Technical data

February 2007
CA05001001K For more information visit: www.EatonElectrical.ca
59
PLC, I/O & Communications Products
IT. Connect
Communication Adapters (D77D Series) — EtherNet/IP Adapter
Product Description
The Cutler-Hammer
®
Intelligent Tech-
nologies (IT.) EtherNet/IP (D77D-EIP)
from Eaton’s electrical business has
greatly increased the functionality of
Cutler-Hammer IT. communicating
products, allowing monitoring and
control for IT. I/O and IT. motor control
devices. The adapter concentrates all
data from these devices into a single
EtherNet/IP node.
The EtherNet/IP Adapter is a slave
device on EtherNet/IP and a master on
QCPort.
To simplify the configuration of the
D77D-EIP, a simple auto-configure
button press sets the system up for
default operation. This automatically
configures the EtherNet/IP assemblies
to the QCPort system devices
Application Description
In a typical EtherNet/IP Adapter appli-
cation, the D77D-EIP connects directly
to EtherNet/IP, and resides in a system
with IT. I/O and other communicating
motor controls. The data from these
IT. devices is assembled into input and
output assemblies before being pre-
sented to EtherNet/IP.
Cat. No. D77D-EIP
Features, Functions and Benefits
■ Communication to EtherNet/IP
consuming one address
■ Supports Boot P, DHCP and static
IP addressing
■ 10 BaseT Connection
■ Provides for control of all IT. com-
municating devices connected to
the network adapter
■ Single button press auto configures
the gateway, setting up the system
for default operation
■ Advanced configuration using
CH Studio
■ Provides for backplane and inter-
connect cable connections to
QCPort
■ Two independent QCPort (commu-
nication) ports
■ Powered from QCPort
■ Isolated from EtherNet/IP
■ Status LEDs for EtherNet/IP, QCPort
and module health
■ Provides for configuration of QCPort
devices over EtherNet/IP
■ Small package size
■ DIN rail mountable
Standards and Certifications
Approvals
Table 89. Approvals/Certifications
Technical Data and Specifications
Table 90. Environmental Ratings Table 91. EtherNet/IP Specifications
Description Specification
Electrical/EMC
ESD Immunity (IEC 61000-4-2) ± 8 kV air, ± 4 kV contact
Radiated Immunity (IEC 61000-4-3) 10V/m 80 – 1,000 MHz, 80% amplitude modulation @ 1 kHz
Fast Transient (IEC 61000-4-4) ± 2 kV supply and control, ± 1 kV communications
Surge (IEC 61000-4-5) ± 1 kV line-to-ground, ± 2 kV line-to-line
RF Conducted (IEC 61000-4-6) 10V, .15 – 80 MHz
Magnetic Field (IEC 61000-4-8) 30A/m, 50 Hz
Other Approvals
Ingress Protection Code IP20
Radiated and Conducted Emissions EN 5011 Class A
Agency Certifications UL 508, CUL (CSA C22.2 No. 14), CE (Low Voltage Directive),
Modbus Conformance Tested
Description Specification
Transportation/Storage
Temperature -58° – 176°F (-50° – 80°C)
Humidity 5 – 95% non-condensing
Operating
Temperature -13° –149 °F (-25° – 65°C)
Humidity 5 – 95% non-condensing
Altitude Above 6,600 ft. (2,000m)
consult factory
Shock
(IEC 68-2-27)
15G any direction for
11 mS
Vibration
(IEC 68-2-6)
5 – 150 Hz, 5G .7 mm
maximum peak-to-peak
Pollution Degree 2
Description Specification
Connections 10 BaseT
I/O Size 504 bytes Input
504 bytes Output
Baud Ethernet 10 Megabit
Addressing Ethernet – Boot P, Static IP
or DHCP
QCPort Channels 2 Independent
Channels