Tus neeg siv phau ntawv
Table Of Contents
- Disclaimer
- 1 Product overview
- 2 Specification and parameters
- 3 Size and pins definition
- 4 Recommended circuit diagram
- 5 Hardware design
- 6 E108-Product test
- 7 Command format
- 7.1 GKC interface data format
- 7.2 GKC command
- 7.2. Response message
- 7.2.2 System reboot
- 7.2.3 Erase auxiliary information
- 7.2.4 Low power mode
- 7.2.5 Message interval configuration
- 7.2.6 Periodic low power mode
- 7.2.7 Set star search mode
- 7.2.8 Save star search mode
- 7.2.9 Serial port parameter setting
- 7.2.10 Set NMEA output
- 7.2.11 GPD document delete
- 7.2.12 Set NMEA serial port parameter
- 7.2.13 PPS configuration
- 7.2.14 Query message interval
- 7.2.15 Return message interval
- 7.2.16 Set NMEA output frequency
- 7.2.17 Query NMEA output frequency
- 7.2.18 Return the NMEA output frequency
- 7.2.19 Set reference coordinates
- 7.2.20 Query Reference Coordinate System
- 7.2.21 Return Reference Coordinate System
- 7.2.22 Query RTC time
- 7.2.23 Return RTC time
- 7.2.24 Set the speed threshold
- 7.2.25 Set HDOP Threshold
- 7.2.26 Get HDOP Threshold
- 7.2.27 Version number query
- 7.2.28 Return the current version number
- 7.2.29 Set location and time information
- 7.2.30 Set positioning mode
- 7.2.31 Query ID information
- 7.2.32 Return ID information
- 7.3 Support NMEA0183 protocol
- 8 GDP User Guidance
- 9 FAQ
- 10 Welding instruction
- 11 E108 Series
- 12 Packing for batch order
- Revision history
- About us
Chengdu Ebyte Electronic Technology Co.,Ltd. E108-GN User Manual
Copyright ©2012–2022，Chengdu Ebyte Electronic Technology Co.,Ltd.
32
9 FAQ
9.1 Communication range is too short
The communication distance will be affected when obstacle exists.
Data lose rate will be affected by temperature, humidity and co-channel interference.
The ground will absorb and reflect wireless radio wave, so the performance will be poor when testing near ground.
Sea water has great ability in absorbing wireless radio wave, so performance will be poor when testing near the sea.
The signal will be affected when the antenna is near metal object or put in a metal case.
Power register was set incorrectly, air data rate is set as too high (the higher the air data rate, the shorter the
distance).
The power supply low voltage under room temperature is lower than 2.5V, the lower the voltage, the lower the
transmitting power.
Due to antenna quality or poor matching between antenna and module.
9.2 Module is easy to damage
Please check the power supply source, ensure it is in right range. Voltage higher than max value will damage the
module.
Please check the stability of power source, the voltage cannot fluctuate too much.
Please make sure antistatic measure are taken when installing and using, high frequency devices have electrostatic
susceptibility.
Please ensure the humidity is within limited range, some parts are sensitive to humidity.
Please avoid using modules under too high or too low temperature.
9.3 BER(Bit Error Rate) is high
There are co-channel signal interference nearby, please be away from interference sources or modify frequency and
channel to avoid interference;
Poor power supply may cause messy code. Make sure that the power supply is reliable.
The extension line and feeder quality are poor or too long, so the bit error rate is high;