CONTENTS Introduction ................................................................................................. 3 Servicing Information .................................................................................. 4 Parts and Serial Number...................................................................... 4 Service ................................................................................................. 4 ECHO Consumer Product Support ...........
DPE-2100 INTRODUCTION INTRODUCTION Specifications, descriptions, and illustrative material in this literature are as accurate as possible. Specifications are subject to change without notice. Illustrations might include optional equipment and accessories, and might not include all standard equipment. Your equipment might appear slightly different than pictured equipment. Read and understand all provided literature.
SERVICING INFORMATION DPE-2100 SERVICING INFORMATION Parts and Serial Number Genuine ECHO parts and assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts, always have the model number and serial number of the unit with you. For future reference write them in the space provided below. Model No. _____________________ Serial No.
DPE-2100 SAFETY SAFETY For safe use of your product Be careful to read this section before using your product. • The precautions described in this section contain important safety information. Please observe them carefully. • You must also read the precautions that appear in the body of the manual itself. Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words.
SAFETY DPE-2100 International Symbols Symbol Description Symbol Description Warning, See Operator’s Manual Direct Current Wear Eye, Ear and Head Protection Do not expose to rain / water Wear Hand and Foot Protection Rotating Cutting Attachment Safety/Alert Beware of thrown objects Disconnect battery before maintenance Hot Surface Keep Bystanders and Helpers Away 15 m (50 ft.) Note: Not all symbols will appear on your unit.
DPE-2100 SAFETY Read Manuals • Provide all users of this equipment with literature for instructions on safe operation. Clear the Work Area • Always clear the work area of foreign objects such as rocks, broken glass, nails, wire, or string, which can be thrown or become entangled in the cutting attachment, and check for any hidden hazards. Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 50 ft. (15 m) while the unit is in use. • Outside the 50 ft.
SAFETY DPE-2100 Handling the Product General Safety Warnings and Instructions This section contains the prescribed general safety warnings and instructions for battery-powered products contained in UL 2595 and for handheld tools, transportable tools and lawn and garden machinery contained in UL 62841-1. Additional important warnings and instructions are provided in subsequent sections of this manual.
DPE-2100 SAFETY • Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. • When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
SAFETY DPE-2100 • Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second. Proper Clothing Wear snug-fitting, durable clothing: • Pants should have long legs, shirts should have long sleeves. • DO NOT WEAR SHORTS. • DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become entangled in moving parts or surrounding growth.
DPE-2100 SAFETY • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. • Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
SAFETY DPE-2100 Service • Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care. • Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. • Never service damaged battery packs. Service of battery packs should only be performed manufacturer or authorized service providers.
DPE-2100 SAFETY If the battery cracks or breaks, with or without leaks, do not recharge it and do not use. Discard it and replace with a new battery. DO NOT TRY TO REPAIR IT! To prevent injury and risk of fire, explosion, or electric shock, and to avoid damage to the environment: • Cover the terminals of the battery with heavy-duty adhesive tape. • DO NOT try to remove or destroy any of the battery components. • DO NOT try to open the battery.
SAFETY DPE-2100 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
DPE-2100 SAFETY Equipment Use only ECHO attachments. Serious injury may result from the use of a non-approved attachment combination. ECHO Incorporated will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety manual. ◆ Check unit for loose or missing nuts, bolts, and screws. Tighten or replace as needed.
SAFETY DPE-2100 General Safety Warnings and Instructions for the following ECHO tools: Curved Shaft Edger, Straight Shaft Edger, Tiller Cultivator, or Pole Pruner, or DPAS unit configured as a Curved Shaft Edger, Straight Shaft Edger, Tiller Cultivator, or Pole Pruner. This section contains the prescribed general safety warnings and instructions for handheld, motor-operated electric trimmers, lawn edgers, cultivators, and pole pruners contained in UL 82.
DPE-2100 9. SAFETY Don't Force Tool - It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed. 10. Don't Overreach - Keep proper footing and balance at all times. 11. Stay Alert - Watch what you are doing. Use common sense. Do not operate appliance when you are tired. 12. Store Idle Tools Indoors - When not in use, tools should be stored indoors in dry, locked place out of reach of children with the battery removed. 13.
SAFETY DPE-2100 • Do not use the extended-reach pruner in bad weather conditions, especially when there is a risk of lightning. This decreases the risk of being struck by lightning. • To reduce the risk of electrocution, never use near any electrical power lines. Contact with or use near power lines may cause serious injury or electric shock resulting in death. • Always use two hands when operating the extended-reach pruner. Hold the extended-reach pruner with both hands to avoid loss of control.
DPE-2100 DESCRIPTION DESCRIPTION Locate these safety decal(s) or etching(s) on your unit. Make sure they are legible, and that you understand and follow the instructions. If any cannot be read, replacements can be ordered from your ECHO dealer. Images shown below are for example only. Those on your unit might appear slightly different. 3 1 2 5 4 6 7 10 9 8 11 For use only with ECHO eFORCE 56V battery series. See operator’s manual for list of compatible model numbers.
DESCRIPTION DPE-2100 1. Power Head 2. Throttle Handle - For Right Hand 3. Speed Switch 4. Lock Off Lever Switch 5. Power Switch 6. Support Handle - For Left Hand 7. Driveshaft Assembly 8. Wheel 9. Blade 10. Debris Shield 11.
DPE-2100 CONTENTS CONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. 1 Power Head / Drive Shaft Assembly 1 Operator's Manual 2 Split Pins 1 Battery* 1 Battery Charger* *Not all units include battery and charger.
ASSEMBLY DPE-2100 Temperature Information Recommended Ambient Temperatures: Charging Low Product (1) High Not Applicable Battery 39°F (4°C) 104°F (40°C) Charger 39°F (4°C) 104°F (40°C) (2)(3) Usage/Discharge Storage Low High Low High 32°F (0°C) 113°F (45°C) 32°F (0°C) 113°F (45°C) 32°F (0°C) 113°F (45°C) 32°F (0°C) 113°F (45°C) 32°F (0°C) 113°F (45°C) Not Applicable (1) Assumes the battery is just off the charger or stored at the temperature range noted for charger usage (39° F
DPE-2100 ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ASSEMBLY Do not operate the charger in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Charger can produce sparks which may ignite the dust or fumes - there is a risk of explosion. Connect the charger only to the mains of voltage and frequency specified on the rating plate. Connect the charger only to an easily accessible wall outlet. Never insert objects in the battery's or charger's cooling slots.
ASSEMBLY DPE-2100 Note: Your charger might look different from those pictured. 1. Plug charger AC cord in the wall outlet. 2. Align ridges on battery with grooves on charger, and slide battery into charger. 3. During normal charging, the charger LED (A) will blink GREEN. A A A If charger detects a problem, LED will blink RED. Remove battery from charger, clear obstructions from contacts and reinstall battery into charger.
DPE-2100 ASSEMBLY • Two green lights indicate that the battery has 25-54% charge. • Three green lights indicate that the battery has 55-79% charge. • Four green lights indicate that the battery has 80-100% charge. 6. Unplug charger AC cord from the wall outlet. Battery Installation The attachment will operate when the battery is installed, and the lock off lever switch (if applicable), and power switch are engaged.
ASSEMBLY DPE-2100 Battery Removal To remove battery, depress battery latch release (C) slide battery out of power head.
DPE-2100 OPERATION OPERATION Starting Unit The attachment will operate when the battery is installed, and the lock off lever switch (if applicable), and power switch are engaged. Make sure the product is properly positioned to prevent loss of control and possible serious injury. Note: This model has two operating modes: low and high. Use speed switch to move between low mode (turtle) and high mode (rabbit). Use power switch to increase RPM speed within each mode. 1.
OPERATION DPE-2100 Stopping Unit The cutting attachment continues to run for a short period after the unit is switched off. 1. 2. Release power switch (C) and allow cutting attachment to stop. If unit does not stop when power switch is released, remove the battery to stop the power supply to product. Have your authorized servicing dealer repair unit before using product again. A B C Edger Operation Techniques 1. Before edging, water the area to soften the ground to make edging easier. 2.
DPE-2100 4. OPERATION Loosen adjustment knob (A). Move wheel up to increase cutting depth, or down to decrease cutting depth. A depth of 0.5 in. (13 mm) is optimal. Tighten adjustment knob (A). A A 5. 6. Before edging, plan your direction of travel so that the unit will always be positioned on your right side and so that you walk on a hard surface whenever possible. 13 mm (0.5 in.) Position edger as shown.
MAINTENANCE DPE-2100 The complete unit, specifically the drive shaft assembly may become very hot during use. Avoid contact during and immediately after operation, otherwise serious personal injury may result. MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop unit and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
DPE-2100 MAINTENANCE Maintenance Intervals COMPONENT OR SYSTEM MAINTENANCE PROCEDURE Skill Level Daily Or Before Use Battery / Battery Compartment Inspect / Clean / Charge 1 Screws / Nuts / Bolts Inspect / Tighten / Replace 1 Drive Shaft Gear Housing (Some Models) Grease 1 2 Grease 2 2 MAINTENANCE PROCEDURE NOTES: 1 Apply lithium based grease every 25 hours of use. 2 Apply lithium based grease every 50 hours of use.
MAINTENANCE DPE-2100 Maintenance and Care Remove battery before performing maintenance procedures. Cleaning battery and battery compartment Risk of electric shock or fire. Do not use conducting materials to clean battery or battery compartment. Otherwise serious personal injury may result. 1. Release power switch and allow unit to stop. 2. Depress battery latch release (A) and slide battery out of power head. 3.
DPE-2100 MAINTENANCE Lubrication Level 1. Parts Required: Lithium-based Grease. Gear cases without grease plug (A) do not require lubrication. Note: Your debris shield may appear different than the debris shield shown. Gear Housing 1. Remove plug (A) and add grease to gear housing. Do not overfill. 2. Replace plug and tighten securely. A Drive Shaft C 1. Loosen clamping screw (B) and remove locating screw (C). Pull gear box and shield from drive shaft housing. 2.
MAINTENANCE DPE-2100 Edger Blade Replacement Level 1. Parts required: Blade, new split pin. Note: Replace blade when it is bent, damaged, or worn shorter than 152.4 mm (6 in.). Wear gloves or personal injury may result Gearcase and surrounding area may be hot. 1. Remove split pin (A). G B 2. Align hole in inner blade adapter (B) with notch in gear housing, and insert locking tool (G) to prevent PTO shaft (C) from rotating. 3. Remove L.H. blade nut (D) by turning clockwise.
DPE-2100 TROUBLESHOOTING TROUBLESHOOTING Trouble Cause Solution Red Charger LED flashes or does not light up Plug not connected to power outlet Plug in the charger Battery not installed properly Check the battery installation Obstructed connection Reinstall battery again after remove obstructions from connection Fault in the charger Consult your dealer Fault in the battery Consult your dealer Unit will not turn on Battery not installed properly Check the battery installation Unit does no
STORAGE DPE-2100 STORAGE Storage Do not store in an enclosure where combustible fumes may accumulate. Fire may result. When storing the product for long periods of time, ensure that the following preparations for storage are carried out. Unit Do not store your unit without performing protective storage maintenance which includes the following: 1. Turn power to unit off. 2. Remove battery. 3. Remove accumulation of dirt and debris from exterior of unit. 4. Tighten all screws and nuts. 5.
DPE-2100 STORAGE Disposal Major plastic parts making up the product have codes showing their materials. The codes refer to the following materials; dispose of those plastic parts in accordance with local regulations. Materials Mark Material >PA6-GF< Nylon 6 - Glass fiber >PP-GF< Polypropylene - Glass fiber >PE-HD< Polyethylene >PP< Polypropylene • Battery contains lithium. Dispose of only at a designated collection point. • Lithium-ion batteries must be disposed of properly.
SPECIFICATIONS DPE-2100 SPECIFICATIONS MODEL DPE-2100 Length 1,751mm (69 in.) Width 302 mm (12 in.) Height 345 mm (13 in.) Weight (without cutter and battery) 4.2 kg. (9 lbs.) ECHO eFORCE® 56V series batteries Battery Type Li-Ion Battery voltage 56 (rated 50.4) Capacity See Battery Manual ECHO eFORCE® 56V series charger Charger type Charger input voltage 120V AC 60Hz Charging time See Battery Manual Operating Rod 25.0 mm (0.98 in.) aluminum tube Drive Shaft 6.35 mm (0.25 in.
DPE-2100 WARRANTY WARRANTY ––– WARRANTY Limited Warranty Statement for ECHO 56 Volt Handheld Products and Walk Behind Mowers sold in USA and Canada ECHO Incorporated warrants to the original retail purchaser that this ECHO brand 56 Volt outdoor product is free from defects in material and workmanship and agrees to repair or replace, at ECHO Incorporated’s discretion, any defective product free of charge within these time periods from the date of purchase: If the product is for homeowner use: • Units a
PRODUCT REGISTRATION DPE-2100 PRODUCT REGISTRATION Thank you for choosing ECHO Power Equipment Please go to http://www.echo-usa.com/Warranty/Register-Your-ECHO to register your new product on-line. It's FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Incorporated. Registering your purchase enables us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
PRODUCT REGISTRATION ECHO Incorporated DPE-2100 X7508310301 © 12/23 ECHO Incorporated 41
NOTES DPE-2100 NOTES 42 X7508310301 © 12/23 ECHO Incorporated
DPE-2100 X7508310301 © 12/23 ECHO Incorporated NOTES 43
U76000001001 - U76000999999 ECHO INCORPORATED 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.
