Operator’s Manual DPAS-2600 Pro Attachment Series™ Read and understand all provided literature before use. Failure to do so could result in serious injury. Cancer and Reproductive Harm www.P65Warnings.ca.
TABLE OF CONTENTS DPAS-2600 TABLE OF CONTENTS Introduction................................................................................................................................................ 3 Servicing Information................................................................................................................................. 4 Parts and Serial Number ................................................................................................................. 4 Service.....
DPAS-2600 INTRODUCTION INTRODUCTION Specifications, descriptions, and illustrative material in this literature are as accurate as possible. Specifications are subject to change without notice. Illustrations might include optional equipment and accessories, and might not include all standard equipment. Your equipment might appear slightly different than pictured equipment. Read and understand all provided literature.
SERVICING INFORMATION DPAS-2600 SERVICING INFORMATION Parts and Serial Number Genuine ECHO parts and assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts, always have the model number and serial number of the unit with you. For future reference write them in the space provided below. Model No. _____________________ Serial No.
DPAS-2600 SAFETY SAFETY Manual Safety Symbols and Important Information Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you. The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided.
SAFETY DPAS-2600 International Symbols Symbol Description Symbol Description Warning, See Operator’s Manual Beware of Fire Wear Eye, Ear and Head Protection Do Not Dispose in Household Trash Wear Hand and Foot Protection Guaranteed Sound Power Level Safety / Alert DO NOT USE Line Head - Blades Only Hot Surface DO NOT USE BLADES Line Head Only AVOID KICKOUT Keep Bystanders At Least 15 m (50 ft.) Away Beware Thrown Objects Wear Eye Protection Keep Bystanders and Helpers Away 15 m (50 ft.
DPAS-2600 SAFETY Symbol Description Symbol Description Thrown Objects Wear Face Shield Finger Severing Wear Slip Resistant Footwear Do not operate closer than 15 m (50 ft.) from electrical hazards. Keep bystanders at least 15 m (50 ft.) away. Plan a retreat path from falling objects. Do not expose to rain / water Avoid blade kickout. Note: Not all symbols will appear on your unit.
SAFETY DPAS-2600 • When a bladed unit is used, there is the added risk of injury to bystanders being struck with the moving blade in the event of a blade thrust or other unexpected reaction of the blade. Keep a Firm Grip • Always hold throttle handle and support handle with thumbs and fingers tightly encircling the handles. Keep a Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not overreach.
DPAS-2600 SAFETY • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. Electrical Safety • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock. • Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators.
SAFETY DPAS-2600 • Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. • Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
DPAS-2600 SAFETY • Disconnect the plug from the power source and/or the battery from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
SAFETY DPAS-2600 • Exercise care in handling batteries to avoid shorting the battery with conducting materials such as rings, bracelets, keys, etc. The battery or conductor may overheat and cause burns if contact with said materials is made. • Do not use a battery or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury. • Do not expose a battery or tool to fire or excessive temperature.
DPAS-2600 SAFETY Discard all toxic materials in a specified manner to prevent contamination of the environment. Before discarding a damaged or worn out Lithium-ion battery, contact your local waste disposal agency, or the local Environmental Protection Agency for information and specific instructions. Take the batteries to a local recycling and/or disposal center, certified for Lithium-ion disposal. If the battery cracks or breaks, with or without leaks, do not recharge it and do not use.
SAFETY DPAS-2600 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
DPAS-2600 ◆ ◆ ◆ ◆ ◆ SAFETY Inspect shield for damage and ensure that shield is properly installed, and that the cutoff knife is securely in place. Replace if either is damaged or missing. Check that the cutting attachment is firmly attached and in safe operating condition. Manufacturer recommended flexible non-metallic line is installed in the trimmer head. Assure that power switch, lock off lever switch, operator presence switch, and enable button all work properly.
SAFETY DPAS-2600 General Safety Warnings and Instructions for the following ECHO tools: Curved Shaft Edger, Straight Shaft Edger, Tiller Cultivator, or Pole Pruner, or DPAS unit configured as a Curved Shaft Edger, Straight Shaft Edger, Tiller Cultivator, or Pole Pruner. This section contains the prescribed general safety warnings and instructions for handheld, motor-operated electric trimmers, lawn edgers, cultivators, and pole pruners contained in UL 82.
DPAS-2600 SAFETY 10. Don't Overreach - Keep proper footing and balance at all times. 11. Stay Alert - Watch what you are doing. Use common sense. Do not operate appliance when you are tired. 12. Store Idle Tools Indoors - When not in use, tools should be stored indoors in dry, locked place out of reach of children with the battery removed. 13. Maintain Tool with Care - Keep cutting edge sharp and clean for best performance and to reduce the risk of injury.
SAFETY DPAS-2600 • To reduce the risk of electrocution, never use near any electrical power lines. Contact with or use near power lines may cause serious injury or electric shock resulting in death. • Always use two hands when operating the extended-reach pruner. Hold the extended-reach pruner with both hands to avoid loss of control. • Always use head protection when operating the extended-reach pruner overhead. Falling debris can result in serious personal injury.
DPAS-2600 SAFETY General Safety Warnings and Instructions for the following ECHO tools: Hedge Trimmer, Mid-Reach Hedge Trimmer, Shafted Hedge Trimmer, or Articulating Hedge Trimmer, or DPAS unit configured as a Hedge Trimmer, Mid-Reach Hedge Trimmer, Shafted Hedge Trimmer, or Articulating Hedge Trimmer. This section contains the prescribed general safety warnings and instructions for handheld, motor-operated electric hedge trimmers contained in UL 62841-4-2.
SAFETY DPAS-2600 6. Keep all power cords and cables away from cutting area. Power cords or cables may be hidden in hedges or bushes and can be accidentally cut by the blade. 7. Do not use the hedge trimmer in bad weather conditions, especially when there is a risk of lightning. This decreases the risk of being struck by lightning. Extended-Reach Hedge Trimmer Safety Warnings: 1. To reduce the risk of electrocution, never use the extended-reach hedge trimmer near any electrical power lines.
DPAS-2600 SAFETY 3. Thoroughly inspect the area where the machine is to be used and remove all stones, sticks, wires, bones, and other foreign objects. Thrown objects can cause personal injury. 4. Before using the machine, always visually inspect to see that the cutter or blade and the cutter or blade assembly are not damaged. Damaged parts increase the risk of injury. 5. Before use, check the supply cord and any extension cord for signs of damage or aging.
SAFETY DPAS-2600 16. Do not operate the machine on excessively steep slopes. This reduces the risk of loss of control, slipping and falling which may result in personal injury. 17. When working on slopes, always be sure of your footing, always work across the face of slopes, never up or down and exercise extreme caution when changing direction. This reduces the risk of loss of control, slipping and falling which may result in personal injury. 18. Keep the supply cord away from the cutter, line or blade.
DPAS-2600 SAFETY Blade Thrust Safety Warnings: 1. Blade thrust is a sudden sideways, forward or backward motion of the machine, which may occur when the blade jams or catches on an object such as a sapling or a tree stump. It can be violent enough to cause the machine and/or operator to be propelled in any direction, and possibly lose control of the machine. 2. Maintain a firm grip with both hands on the machine and position your arms to resist blade thrust.
SAFETY ◆ ◆ DPAS-2600 Always hold throttle handle with right hand and support handle with left hand, placing unit on right side of body. Assure all ventilation openings are clear of debris. Note: To advance trimmer line, tap trimmer head against the ground while the head is turning at normal operating speed. Operation With Blades: Metal blades are very sharp and can cause severe injuries, even if unit is off and blades are not moving. Avoid contact with blades. Wear gloves to protect hands.
DPAS-2600 SAFETY Do Not install blades on GT (Curved Shaft) model trimmers. • Use only ECHO approved parts. Failure to use the correct parts can cause the blade to fly off. Serious injury to the operator and/or bystanders can occur. • Arbor diameter of upper blade plate must match arbor diameter of blades. • For barrier bar or U-handle, follow instructions supplied with either blade conversion kit or U-handle kit, and verify blade is secured properly.
SAFETY DPAS-2600 8-Tooth Weed/Grass Blade is designed for grass, garden debris and thick weeds up to 19 mm (0.75 in.) diameter. DO NOT use this blade for brush or heavy woody growth. 80-Tooth Brush Blade is designed for cutting brush and woody growth up to 13 mm (0.5 in.) diameter. 22-Tooth Clearing Blade is designed for dense thickets and saplings up to 64 mm (2.5 in.) diameter. A trimmer/brushcutter with a metal blade can cause serious injuries if handled improperly.
DPAS-2600 SAFETY Hedge Trimmer blades are sharp. Always wear gloves when adjusting cutting assembly. DO NOT stand hedge trimmer on end when adjusting cutting angle, otherwise serious injury may result. 1. 2. Place unit on a flat surface with blade guard (A) facing up. Assure stop switch is in the “STOP” position. A Grab blade adjustment handle (B) and compress blade lock levers (C) and (D) together. Rotate blade to desired position. Release the levers to lock the blade.
SAFETY 1. Loosen gear case clamping screw (A) and remove gear case locating screw (B). 2. Rotate cutter assembly 180° on drive shaft until locating hole in drive shaft is visible through locating hole in gear case. 3. Install gear case locating screw (B), and securely tighten all hardware. DPAS-2600 A B Hedge Trimmer blades are very sharp. Wear gloves to protect hands when rotating cutter assembly or serious personal injury may result.
DPAS-2600 DESCRIPTION DESCRIPTION Locate the safety decal(s) or etching(s) on your unit. Make sure they are legible and that you understand and follow the instructions. If a decal or etching cannot be read, replacement can be ordered from your ECHO dealer. Safety label is for example only. Your label might appear slightly different. 4 6 13 3 11 10 9 5 12 7 8 2 1. 1 Power Head 2. Throttle Handle - For Right Hand 3. Operator Presence Switch 4. Enable Button 5. - Button 6. + Button 7.
CONTENTS 9. DPAS-2600 Support Handle - For Left Hand 10. Upper Drive Shaft Assembly 11. Drive Shaft Coupler 12. Harness Ring 13. Clamping Knob CONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
DPAS-2600 ASSEMBLY ASSEMBLY Support Handle Installation Note: Label shows minimum spacing for support handle location. 1. If necessary, position support handle for comfortable operation and securely tighten screws. Power Head Shaft to Lower Shaft Assembly 1. Set Power Head/Shaft Assembly on a level surface. 2. Pull locater pin (A) out, and turn counterclockwise one-quarter turn to lock-out position. 3. Remove storage hook and cap from attachment drive shaft.
ASSEMBLY DPAS-2600 Temperature Information Recommended Ambient Temperatures: Charging Low Product (1) High Not Applicable Battery 39°F (4°C) 104°F (40°C) Charger 39°F (4°C) 104°F (40°C) (2)(3) Usage/Discharge Storage Low High Low High 32°F (0°C) 113°F (45°C) 32°F (0°C) 113°F (45°C) 32°F (0°C) 113°F (45°C) 32°F (0°C) 113°F (45°C) 32°F (0°C) 113°F (45°C) Not Applicable (1) Assumes the battery is just off the charger or stored at the temperature range noted for charger usage (39°
DPAS-2600 ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ASSEMBLY Do not cover the charger. Covering the charger will prevent it from cooling. Do not operate the charger in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Charger can produce sparks which may ignite the dust or fumes - there is a risk of explosion. Connect the charger only to the mains of voltage and frequency specified on the rating plate. Connect the charger only to an easily accessible wall outlet.
ASSEMBLY DPAS-2600 The battery comes partially charged from the factory and needs to be fully charged before first use. Charge the battery when it no longer produces sufficient power to operate the unit or when battery lights indicate that the battery is low. Note: Your charger might look different from those pictured. 1. Plug charger AC cord in the wall outlet. 2. Align ridges on battery with grooves on charger, and slide battery into charger. 3.
DPAS-2600 4. When charging is complete, LED will remain GREEN. See battery manual for charging time. 5. Verify battery is fully charged. Remove battery from charger, press battery charge status button (B), and check LED display. • One green light indicates that the battery has 1-24% charge. ASSEMBLY B • Two green lights indicate that the battery has 25-54% charge. • Three green lights indicate that the battery has 55-79% charge. • Four green lights indicate that the battery has 80-100% charge. 6.
ASSEMBLY 1. Make sure power to unit is turned off. 2. Align ridges (A) on battery with grooves in power head. Slide battery into power head. 3. Assure the battery latch (B) snaps into place and battery is secure before beginning operation. DPAS-2600 A B Assure battery latch is fully engaged before using unit. Battery Removal To remove battery, depress battery latch release (C) slide battery out of power head.
DPAS-2600 OPERATION OPERATION Starting Unit The attachment will operate when the battery is installed, the power indicator LED is lit, and the operator presence switch, lock off lever switch (if applicable), and power switch are engaged. Make sure the product is properly positioned to prevent loss of control and possible serious injury. Note: This model has three operating modes: low, medium, high. Use + (E) and - (F) buttons to switch between modes.
OPERATION DPAS-2600 When power to unit is turned on: • After 90 seconds of inactivity, unit will power itself off. • If power indicator LED remains lit, operation is normal. • If power indicator LED flashes once per second, the battery needs to be charged. • If power indicator LED flashes four times per second, there is a fault within the product. Turn power off to unit. Remove battery. Clear debris from around cutting attachment. Install battery. Turn power on to unit.
DPAS-2600 OPERATION Do not install blades on GT (Curved Shaft) trimmers. Operating Techniques - Nylon Line Head Nylon line heads may be used for trimming, scything, edging, and scalping of grass and light weeds. Units with Speed Feed® line heads ONLY: To advance trimmer line, tap trimmer head against the ground while the head is turning at normal operating speed. Trimming Feed the spinning line into the material to be cut.
OPERATION DPAS-2600 General • Debris flows in direction of line head rotation. Change line head position to assure debris flow is directed away from operator. • Keep cutting line away from wire fences to avoid entanglement. • Operate trimmer only with cutting head below knee height. Operating Techniques - Metal or Plastic Blade Brushcutter blades may be used to cut and trim a wide variety of materials. Refer to the blade selection section for determining the correct blade for the application.
DPAS-2600 ◆ ◆ ◆ ◆ OPERATION Blade thrust may occur when the spinning blade contacts an object that it does not immediately cut. Following proper cutting techniques will prevent blade thrust. Blade thrust can be violent enough to cause the unit and/or operator to be propelled in any direction, and possibly lose control of the unit. Blade thrust can occur without warning if the blade snags, stalls or binds. Blade thrust is more likely to occur in areas where it is difficult to see the material being cut.
OPERATION DPAS-2600 As shown in the illustration, a blade turning counterclockwise will cause the equipment to pull away from the operator if the point of cutting resistance is on the left side of the blade. If the point of cutting resistance is on the right side of the blade, the equipment will push back toward the operator. In both examples, the reactive force is in the opposite direction of blade rotation at the contact point where resistance occurs.
DPAS-2600 MAINTENANCE Inspect the blade for damage before proceeding. Sharpen teeth if dull, or replace blade if cracked, bent, missing teeth, or otherwise damaged. To prevent binding: • Keep blades sharp • Avoid excessive pressure during cuts • Don’t exceed cutting capacity of blade • Don’t use blades with damaged or missing cutting teeth • Don’t rock blades in cut MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings.
MAINTENANCE DPAS-2600 Level 3 = See your dealer. Click HERE or go to http://www.echo-usa.com/products/maintenance-kit Maintenance Intervals COMPONENT OR SYSTEM MAINTENANCE PROCEDURE Skill Level Daily Or Before Use Battery / Battery Compartment Inspect / Clean / Charge Screws / Nuts / Bolts Inspect / Tighten / Replace Drive Shaft 1 Grease 1 1 1 MAINTENANCE PROCEDURE NOTES: 1 Apply lithium based grease every 25 hours of use.
DPAS-2600 1. MAINTENANCE Release power switch and operator presence switch, and allow unit to stop. 2. Make sure power indicator LED is not illuminated. 3. Depress battery latch release (A) and slide battery out of power head. 4. A Use compressed air or a soft bristle brush to remove debris from battery and battery compartment. Lubrication Level 1. Parts Required: Lithium Based Grease. Drive Shaft 1. Loosen handle clamping screw (B) and slide throttle handle forward. B 2.
MAINTENANCE 3. Pull flex cable (D) out of shaft housing, wipe clean and recoat with 15 ml (0.5 oz.) grease. 4. Slide flex cable (D) back into shaft housing. DO NOT get dirt on flex cable. 5. Reassemble in reverse order. DPAS-2600 D Nylon Line Replacement Wear gloves or personal injury may result: ◆ Cut-off knife is sharp. ◆ Gearcase and surrounding area may be hot. Never use wire or wire-rope that can break off and become a dangerous “projectile.” Serious injury can occur. 1.
DPAS-2600 3. Insert one end of trimmer line into an eyelet, and push line equal distance through trimmer head. 4. Hold trimmer head while turning knob clockwise to wind line onto spool until about 13 cm (5 in.) of each line remains exposed. MAINTENANCE Trimmer head is now fully loaded and ready for operation. When the wear indicators located at the bottom of the Speed-Feed® head are worn smooth, or if holes appear, replacement of the cover or the entire Speed-Feed® head required.
MAINTENANCE 1. Press top of locking tabs (A) on both sides of Speed Feed® head to release cover (B) from knob (C). 2. Remove cover from knob. DPAS-2600 C A B Sharpening Metal Blades Metal blades are very sharp and can cause severe injuries, even if unit is off and blades are not moving. Avoid contact with blades. Wear gloves to protect hands. Several styles of metal blades are approved for use on the Brushcutter. The 8-tooth blade can be sharpened during normal maintenance.
DPAS-2600 1. 2. MAINTENANCE File each tooth at a 30° angle a specific number of times, e.g., four strokes per tooth. Work your way around the blade until all teeth are sharp. DO NOT file the ‘gullet’ (radius) of the tooth with the flat file. The radius must remain. A sharp corner will lead to a crack and blade failure. 30º 30º If an electric grinder is used, use care not to overheat teeth, do not allow tips/tooth to glow red or turn blue. DO NOT place blade in cooling water.
TROUBLESHOOTING DPAS-2600 TROUBLESHOOTING TROUBLESHOOTING CHART Problem Red Charger light flashes or does not light up Unit will not turn on Unit does not run when turned on Running time is too short 50 Cause Remedy Plug not connected to power outlet. Plug in charger. Battery pack not installed properly. Check the battery installation. Obstructed connection. Reinstall battery after removing obstructions. Fault in the charger. Consult your dealer. Fault in the battery pack.
DPAS-2600 STORAGE STORAGE Storage Do not store in an enclosure where combustible fumes may accumulate. Fire may result. When storing the product for long periods of time, ensure that the following preparations for storage are carried out. Unit Do not store your unit without performing protective storage maintenance which includes the following: 1. Turn power to unit off. 2. Remove battery. 3. Remove accumulation of dirt and debris from exterior of unit. 4. Tighten all screws and nuts. 5.
STORAGE DPAS-2600 Disposal Major plastic parts making up the product have codes showing their materials. The codes refer to the following materials; dispose of those plastic parts in accordance with local regulations. Materials Mark Material >PA6-GF< Nylon 6 - Glass fiber >PP-GF< Polypropylene - Glass fiber >PE-HD< Polyethylene >PP< Polypropylene • Battery contains lithium. Dispose of only at a designated collection point. • Lithium-ion batteries must be disposed of properly.
DPAS-2600 SPECIFICATIONS SPECIFICATIONS MODEL DPAS-2600 Length (without battery or trimmer attachment) 1082 mm (42.60 in.) Width (without battery or trimmer attachment) 215 mm (8.46 in.) Height (without battery or trimmer attachment) 184 mm (7.24 in.) Weight (without battery, or trimmer attachment) 2.6 kg (5.73 lb) Battery ECHO eFORCE™ 56V series batteries Type Li-Ion Battery voltage 56 V (rated 50.
SPECIFICATIONS DPAS-2600 * For best unit run time, use 0.095” SilentwistTM trimmer line. Other 0.095” line might shorten run time. DPAS-2600 Spindle Ratings Attachment No. Maximum Spindle Speed (RPM) 99944200540 5680 +/- 3% 99944200545 4444 +/- 3% 99944200615 7829 +/- 3% ECHO Optional Attachments The following ECHO Pro Attachment Series attachments have been verified by ECHO to be compatible for use with this powerhead.
DPAS-2600 SPECIFICATIONS COMPATIBLE ATTACHMENTS Curved Shaft Edger 99944200470 Straight Shaft Edger 99944200475 Bed Redefiner 99944200465 Std Hedge Trimmer 99944200486 Mid Reach Hedge Trimmer 99944200640 Articulating Hedge Trimmer 99944200596 1. For use with: Articulating Hedge Trimmer, Hedge Trimmer, and Power Pruner™ Attachments ONLY. COMPLIANT ATTACHMENTS Speed-Feed® Trimmer 99944200540 UL 62841-4-4; CSA C22.2 NO.
WARRANTY DPAS-2600 WARRANTY ––– WARRANTY Limited Warranty Statement for ECHO 56 Volt Handheld Products and Walk Behind Mowers sold in USA and Canada ECHO Incorporated warrants to the original retail purchaser that this ECHO brand 56 Volt outdoor product is free from defects in material and workmanship and agrees to repair or replace, at ECHO Incorporated’s discretion, any defective product free of charge within these time periods from the date of purchase: If the product is for homeowner use: • Units
DPAS-2600 PRODUCT REGISTRATION PRODUCT REGISTRATION Thank you for choosing ECHO Power Equipment Please go to http://www.echo-usa.com/Warranty/Register-Your-ECHO to register your new product on-line. It's FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Incorporated. Registering your purchase enables us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
DPAS-2600 ECHO Incorporated PRODUCT REGISTRATION 58 X7508230802 ©10/23 ECHO Incorporated
DPAS-2600 NOTES NOTES X7508230802 ©10/23 ECHO Incorporated 59
U56300013000 - U56300999999 ECHO INCORPORATED 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.
