Firmware Manual
9000X AF Drives
4-4 For more information visit: www.eaton.com
MN04004001E
August 2010
Multi-Step Speed Control Application
Basic Parameters (Control Keypad: Menu M1
➔
G1.1)
Table 4-3: Basic Parameters — G1.1
Code Parameter Min. Max. Unit Default Cust ID Note
P1.1.1 Min frequency 0.00 Par. 1.1.2 Hz 0.00 101
P1.1.2 Max frequency Par. 1.1.1 320.00 Hz 60.00 102 NOTE: If f
max
> than the
motor synchronous speed,
check suitability for motor
and drive system.
P1.1.3 Acceleration time 1 0.1 3000.0 s 3.0 103
P1.1.4 Deceleration time 1 0.1 3000.0 s 3.0 104
P1.1.5 Current limit 0.4 x I
H
2 x I
H
AI
L
107
P1.1.6
Nominal voltage of the
motor
180 690 V P: 230V
P: 460V
P: 575V
110
P1.1.7
Nominal frequency of
the motor
30.00 320.00 Hz 60.00 111 Check the rating plate of the
motor.
P1.1.8
Nominal speed of the
motor
300 20 000 rpm 1720 112 The default applies for a
4-pole motor and a nominal
size frequency converter.
P1.1.9
Nominal current of the
motor
0.4 x I
H
2 x I
H
AI
H
113 Check the rating plate of the
motor.
P1.1.10
Power Factor 0.30 1.00 0.85 120 Check the rating plate of the
motor.
P1.1.11
Local control place 0 3 1 171 1 = I/O Terminal
2 = Keypad
3 = Fieldbus
P1.1.12
Remote control place 0 3 1 172 1 = I/O Terminal
2 = Keypad
3 = Fieldbus
P1.1.13
Local control reference 0 3 2 173 0 = AI1
1 = AI2
2 = Keypad
3 = Fieldbus
P1.1.14
Remote control
reference
0 3 0 174 0 = AI1
1 = AI2
2 = Keypad
3 = Fieldbus
P1.1.15 Motor Id 0 2 0 631 0 = Not user
1 = V/Hz
2 = V/Hz with boost
P1.1.16 V/Hz opt 0 1 0 109 0 = Not used
1 = Automatic torque boost
P1.1.17 Jogging speed pref. 0.00 Par. 1.1.2 Hz 0.00 124
P1.1.18 Preset speed 1 0.00 Par. 1.1.2 Hz 5.00 105 Multi-step speed 1
P1.1.19 Preset speed 2 0.00 Par. 1.1.2 Hz 10.00 106 Multi-step speed 2
P1.1.20 Preset speed 3 0.00 Par. 1.1.2 Hz 12.50 126 Multi-step speed 3
P1.1.21 Preset speed 4 0.00 Par. 1.1.2 Hz 15.00 127 Multi-step speed 4
P1.1.22 Preset speed 5 0.00 Par. 1.1.2 Hz 17.50 128 Multi-step speed 5
P1.1.23 Preset speed 6 0.00 Par. 1.1.2 Hz 20.00 129 Multi-step speed 6