Product Data Sheet RER175-42/18/2TDMP Product Data Sheet RER175-42/18/2TDMP The engineer's choice
Product Data Sheet RER175-42/18/2TDMP RER175-42/18/2TDMP INDEX 1 General ............................................................................................................................................................... 3 2 Mechanics .......................................................................................................................................................... 3 2.1 2.2 3 Operating Data ............................................................................
Product Data Sheet RER175-42/18/2TDMP 1 General Fan type Rotating direction looking at rotor Airflow direction Bearing system Mounting position - shaft 2 Mechanics 2.1 General Depth Diameter Mass Housing material Impeller material 2.
Product Data Sheet RER175-42/18/2TDMP The auxilliaries shown on the schematic diagram (which are required for the intended use) are not part of our delivery.
Product Data Sheet RER175-42/18/2TDMP 3 Operating Data 3.1 Electrical Interface - Input Control input PWM Features PWM - Frequency 1 kHz - 10 kHz typical: 2 kHz Characteristics Schematics The shown pull-up resistor R1 to the internale reference voltage (+5V) has a resistance of 4.7kOhm. Transistor requirements: Vce max.= >12 V; I sink max. = >5 mA; Vce sat.
Product Data Sheet RER175-42/18/2TDMP Speed control: By pulse-width modulation (PWM) 0 ... 100% Frequency = 2 kHz (1 - 10 kHz) Information to the curve PWM: 0% - <7% PWM: 0 1/min 7% PWM: 800 1/min (Fan on, comming from 0% PWM) 7% - 10% PWM: 800 1/min (corresponding to min. speed) 10% - 90% PWM: linear increasing curve 90% - 100% PWM: 4.800 1/min (corresponding to max. speed) 7% - >5% PWM: linear decreasing curve (comming from 100% PWM) 5% PWM: 600 1/min or 0 1/min (Fan off, comming from 100% PWM) 3.
Product Data Sheet RER175-42/18/2TDMP 3.3 Electrical Interface - Output Tacho type Features Tacho operating voltage Tacho signal Low Tacho signal High Maximum sink current External resistor Tacho frequency Tacho isolated from motor Slew rate /2 (open collector) Note UBS US low US high Isink Values <= 60,0 V I sink: 2 mA <= 0,4 V I source: 0 mA <=60,0 V <= 20 mA External resistor Ra from UBS to US required. All voltages measured to GND. (6 x n) / 60 480 Hz @ 4.
Product Data Sheet RER175-42/18/2TDMP Locked rotor protection Locked rotor current at UN Clock signal at locked rotor Extended Downtime Internal fuse Voltage control *) Auto restart Iblock approx. 2.000 mA t3 / t4 typical: 7 s / 10,0 s t5: 40 s after 4 start-up tests Littelfuse NANO2 > Very Fast-Acting > 451/453 Series 6,3A / 125V (Art.No.: 045106.
Product Data Sheet RER175-42/18/2TDMP 3.6 Aerodynamics Measurement conditions: Measured with a double chamber intake rig acc. to DIN EN ISO 5801. Normal air density = 1,2 kg/m3; Temperature 23°C +/ - 3°C; In the intake and outlet area should not be any solid obstruction within 0,5 m. Motor shaft horizontal. The information is only valid under the specified test conditions and may be changed by the installation conditions.
Product Data Sheet RER175-42/18/2TDMP 02/01/2019 page 10 of 13
Product Data Sheet RER175-42/18/2TDMP 3.7 Sound Data Measurement conditions: Sound pressure level: 1 meter distance between microphone and the air intake. Sound power level: Acc. to DIN 45635 part 38 (ISO 10302) Measured in a semianchoic chamber with a background noise level of Lp(A) < 5 dB(A) For further measurement conditions see chapter aerodynamics. a.) Operation condition: 4.
Product Data Sheet RER175-42/18/2TDMP 5 Safety 5.1 Electrical Safety Dielectric strength DIN EN 60950 (VDE 0805) and DIN EN 60335 (VDE 0700) A.) Type test Measuring conditions: After 48h of storage at 95% R.H. and 25°C. No arcing or breakdown is allowed! All connections together to ground. B.) Routine test Measuring conditions: At indoor climate. No arcing or breakdown is allowed! All connections together to ground. Isolation resistance Measuring conditions: After 48h of storage at 95% R.H.