Operator’s Manual DPAS-2600SB Pro Attachment Series™ Read and understand all provided literature before use. Failure to do so could result in serious injury. Cancer and Reproductive Harm www.P65Warnings.ca.
TABLE OF CONTENTS DPAS-2600SB TABLE OF CONTENTS Introduction ................................................................................................. 3 Servicing Information .................................................................................. 4 Parts and Serial Number...................................................................... 4 Service ................................................................................................. 4 ECHO Consumer Product Support ........
DPAS-2600SB INTRODUCTION INTRODUCTION Specifications, descriptions, and illustrative material in this literature are as accurate as possible. Specifications are subject to change without notice. Illustrations might include optional equipment and accessories, and might not include all standard equipment. Your equipment might appear slightly different than pictured equipment. Read and understand all provided literature.
SERVICING INFORMATION DPAS-2600SB SERVICING INFORMATION Parts and Serial Number Genuine ECHO parts and assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the model number and serial number of the unit with you. For future reference write them in the space provided below. Model No. _____________________ Serial No.
DPAS-2600SB SAFETY SAFETY Manual Safety Symbols and Important Information Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you. The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided.
SAFETY DPAS-2600SB International Symbols Symbol Description Symbol Description Warning, See Operator’s Manual Beware of Fire Wear Eye, Ear and Head Protection Do Not Dispose in Household Trash Wear Hand and Foot Protection Guaranteed Sound Power Level Safety / Alert DO NOT USE Line Head - Blades Only Hot Surface DO NOT USE BLADES Line Head Only AVOID KICKOUT Keep Bystanders At Least 15 m (50 ft.) Away Beware Thrown Objects Wear Eye Protection Keep Bystanders and Helpers Away 15 m (50 ft.
DPAS-2600SB SAFETY Symbol Description Symbol Description Thrown Objects Wear Face Shield Finger Severing Wear Slip Resistant Footwear Do not operate closer than 15 m (50 ft.) from electrical hazards. Keep bystanders at least 15 m (50 ft.) away. Plan a retreat path from falling objects. Do not expose to rain / water Note: Not all symbols will appear on your unit.
SAFETY DPAS-2600SB • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. Electrical Safety • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
DPAS-2600SB SAFETY • Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. • Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts.
SAFETY DPAS-2600SB • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. • Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use.
DPAS-2600SB SAFETY • Do not expose a battery or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C (266°F) may cause explosion. • Follow all charging instructions and do not charge the battery or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
SAFETY DPAS-2600SB If the battery cracks or breaks, with or without leaks, do not recharge it and do not use. Discard it and replace with a new battery. DO NOT TRY TO REPAIR IT! To prevent injury and risk of fire, explosion, or electric shock, and to avoid damage to the environment: • Cover the terminals of the battery with heavy-duty adhesive tape. • DO NOT try to remove or destroy any of the battery components. • DO NOT try to open the battery.
DPAS-2600SB SAFETY Read the Manuals • Provide all users of this equipment with the operator’s manual for instructions on safe operation. Clear the Work Area • Always clear the work area of foreign objects such as rocks, broken glass, nails, wire, or string, which can be thrown or become entangled in the cutting attachment, and check for any hidden hazards. Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 50 ft. (15 m) while the unit is in use.
SAFETY ◆ ◆ ◆ ◆ ◆ DPAS-2600SB Inspect shield for damage and ensure that shield is properly installed, and that the cutoff knife is securely in place. Replace if either is damaged or missing. Check that the cutting attachment is firmly attached and in safe operating condition. Manufacturer recommended flexible non-metallic line is installed in the trimmer head. Assure that trigger switch, trigger switch lockout, and stop switch all work properly.
DPAS-2600SB DESCRIPTION DESCRIPTION Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. Safety label is for example only. Your label my appear slightly different. 1. Drive Shaft Coupler 2. Upper Drive Shaft Assembly 3. Support Handle - For Left Hand 4. Power Button 5. Trigger Switch Lockout 6. Throttle Handle - For Right Hand 7.
DESCRIPTION 10. Lower Drive Shaft Assembly 11. Debris Shield With Cutoff Knife 12. Cutoff Knife 13. Power Indicator LED 14. - Button 15. + Button 16.
DPAS-2600SB ASSEMBLY ASSEMBLY Support Handle Installation Note: Label shows minimum spacing for support handle location. 1. If necessary, position support handle for comfortable operation and securely tighten screws. Power Head Shaft to Lower Shaft Assembly 1. Set Power Head/Shaft Assembly on a level surface. 2. Pull locater pin (A) out, and turn counterclockwise one-quarter turn to lock-out position. 3. Remove storage hook and cap from attachment drive shaft.
ASSEMBLY DPAS-2600SB Battery Charging Note: See separate operator’s manuals packaged with battery and charger. • Use only with ECHO eFORCE™ 56V battery series batteries and chargers. • Keep charger and battery away from damp conditions and all liquids. • Do not operate the charger on an easily combustible surface (e.g. paper, textiles) or in an environment with a high risk of fire. • Do not cover the charger. Covering the charger will prevent it from cooling.
DPAS-2600SB ASSEMBLY • In the event of smoke or fire in the charger, disconnect it from the wall outlet immediately. • If the connecting cord is damaged, immediately disconnect the plug from the power supply to avoid the risk of electric shock. • Do not expose battery to microwaves or high pressure. • To reduce the risk of stumbling, position and mark the connecting cord in such a way that it cannot be damaged or endanger others.
ASSEMBLY 4. When charging is complete, LED will remain GREEN. See battery manual for charging time. 5. Verify battery is fully charged. Remove battery from charger, press battery charge status button (B), and check LED display. DPAS-2600SB B • One green light indicates that the battery has 0-25% charge. • Two green lights indicate that the battery has 25-50% charge. • Three green lights indicate that the battery has 50-75% charge. • Four green lights indicate that the battery has 75-100% charge. 6.
DPAS-2600SB 1. Make sure power to unit is turned off. 2. Align ridges (A) on battery with grooves in power head. Slide battery into power head. 3. Assure the battery latch (B) snaps into place and battery is secure before beginning operation. ASSEMBLY A B Assure battery latch is fully engaged before using unit. Removing the Battery To remove battery, depress battery latch release (C) slide battery out of power head.
ASSEMBLY DPAS-2600SB Balance and Adjust Unit 1. Loosen harness ring clamp screw (A). 2. Put on harness and attach unit to harness. 3. Slide harness clamp up or down until unit balances with head or blade 200 mm ± 100 mm (8 in ± 4 in) from the ground. 4. Tighten harness clamp screw. 5. Loosen handle clamp screw(s), and position handle for comfortable operation. 6. Tighten handle clamp screws securely.
DPAS-2600SB OPERATION OPERATION Operation with Blades Metal blades are very sharp and can cause severe injuries, even if unit is off and blades are not moving. Avoid contact with blades. Wear gloves to protect hands. Blade use demands specific brushcutter configuration. Operation without specified shield, barrier bar or U-handle, and harness can result in serious personal injury. Follow installation instructions.
OPERATION DPAS-2600SB • Arbor diameter of upper blade plate must match arbor diameter of blades. • For barrier bar or U-handle, follow instructions supplied with either blade conversion kit or U-handle kit, and verify blade is secured properly. • A new cotter pin is required each time a blade is installed. • Shoulder harnesses may be used on all trimmers and brushcutters to reduce operator fatigue. Brushcutters over 7.5 kg (16.5 lbs.
DPAS-2600SB OPERATION Always use extreme care when carrying or handling the equipment to avoid contact with the cutting edges of the blade. Use the optional blade cover when unit is not in use. Keep blades in protective packaging until ready to install. Store blades safely after removal to prevent injury from accidental contact. Use blade protectors to protect blade teeth during unit transportation.
OPERATION DPAS-2600SB Starting The Unit The attachment will operate when the battery is installed, the power indicator LED is lit, and the trigger switch and trigger switch lockout are engaged. Make sure the product is properly positioned to prevent loss of control and possible serious injury. 1. Keep movable parts of the attachment away from objects that could become entangled or thrown, and surfaces that could cause loss of control. 2. Push power button (A) once to turn on power to unit.
DPAS-2600SB OPERATION Stopping Unit The attachment continues to run for a short period after the unit is switched off. 1. Release trigger switch and trigger switch lockout, and allow attachment to stop. 2. Push power button (A) to turn off power to unit. • Power indicator LED (B) turns off when power to unit is turned off. • If the attachment does not stop when the trigger and trigger lockout are released, push power button to turn off and remove the battery to stop the power supply to product.
OPERATION DPAS-2600SB Scything Scything - Swing the cutting head in a level arc, gradually feeding the line into the material being cut. Move forward with each arc to cut a swath. Width of cutting swath depends on arc. Use a larger arc for a wider swath, or a smaller arc for a narrow swath. Keep line head tilted to direct cutting debris forward or away from you. Edging and Scalping Both of these are done with the nylon line cutting head tilted at a steep angle.
DPAS-2600SB OPERATION • Width of cutting swath depends on arc. Use a larger arc for a wider swath, or a smaller arc for a narrow swath. Suggested cutting width is about 1.5 m (4.9 ft). • When scything large brush up to 0.5" diameter from right to left, avoid cutting with highlighted section. Reaction Forces ◆ ◆ ◆ ◆ ◆ The cutting attachment will continue to rotate even after the throttle is released, maintain control of the unit until it has come to a complete stop.
OPERATION DPAS-2600SB Push and Pull Forces Push and pull forces are reactive forces that push the equipment directly toward the operator, or that pull the equipment directly away from the operator. These forces are the result of cutting on the sides of the blade. The direction of the force depends on the side of the blade being used, and the direction of blade rotation at the point of contact.
DPAS-2600SB OPERATION Blade Cutting Problems Binding - Blades may bind in the cut if dull or forced. Binding can damage blade, and result in blade breakage or injury from fragments and flying debris. If a blade binds in a cut, don’t try to get it out by applying “up and down” force to pry the cut open. Applying prying force to the blade can bend the blade, and result in blade failure and injury.
MAINTENANCE DPAS-2600SB MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop unit and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces. Operating a poorly maintained unit can result in serious injuries to operator or bystanders.
DPAS-2600SB MAINTENANCE Maintenance Intervals COMPONENT OR SYSTEM MAINTENANCE PROCEDURE Skill Level Daily Or Before Use Battery / Battery Compartment Inspect / Clean / Charge Cut Off Knife Inspect / Clean 1 Screws / Nuts / Bolts Inspect / Tighten / Replace 1 Drive Shaft Gear Housing 1 Grease 1 1 2 1 Grease MAINTENANCE PROCEDURE NOTES: 1 Apply lithium based grease every 25 hours of use. 2 Apply lithium based grease every 50 hours of use.
MAINTENANCE DPAS-2600SB Maintenance and Care Remove battery before performing maintenance procedures. Cleaning battery and battery compartment Risk of electric shock or fire. Do not use conducting materials to clean battery or battery compartment. Otherwise serious personal injury may result. 1. Release trigger switch and trigger switch lockout and allow trimmer head to stop. 2. Make sure power indicator LED is not illuminated. 3.
DPAS-2600SB MAINTENANCE Lubrication Level 1. Parts Required: Lithium Based Grease. Gear Case Gear cases without grease plug (A) do not require lubrication. 1. Clean all loose debris from gear case. 2. Remove plug (A) and check level of grease. 3. Add grease if necessary. DO NOT over-fill. A Drive Shaft (Lower) 1. 2. Loosen screw (B) and remove locating screw (C). Pull gear case and shield from drive shaft housing.
MAINTENANCE DPAS-2600SB Drive Shaft (Upper) 1. Loosen handle clamping screw (B) and slide throttle handle forward. B 2. Loosen clamping screw (C) and slide shaft out of power head. C 3. Pull flex cable (D) out of shaft housing, wipe clean and recoat with 15 ml (0.5 oz.) grease. 4. Slide flex cable (D) back into shaft housing. DO NOT get dirt on flex cable. 5. Reassemble in reverse order. D Nylon Line Replacement Wear gloves or personal injury may result: ◆ Cutoff knife is sharp.
DPAS-2600SB 1. Cut one piece of line to recommended length. 2.0 mm (0.080 in.) diameter 6 m (20 ft.). 2.4 mm (0.095 in.) diameter 6 m (20 ft.). 2. Align arrows on top of knob with openings in eyelets. 3. Insert one end of trimmer line into an eyelet, and push line equal distance through trimmer head. 4. Hold trimmer head while turning knob clockwise to wind line onto spool until about 13 cm (5 in.) of each line remains exposed. MAINTENANCE Trimmer head is now fully loaded and ready for operation.
MAINTENANCE DPAS-2600SB When the wear indicators located at the bottom of the Speed-Feed® head are worn smooth, or if holes appear, replacement of the cover or the entire Speed-Feed® head required. Sharpening Metal Blades Metal blades are very sharp and can cause severe injuries, even if unit is off and blades are not moving. Avoid contact with blades. Wear gloves to protect hands. Several styles of metal blades are approved for use on the Brushcutter.
DPAS-2600SB 1. 2. MAINTENANCE File each tooth at a 30° angle a specific number of times, e.g., four strokes per tooth. Work your way around the blade until all teeth are sharp. DO NOT file the ‘gullet’ (radius) of the tooth with the flat file. The radius must remain. A sharp corner will lead to a crack and blade failure. 30º 30º If an electric grinder is used, use care not to overheat teeth, do not allow tips/tooth to glow red or turn blue. DO NOT place blade in cooling water.
TROUBLESHOOTING DPAS-2600SB TROUBLESHOOTING TROUBLESHOOTING CHART Problem Red Charger light flashes or does not light up Unit will not turn on Unit does not run when turned on Running time is too short 40 Cause Remedy Plug not connected to power outlet. Plug in charger. Battery pack not installed properly. Check the battery installation. Obstructed connection. Reinstall battery after removing obstructions. Fault in the charger. Consult your dealer. Fault in the battery pack.
DPAS-2600SB STORAGE STORAGE Storage Do not store in an enclosure where combustible fumes may accumulate. Fire may result. When storing the product for long periods of time, ensure that the following preparations for storage are carried out. Unit Do not store your unit without performing protective storage maintenance which includes the following: 1. Turn power to unit off. 2. Remove battery. 3. Remove accumulation of dirt and debris from exterior of unit. 4. Tighten all screws and nuts. 5.
STORAGE DPAS-2600SB Disposal Major plastic parts making up the product have codes showing their materials. The codes refer to the following materials; dispose of those plastic parts in accordance with local regulations. Materials Mark Material >PA6-GF< Nylon 6 - Glass fiber >PP-GF< Polypropylene - Glass fiber >PE-HD< Polyethylene >PP< Polypropylene • Battery contains lithium. Dispose of only at a designated collection point. • Lithium-ion batteries must be disposed of properly.
DPAS-2600SB SPECIFICATIONS SPECIFICATIONS MODEL DPAS-2600 Length (with trimmer attachment) 1851 mm (72.87in.) Width (with trimmer attachment) 215 mm (8.46 in.) Height (with trimmer attachment) 297 mm (11.69 in.) Weight (with battery, with trimmer attachment) 5.2 kg (11.46 lb) Battery ECHO eFORCE™ 56V series batteries Type Li-Ion Battery voltage 56 V (rated 50.
SPECIFICATIONS DPAS-2600SB ECHO Optional Attachments Use only ECHO attachments. Serious injury may result from the use of non-ECHO attachment combinations. Read and comply with all safety instructions listed in this manual and attachment manual. ECHO Incorporated will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO for use with these units.
DPAS-2600SB WARRANTY WARRANTY Limited Warranty Handhel in USA ECHO Inc that this E fects in m place, at uct free of purchase: If the • • If the • • If the ies, and Cutting chains nylon ducing material nal produc rental or other This warrant commenc Any part ECHO Inc will be repai by an aut sories repl balance of The produc an author pense of ranty work after repai Incorporat making t breach of of the cont uct.
PRODUCT REGISTRATION DPAS-2600SB PRODUCT REGISTRATION Thank you for choosing ECHO Power Equipment Please go to http://www.echo-usa.com/Warranty/Register-Your-ECHO to register your new product on-line. It's FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Incorporated. Registering your purchase enables us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
PRODUCT REGISTRATION ECHO Incorporated DPAS-2600SB X7508230800 ©11/21 ECHO Incorporated 47
U56300001001 - U56300999999 ECHO INCORPORATED 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.
