Assembly Instructions Sheet
1of2
,.
..
IntegratedLED15W
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Package Contents
A
B
Crossbar
x1
Lock Washer
x1
Hex Nut
x1
Nipple
x1
STEP 1 Install the Crossbar to the junction box-
.
A. Attach the Crossbar (A) to the Outlet Box with the head of the Green
Ground Screw facing you. Secure it with Outlet Box Screws (not
included), tighten until snug
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
STEP 2 Install the
Nipple to the Crossbar
-
A. Thread the Hex Nut (C)
to the middle of the
Nipple (D). Place the
Lock Washer (B) over
the Nipple (D) and then
thread the Nipple (D)
into the Crossbar (A)
until the Nipple (D) is
about 0.375” above the
Crossbar (A).
B. Place the ceiling
canopy and Fixture
Body (G) over the
Nipple (D) against the
ceiling to determine the
correct position of the
Nipple (D). Thread the
Mounting Cap (F) onto
the Nipple (D). Adjust
the Nipple (D) to allow
(Step 2 Continued)
the ceiling canopy and Fixture Body (G) to rest against the ceiling
when held in place by the Mounting Cap (F).
C. Remove the Mounting Cap (F) and the Fixture Body (G). Tighten the
Hex Nut (C) against the Crossbar (A) to secure in place.
Figure 2
C
D
Rubber Washer
x1
E
Mounting Cap
x1
F
Fixture
Body
x1
G
A
A
B
C
D
F
G
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare,orGreen
Ground wire
from outlet box
Ground wire
from fixture
Bare,orGreen
Ground wire
from outlet box
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar
STEP 4 - Install Fixture Body
A. Place the ceiling canopy and Fixture Body (G) over the end of the
Nipple (D). Pass the Rubber Washer (E) over the Nipple (D) and
D
F
E
G
ROTATE
ROTATE
Figure 4
thread the Mounting Cap
(F) onto the Nipple (D) to
secure the Fixture Body
(G). Hand tighten until
snug.
B. Rotate the lamp to achieve
your desired directions.
Your fixture is now
assembled and ready to
use. Enjoy!
Assembly Instruction Sheet