CONTROL UNIT FOR EBERSPÄCHER PARKING HEATERS A WORLD OF COMFORT INSTALLATION INSTRUCTIONS O P E RAT IN G IN S T R UCTIO N S E AS Y S TA RT R E MO TE EN OPERATING INSTRUCTIONS V E H I C L E H E AT E R S | T E C H N I C A L D O C U M E N TAT I O N
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION CONTENTS CHAPTER CHAPTER TITLE CHAPTER CONTENTS 1 2 PAGE INTRODUCTION Please read first 4 Safety information 4 Range of uses 4 Statutory regulations 5 EU Declaration of Conformity 5 General information 5 OVERVIEW EasyStart Remote mobile unit 6 Button functions 6 button ON 6 button OFF 6 LED indications 6
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 3 CONTENTS 3 4 5 6 OPERATION AND SETTING/ADJUSTMENT Notes on operation and setting 8 Switch on the heater 9 Switch off heater 9 Query the operating state of the heater 10 Permanently change the operating time 10 Switch to HEATING or VENTILATION 12 Function pushbuttons 13 MAINTENANCE Charged status of the mobile unit's battery 14 Replacing the battery 14 WHAT TO DO IF …? In the event of a fault the following flashing signals are poss
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 1 I N T R O D U C T IO N PLEASE READ FIRST Before you start to set and use the timer, always read through these operating instructions carefully. These operating instructions contain important information that you require for to set and use the timer. Please keep these operating instructions in a safe place for subsequent reference. Only use the recommended battery and original spare parts (from page 14).
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 5 1 Introduction STATUTORY REGULATIONS RETURN / DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT IN ACCORDANCE WITH § 4 PARAGRAPH 1 ALT FZ-VO (END OF LIFE VEHICLE REGULATIONS) As a part of the vehicle, when the vehicle is handed over to a recognised waste collection body, a recognised returns body or a recognised dismantling firm, the radio remote control must be placed in the vehicle for return in accordance with Art 4 Paragraph 1 Alt Fz-VO.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 2 OVERVIEW EASYSTART REMOTE MOBILE UNIT LED INDICATIONS The mobile unit of the EasyStart Remote radio remote control can be used to switch the heater on and off. Further, it can be used to make the necessary settings for operation of the heater. DATA TRANSMISSION PLEASE NOTE! The type of LED displays possible differs depending on the installed heater and feature options. LED indicator lights up green.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 7 2 O verview PLEASE NOTE! Possible LED indications such as alternating red-green flashing, red flashing or continuously lit red are described in the chapter “What to do if …?” from page 15. Entries can also be made during the flashing stations, but not during the data transmission.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 O PE R AT I O N A N D SETTING /AD J USTMENT NOTES ON OPERATION AND SETTING PERMANENTLY CHANGE THE OPERATING TIME ACTUATE THE MOBILE UNIT 10, 20, 30, 40, 50 or 60 minutes can be set as the operating time (factory setting is 30 minutes). Each press of the button results in an action, which is indicated by flashing. The flashing indicator goes out automatically.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 9 3 O peration and setting /adjustment SWITCH ON THE HEATER SWITCH OFF HEATER HEATING OR VENTILATION HEATING OR VENTILATION Press the button, the connection is set up with the stationary unit is. Press the button, the connection is set up with the stationary unit is. Data transmission Data transmission LED: lights up green LED: lights up green LED: flashes 12x green The heater is switched on.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 O PE R AT IO N A ND SETTING /AD J USTMENT QUERY THE OPERATING STATE OF THE HEATER Press the button, the connection is set up with the stationary unit is. Data transmission LED: lights up green PERMANENTLY CHANGE THE OPERATING TIME Keep the button pressed until “CURRENT OPERATING TIME WILL BE DISPLAYED AS FLASHING” appears. PLEASE NOTE! A switched on heater is switched off with this setting.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 11 3 O PE R AT IO N A ND SETTING /AD J USTMENT SELECTION OF THE OPERATING TIME 10 minutes operating time LED: flashes 1x red Confirm the selected operating time in the pauses between the respective flashing sequences by pressing the button. Data transmission LED: lights up green 20 minutes operating time LED: flashes 2x red LED: flashes e.g.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 O peration and setting /adjustment SWITCH TO HEATING OR VENTILATION PLEASE NOTE! This function is only possible if the heater supports the VENTILATION function. A switched on heater is switched off with this setting. button pressed until “CURRENT Keep the OPERATING TIME IS DISPLAYED” appears. Data transmission PLEASE NOTE! Make the following setting within 30 seconds button. of letting go of the Press the button again; the operating mode is changed.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 13 3 O peration and setting /adjustment FUNCTION PUSHBUTTONS The following activities can be executed with the buttons installed in the vehicle: Start heating mode, the last entry made for the operating time applies (button LED On). Switch off heater mode (button LED Off) Teach the mobile unit, see installation instructions.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 4 MA I N T E N A N C E CHARGED STATUS OF THE MOBILE UNIT'S BATTERY LED: lights up red for 4 seconds Insert new battery. The battery has been correctly inserted if the plus pole symbol and the type designation of the battery can be read. Put on the battery compartment cover and latch into place.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 15 5 WH AT T O D O I F …? IN THE EVENT OF A FAULT THE FOLLOWING FLASHING SIGNALS ARE POSSIBLE: LED INDICATOR POSSIBLE CAUSES REMEDY / CUSTOMER or On pressing the button, slow redflashing 5x Fault heater. Visit your vehicle workshop. The EasyStart Remote has been disconnected from the power supply and then reconnected. Teach mobile unit as described in the installation instruction. Wait until the automatic detection has finished.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 5 What to do if …? THE FOLLOWING FAULTS ARE POSSIBLE FAULT POSSIBLE CAUSES REMEDY /CUSTOMER The mobile unit cannot be activated Battery dead. Replace battery (see page 14). No battery inserted. Insert battery (see page 14). Battery inserted wrong way around. Insert battery correctly (see page 14). LED at the button flashes Stationary unit is in learn mode.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 17 6 SERVICE HOTLINE If you have any technical questions, a problem with the EasyStart Remote radio remote control or the heater, dial the following service phone number from within Germany. Hotline: 0800 1234300 Fax hotline: 01805 262624 Outside of Germany, please contact the respective Eberspächer national representative.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 19
Printed in Germany Eberspächerstraße 24 73730 Esslingen Hotline: 0800 1234300 Fax hotline: 01805 262624 info@eberspaecher.com www.eberspaecher.com Subject to change without notice © Eberspächer Climate Control Systems GmbH & Co. KG GmbH & Co. KG 07.
