CONTROL UNIT FOR EBERSPÄCHER PARKING HEATERS A WORLD OF COMFORT INSTALLATION INSTRUCTIONS QUICK START GUIDE O P E RAT IN G I N S T R U CTION S E A S Y S TA RT R E MO TE + EN OPERATING INSTRUCTIONS V E H I C L E H E AT E R S | T E C H N I C A L D O C U M E N TAT I O N
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION CO N T E N T S CHAPTER CHAPTER TITLE CHAPTER CONTENTS 1 2 3 PAGE INTRODUCTION Please read first 4 Safety information 4 Range of uses 4 Statutory regulations 4 EU Declaration of Conformity 4 General information 5 OVERVIEW EasyStart Remote+ mobile unit 6 Button functions 6 LONGPRESS button 6 SHORTPRESS button 6 LONGPRESS button 6 SHORTPRESS button 6 Press button 1x / keep pressed 6 Press butto
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 3 CO N T E N T S 4 5 Heating OFF with LONGPRESS 11 Heating ON with SHORTPRESS and with settings 12 Heating OFF with SHORTPRESS 13 Change the temperature setpoint and / or the operating time during operation 13 Set ventilation ON with SHORTPRESS, if applicable set the operating time 15 Ventilation OFF with LONGPRESS 16 Ventilation OFF with SHORTPRESS 16 Add-on unit ON – e.g.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 1 I N T R O D U C T ION PLEASE READ FIRST Before you start to set and use the timer, always read through these operating instructions carefully. These operating instructions contain important information that you require for to set and use the timer. Please keep these operating instructions in a safe place for subsequent reference.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 5 1 Introduction GENERAL INFORMATION The mobile unit of the EasyStart Remote+ radio remote control has a simple control structure. All functions can be set and, if necessary, changed with only 4 buttons. The pulses of the mobile unit have a range of up to 1000 metres outdoors (direct visual contact). External interference, local conditions and high building density in the surrounding area shorten the range.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 2 O V E R V IE W EASYSTART REMOTE+ MOBILE UNIT The mobile unit of the EasyStart Remote+ radio remote control can be used to make the necessary settings for operation of the heater and / or the addon unit. BUTTON FUNCTIONS LONGPRESS button The button must be pressed for longer than 2 seconds. The heater is switched on immediately if ON or OFF appears in the display (except if programming is running or while making settings).
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 7 3 O PE R AT I O N A N D SETTIN G /AD J USTME NT NOTES ON OPERATION AND SETTING ACTIVATE MOBILE UNIT Before each operation or setting, a connection must be established between the mobile unit and the stationary unit. To do this, press or button, a transmitting antenna appears in the display. FLASHING SYMBOL / FLASHING VALUE A flashing symbol can be activated with the button in the menu bar of the Main menu.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment SETTING THE OPERATING TIME ADD-ON UNIT The operating time can be set individually using the An add-on unit can be e.g. a second heater or parking air conditioning. Further, it is also possible to combine a heater with a fan; the fan is then used for air distribution in the vehicle interior. A heater and the add-on unit can be operated simultaneously or independently of each other. or button.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 9 3 Operation and setting /adjustment MAIN MENU STATUS AREA If no menu item is activated, the current time and, if an (optional) temperature sensor is connected, the temperature in the vehicle interior are displayed in the status area. Start display: Time, e.g. 17:30 Temperature in the vehicle interior, e.g. 21 °C. Menu bar 17:30 21 °C Status area MENU BAR The following menu items can be selected.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment START DISPLAY FOLLOWING ACTIVATION OF THE MOBILE UNIT 17:30 21 °C If no menu item is activated, the Start display appears with a flashing heater symbol in the Menu bar, with the current time and the actual temperature in the status area. Other possible actions are: HEATING IMMEDIATELY with LONGPRESS.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 11 3 Operation and setting /adjustment HEATING IMMEDIATELY WITH LONGPRESS (WITHOUT SETTINGS) Press the LONGPRESS button for longer than 2 seconds. Following successful data transmission – heater ON. HEATING OFF WITH LONGPRESS LONGPRESS button for longer than Press the 2 seconds. Following successful data transmission – heater OFF. 21 °C Off 30 min 21 °C Display for air heaters in continuous heating mode (factory setting).
08:30 120 min 12 | VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment HEATING ON WITH SHORTPRESS AND WITH SETTINGS Press the or button to activate the mobile unit. Following successful data transmission the Start display appears. 17:30 SETTING THE OPERATING TIME or button to set the If necessary, use the operating time. Operating time setting range: Min 10 – max 120 min in 1 min. increments, continuous heating mode is possible for air heaters.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 13 3 Operation and setting /adjustment HEATING OFF WITH SHORTPRESS Press the or button to activate the mobile unit. Following successful data transmission the HEATING menu item is displayed. Press the SHORTPRESS button for less than 2 seconds. Heater OFF. Off 21 °C The display lighting goes out 10 seconds after H EATING OFF is displayed. PLEASE NOTE! The heater switches off, an active add-on unit remains in operation.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment SETTING THE OPERATING TIME or button to set the If necessary, use the operating time. Operating time setting range: Min 10 – max 120 min in 1 min. increments, continuous heating mode is possible for air heaters. 60 min Press the button to confirm the operating time. The operating time is changed once. 60 min 21 °C Display for air heaters in continuous heating mode.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 15 3 Operation and setting /adjustment SET VENTILATION ON WITH SHORTPRESS, IF APPLICABLE SET THE OPERATING TIME Press the or button to activate the mobile unit. Following successful data transmission the Start display appears. Use the or button to select the ventilation symbol in the Menu bar. The operating time is changed permanently.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment VENTILATION OFF WITH LONGPRESS VENTILATION OFF WITH SHORTPRESS Press the Press the or button to activate the mobile unit. Following successful data transmission the V ENTILATION menu item appears in the display. LONGPRESS button for longer than 2 seconds Heater OFF. Press the SHORTPRESS button for less than 2 seconds. Heater OFF.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 17 3 Operation and setting /adjustment ADD-ON UNIT ON – E.G. ACTIVATE THE HEATING FUNCTION FOR A 2ND HEATER Press the or button to activate the mobile unit. Following successful data transmission the Start display appears. Use the or in the Menu bar. Off button to select the 21 °C symbol 08:30 120 min Confirm the ADD-ON UNIT menu item by pressing the button. Use the or button to select the symbol.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment Display for air heaters in continuous heating mode (factory setting). ADD-ON UNIT ON – E.G. ACTIVATE THE VENTILATION FUNCTION FOR A 2ND HEATER Press the or button to activate the mobile unit. Following successful data transmission the Start display appears. ∞ PLEASE NOTE! After switching on, “On” is displayed for 2 sec and for air then the remaining operating time or heaters.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 19 3 Operation and setting /adjustment PLEASE NOTE! The following setting or confirmation is absolutely necessary. SETTING THE OPERATING TIME or button to set the If necessary, use the operating time. Operating time setting range: Min 10 – max 120 min in 1 min. increments, continuous VENTILATION mode possible for air heaters. 60 min Press the button to confirm the operating time. The operating time is changed permanently. Heater ON.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment ADD-ON UNIT OFF WITH LONGPRESS ADD-ON UNIT OFF WITH SHORTPRESS Press the Press the LONGPRESS button for longer than SHORTPRESS button for less than 2 seconds 2 seconds. Add-on unit OFF. Add-on unit OFF. Off 21 °C Off 21 °C The display lighting goes out 10 seconds after ADDON-UNIT OFF is displayed. The display lighting goes out 10 seconds after ADDON-UNIT OFF is displayed.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 21 3 Operation and setting /adjustment GENERAL INFORMATION ON PROGRAMMING THE PRESET TIME SETTING) The programming of the preset time is carried out in menu item . Under the following conditions the preselected heating mode is not started on the current day. The mobile unit of the EasyStart Remote+ can be The current day and the preselected day are identical. The current time lies within the time period, departure time minus operating time.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment AUTOMATIC OPERATING TIME CALCULATION (for water heaters only) For water heaters with a connected temperature sensor the heating start is calculated automatically depending on the measured room temperature and the selected heating level (ECO or HIGH). The operating time can lie between 10 and 60 minutes; operation is always ended 5 minutes after the programmed departure time.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 23 3 Operation and setting /adjustment PROGRAM PRESET TIMES Program memory P1 display, factory setting. Press the or button to activate the mobile unit. Following successful data transmission the Start display appears. Use the or the Menu bar. button to select the symbol in Display, if no preselection is activated. 1 2 3 Display, if a preselection is activated e.g. P2. 1 2 3 Confirm the PROGRAM menu item by pressing the button.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment SELECTING THE WEEKDAY GROUP / WEEKDAY 2 Use the or button to select the weekday group Mon – Fri, Sat – Sun, Mon – Sun or a weekday Mon, Tue, Wed, Thu, Fri, Sat, Sun. Mi. 21 °C 06 : 30 60 min. PLEASE NOTE! button to After editing the program, press the return to the PROGRAM / PRESELECTION menu item or wail until the display lighting goes out. 2 Mi. Press the button to confirm the setting.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 25 3 Operation and setting /adjustment SELECTING THE OPERATING MODE Use the bol or the or button to deselect the symbol. sym- Select ECO heating level or HIGH heating level using the or button. 2 2 ECO 2 2 HIGH Press the Confirm the HEATING or VENTILATION function by pressing the button. button to confirm the heating level.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment ACTIVATING THE PROGRAM MEMORY 2 On Off Press the button to confirm the “On” setting. DEACTIVATING THE PROGRAM MEMORY Use the Mi. 21 °C 06 : 30 60 min. PLEASE NOTE! button to After editing the program, press the return to the PROGRAM / PRESELECTION menu item or wail until the display lighting goes out. Do not press the button, as otherwise the “On” setting switches to “Off” and vice versa.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 27 3 Operation and setting /adjustment SETTINGS or Use the SETTING THE TIME or button to activate the mobile Press the unit. Following successful data transmission the Start display appears. Use the or in the Menu bar. button to select the symbol button to set the minutes. 06 : 30 Press the button to confirm the setting. PLEASE NOTE! Do not press the button, as otherwise SET THE TIME appears in the display again. Mo.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 3 Operation and setting /adjustment SETTING THE WEEKDAY Press the or button to activate the mobile unit. Following successful data transmission the Start display appears. Use the or in the Menu bar. button to select the symbol Mo. 10:30 Confirm the SETTINGS menu item by pressing the button. The SET THE TIME is displayed. or Use the DAY symbol. Press the Use the button to select the WEEK- button to confirm the setting.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 29 3 Operation and setting /adjustment SETTING THE TIME FORMAT Press the or button to activate the mobile unit. Following successful data transmission the Start display appears. Use the or in the Menu bar. button to select the 24 h symbol Press the button to confirm the time format. PLEASE NOTE! Do not press the button, as otherwise SET THE TIME FORMAT appears in the display again. Mo. 10:30 Confirm the SETTINGS menu item by pressing the button.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 4 M A IN T E N A N CE CHARGED STATUS OF THE MOBILE UNIT'S BATTERY REPLACING THE BATTERY The battery charge status is shown in the Start display of the SETTINGS menu item. Open the battery compartment. With your thumb in the position show, push down on the battery compartment cover and then push it towards the front. Mo.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 31 5 W H AT T O D O IF …? IN THE EVENT OF A FAULT THE FOLLOWING DISPLAYS ARE POSSIBLE DISPLAY Pair mode Add DESCRIPTION REMEDY / CUSTOMER Automatic detection is active. The EasyStart Remote+ has been disconnected from the power supply and then reconnected. Wait until the automatic detection has finished, then set the time and weekday, see page 27 and 28. Battery dead.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION 5 W hat to do if …? DISPLAY DESCRIPTION REMEDY / CUSTOMER Distance between the mobile unit and vehicle too large or at the range limit. Change the position relative to the vehicle e.g. hold mobile unit higher or move it to the side. Reduce distance from vehicle. Dense buildings between the mobile unit and vehicle. Reduce distance. If possible, reinstate visual contact with the vehicle. Mobile unit has not been taught.
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 33 6 SERVICE HOTLINE If you have any technical questions, a problem with the EasyStart Remote+ radio remote control or the heater, dial the following service phone number from within Germany. Hotline: 0800 1234300 Fax hotline: 01805 262624 Outside of Germany, please contact the respective Eberspächer national representative.
| VEHICLE HEATERS – TECHNICAL DOCUMENTATION
VEHICLE HEATERS – TECHNICAL DOCUMENTATION | 35
Eberspächer Climate Control Systems GmbH & Co. KG Eberspächerstraße 24 73730 Esslingen Hotline: 0800 1234300 Fax hotline: 01805 262624 info@eberspaecher.com www.eberspaecher.com 22 1000 34 17 03 EN 07.2014 Subject to change without notice © Eberspächer Climate Control Systems GmbH & Co.
