Eaton® Network Card-MS User’s Guide
Class B EMC Statements FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Special Symbols The following are examples of symbols used on the UPS or accessories to alert you to important information: RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol. CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for additional information, such as important operating and maintenance instructions. This symbol indicates that you should not discard the UPS or the UPS batteries in the trash.
Table of Contents 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking the Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Checklist. . . . .
Table of Contents 4 5 6 7 Environmental Monitoring Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environment Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environment Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 49 50 USING THE TELNET/SSH/CLI INTERFACE . . . . . . . . . . . . . . . . . . .
Table of Contents 8 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 9 SERVICE AND SUPPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Two-Year Limited Warranty (US and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network Card-MS . . . . . . . . . . . . . . . .
Chapter 1 Introduction The Eaton® Network Card-MS works with Eaton UPS Management Software to monitor, manage, and protect uninterruptible power supplies (UPSs) through standard Web pages, a Network Time Protocol (NTP) server, and Secure Sockets Layer (SSL) security protocol. The Network Card-MS can support up to five connected browsers at a time, or three with SSL protocol.
Introduction - Chinese Simplified - Japanese - Korean - Chinese Traditional - Russian - Czech l Online Help (English only) l Card firmware updated through the network l Fast Ethernet 10/100 MB compatibility with auto-negotiation on the RJ-45 port l Recording of events and measurements in the card log l Connection to the card with straight Category 5 RJ-45 network cables [maximum card distance is 20m (65 ft)] l Can be installed while the UPS is online, maintaining the highest system availability
Chapter 2 Getting Started This chapter explains: l Unpacking the card l Installing and connecting the card l Installing the optional Environmental Monitoring Probe (EMP) l Configuring and the card Unpacking the Card Verify the package contents: l Network Card-MS l Serial cable l Installation instructions Installation Checklist 1. 2.
Getting Started Card Details 1 4 6 5 2 3 1. Ethernet Port (10/100BaseT) 2. ACT LED (green) 3. 100M LED (orange) 4. Settings/Sensor Port 5. UPS Data LED (green) 6. RS232 LED (orange) Figure 2. Network Card-MS Details Table 1.
Getting Started Card Defaults Table 2 lists the Network Card-MS default parameters. Table 2. Default Parameters Function On Parameter Default Value Possible Values Network IP Address 192.168.1.2 Network IP address Subnet Mask 255.255.0.0 Network IP address Gateway Address 0.0.0.
Getting Started Installing the Card The Network Card-MS can be installed in any Eaton UPS equipped with a communication bay without turning off the UPS or disconnecting the load. To install the Network Card-MS: 1. Remove the communication bay cover from the UPS. Retain the screws. 2. If not already done, record the card’s MAC address for future reference (see “Installation Checklist” on page 3). 3. To prevent electrostatic discharge (ESD), place one hand on a metal surface. 4.
Getting Started Installing the Optional Environmental Monitoring Probe The EMP is available as an option. The EMP allows remote monitoring of the UPS’s environment through regular measurements of temperature and humidity through two external contacts. On UPSs with the EMP installed you can: l l l Set temperature and humidity thresholds. Configure the system to send notification of environmental alarms through e-mail messages and SNMP traps. Monitor current and historical environmental data.
Getting Started 2. Plug the other end of the serial cable into the serial COM port on the computer. 3. Connect an active Ethernet cable (not supplied) to the Ethernet port on the Network Card-MS (see Figure 5). Wait approximately two minutes until the UPS Data LED flashes regularly, indicating normal operation. Ethernet Port Settings/Sensor Port Ethernet Figure 5. Connecting the Card Eaton Network Card-MS User’s Guide P-164000100—Rev 1 www.eaton.
Getting Started Configuring the Card To configure the card: 1. Verify that the serial cable (supplied) is connected to the card’s Settings/Sensor port and the computer’s COM port. 2. Open your terminal emulation program (such as HyperTerminal). 3. Select the serial connection (such as COM1). 4. Set the serial line to 9600 baud, 8 data bits, no parity, 1 stop bit, no flow control (see Figure 6). Figure 6. Configuring Port Settings 5. Verify that the UPS is turned on.
Getting Started 6. Enter admin. The main menu displays (see Figure 8). ------------------------------------------------------------Eaton Network Card-MS ------------------------------------------------------------1 : Reset 2 : Network configuration 3 : Set Login Password to Default 4 : Return to Default Configuration 0 : Exit ------------------------------------------------------------Figure 8.
Getting Started 2. Type 1 and press Enter. The card displays the settings supplied by the server (see Figure 10). ------------------------------------------------------------Network configuration ------------------------------------------------------------MAC address : xx:xx:xx:FD:xC:xx Mode : Static IP IP address : xxx.xx.xxx.
Getting Started 2. Follow the instructions and enter the static IP parameters. Wait until Done displays, indicating that the IP parameters have been saved. 3. To exit, type 0 and press Enter. 4. Type 1 and press Enter, and then type 2 and press Enter to restart. The card restarts with the new IP settings in approximately one minute. NOTE The IPv6 parameters are read only through the serioal line configuration menu.
Chapter 3 Configuring the Card This chapter explains: l Navigating the card’s Web page l Understanding UPS properties l UPS power management l Understanding UPS measurements, Event log, and System log l Configuring e-mail notification l Configuring Simple Network Management Protocol (SNMP) options and managing from an SNMP network management system (NMS) l Setting up access control l Setting the date and time l Setting environmental thresholds NOTE You must be logged in as admin to confi
Configuring the Card Logging In By default, the user name and password are both admin (see Figure 14). Figure 14. Login Window Both the user name and password fields accept a maximum of ten characters. After five minutes have elapsed without activity on the Web page, or if the browser is closed and reopened, you must re-enter the user name and password. An error in either field results in rejection of the requested action (such as save, page access, or card reboot).
Configuring the Card To access Help: 1. Click Help. The Help page opens (see Figure 15). 2. Select a Help topic from the menu bar. The corresponding Help content displays on the right. Figure 15. Online Help Example Eaton Network Card-MS User’s Guide P-164000100—Rev 1 www.eaton.
Configuring the Card UPS Properties Essential information about the UPS status is available on the UPS Properties page (see Figure 16), which refreshes automatically every ten seconds. The UPS Properties page shows an image and generic name of the UPS. You can customize the default location Computer Room to name the location of your system (see “System Settings” on page 39). An animated diagram displays for online UPSs showing an overview of the current UPS operating mode.
Configuring the Card UPS Measurements Detail Place the cursor over an element in the diagram to display the UPS measurements detail (see Figure 17). These measurements are available for Normal mode, Battery mode, and Bypass mode. The available measurements depend on the UPS model. UPS Measurements Detail Figure 17. UPS Measurements Detail (AC Output Detail Shown) UPS Status Icons Table 3 lists the UPS status icons. Table 4 shows examples of the online UPS current operating modes. Table 3.
Configuring the Card Table 4. Operating Mode Diagrams Operating Mode Diagram UPS with Automatic Bypass UPS with Automatic and Manual Bypass UPS without Automatic Bypass NOTE If communication with the UPS is lost, all diagrams appear gray. Eaton Network Card-MS User’s Guide P-164000100—Rev 1 www.eaton.
Configuring the Card Table 5 lists all the elements that can appear in a UPS operating mode diagram. Table 5.
Configuring the Card Table 5.
Configuring the Card Table 5. Diagram Elements (Continued) Type Element AC Manual Bypass Flow Description Energy flow present Yellow No energy flow Gray AC Manual Bypass Status Open Green Closed Red AC Output Flow Energy flow present Yellow No energy flow Gray AC Output Load protected Green Load not protected Red Eaton Network Card-MS User’s Guide P-164000100—Rev 1 www.eaton.
Configuring the Card UPS Status List Select an item from the UPS Status list to view specific information about the UPS (see Figure 18). Table 6 lists the UPS status items available. The following sections describe each item in detail. UPS Status L:ist Figure 18. UPS Status List (Default UPS Status View Shown) Table 6.
Configuring the Card Table 7. UPS Output Status Element Description Receptacle powered Green Receptacle not powered or not protected Red l Battery load level: Remaining battery charge (in percent). The battery load level is further described by this additional information: - Charging: Indicates whether the utility power is present and the battery charge is in progress. - Discharging: Indicates whether the UPS is operating on battery. - Fault: Indicates whether the battery is faulty.
Configuring the Card Table 8. Security Levels Icon Level Critical Red Warning Yellow Unknown Gray Table 9.
Configuring the Card Table 9.
Configuring the Card Table 10.
Configuring the Card UPS Control Select UPS Control from the menu bar to open the UPS Control page (see Figure 21). NOTE The UPS Control page requires that you are logged in. If you are not logged in when you select UPS Control, the Login window opens (see “Logging In” on page 14). Figure 21. UPS Control Page The UPS Control page enables triggering of startup and shutdown sequences for the UPS main output and load segments.
Configuring the Card l l Delayed, safe power down & reboot: This is the same switch off and then on sequence as for the Safe power down & reboot command, but postponed by the number of seconds programmed in the Off Delay parameter. Delayed On: This is the same switch on sequence as for the Immediate On command, but postponed by the number of seconds programmed in the On Delay parameter. Selecting Save saves the Off Delay, Toggle Duration, and On Delay parameters on the card.
Configuring the Card Shutdown Parameters Select Shutdown Parameters from the menu bar to view and configure UPS operating parameters in battery mode and for power restoration (see Figure 23). Figure 23. Shutdown Parameters Page (Advanced Parameters Shown) Click Show advanced parameters to display additional parameters for adjusting specific thresholds related to the percentage of remaining battery charge level. The Output column allows you to name each receptacle (maximum 20 characters).
Configuring the Card UPS Shutdown (Master) l l l l l Shutdown if Remaining time under: Values are 0 to 99999 seconds (180 by default). This value is the minimum remaining backup time before the shutdown sequence is launched. Shutdown if Capacity is under: (Advanced parameter.) Values are 0 to 100%. The percentage cannot be less than that of the UPS and is the minimum remaining battery capacity level before the shutdown sequence launches. Shutdown after: (Advanced parameter.
Configuring the Card Measurements Select Measurements from the menu bar to view the measurements for a single-phase UPS (see Figure 24). Figure 24.
Configuring the Card Event Log Select Event Log from the menu bar to view logged events (see Figure 25). The card can save up to 435 events. When this threshold is exceeded, the system deletes the oldest event when a new one occurs. Save Log enables you to save values in CSV format. Clear Log enables you to delete all records. Enter the admin user name and password to validate this action. NOTE See Table 9 and Table 10 starting on page 24 for a list of managed alarms. Figure 25.
Configuring the Card Figure 26. System Log Page Notification E-Mail Notification The card can redirect UPS alarms to an e-mail server to distribute information to the appropriate recipients. The format of these e-mail messages is compatible with mobile telephone transfer systems using the short message service (SMS) standard for text messaging. NOTE A third-party application is required to convert e-mail messages to SMS. Eaton Network Card-MS User’s Guide P-164000100—Rev 1 www.eaton.
Configuring the Card Select Email Notification from the menu bar to configure e-mail recipients (see Figure 27). Figure 27. Email Notification Page (Shown with Environmental Monitoring Probe [EMP] option) On the Email Notification page, you can configure up to four recipients in the Recipient list to receive e-mail messages initiated by the card. Each recipient receives an e-mail message based on specific trigger events, selected from the right side of the page.
Configuring the Card l l Test: Enables you to send an e-mail message to the recipient immediately. Use this method to check e-mail transmission—particularly to check access to the SMTP server configured in the Network settings (see “Network Settings” on page 37). A transmission report is added to the system log. The event label in the subject and text of the message is replaced with a test label. If you make any modifications to the page, you must save them before using the Test function.
Configuring the Card l Message text: Allows a maximum of 255 characters. As shown in Figure 30, the body of the e-mail message contains: - Message text - The date and time of the event, as saved in the log - URL of the card, enabling a direct link with the card to be established - Attachments, as configured for the e-mail recipients - Duplication of the subject, if configured From: ups@domain.
Configuring the Card Network Settings Select Network from the menu bar to configure the network parameters of the card and authorize the remote upgrade of the embedded system (see Figure 30). xxx.xx.xxx.87 255.255.xxx.0 xxx.xx.xxx1 2001:xxx:xxx:xxxA:xxx:xxFF:FEFD:FFXX FEXX::XXX:XXFF:FEFD:FFXX 1789:xxx:xxx:xxxA:xxx:xxFF:FEFD:FFXX XXX.XXX.XXX.25 XXX.XXX.XXX.27 Figure 30. Network Settings Page Configurable network settings are: l IP Address: Indicates the IP address of the card.
Configuring the Card l l IPv6 Auto Config Enabled: Authorizes (choose ’Enabled’) the card to obtain configuration of IPv6 parameters from an IPv6 router. In this case, no IPv6 parameters are editable. IPv6 Address 1: - If Auto Config is enabled, this field displays the first IPv6 address built from the IPv6 router (not editable). - If Auto Config is not enabled, this field is editable and allows users to set a static IPv6 address.
Configuring the Card System Settings Select System from the menu bar to customize the information that displays on the UPS Properties page (see “UPS Properties” on page 16). The System Settings page opens (see Figure 31). Figure 31. System Settings Page Configurable system settings are: l l l l l l l l UPS Contact: Enables users to enter the name of the person responsible for UPS administration at IT network level and/or electrical maintenance. This text field is limited to 49 characters.
Configuring the Card Notified Applications Use the Notified Applications page to: l Display network management system (NMS) applications set to receive notifications from the card. All applications and their main parameters display. l Add an NMS to notified applications. l Test the operation of a notified application.
Configuring the Card l Configuration: Indicates the source of the Shutdown duration (sec) and Shutdown after (min) values: - Local (application). - Central (card). See “Central Shutdown Configuration” on page 42. l l Shutdown Duration: Indicates the time (in seconds) necessary to properly shutdown the computer. Shutdown after: Optional. Indicates the time available (in minutes) from the power failure until the launch of the UPS shutoff sequence.
Configuring the Card Figure 33 shows an example of the Network Management System page. Figure 33. Network Management System Page (Add NMS Shown) Central Shutdown Configuration Use the Central Shutdown Configuration page to define the shutdown and notification settings used by the Network Shutdown Modules that connect to the Network Card-MS. NOTE This feature is not supported by NetWatch. Eaton Network Card-MS User’s Guide P-164000100—Rev 1 www.eaton.
Configuring the Card To view and modify Central Shutdown Configuration parameters: 1. Select Notified Applications from the menu bar. The Notified Applications page opens. 2. Select the Configuration column head in the Notified Applications table to open the Central Shutdown Configuration page (see Figure 34). Figure 34. Central Shutdown Configuration Page 3. Change parameters as needed: - Shutdown after: Optional.
Configuring the Card Figure 35. Access Control Page Configurable access control settings are: l l Enter New Manager Login: The login user name. This text field (limited to ten characters) enables secure access and modification of pages. Default value is admin. Enter New Password: This text field (limited to ten characters) enables secure access to Configuration menu pages. Default value is admin. l Confirm New Password: Re-enter the new password.
Configuring the Card l l Telnet access: This parameter enables or disables access to the setting parameters interface using a Telnet/SSH/CLI connection. Telnet security: This parameter defines the protocol for access to the setting parameters interface. These two values are exclusive. l TELNET: The data are read or written using an unsecure access. l SSH: The data are read or written using a secure access. l Console interface: This parameter defines the method for accessing the setting parameters.
Configuring the Card l l l l l l SNMP Version: This field allows the user to select the SNMP protocol version: {Disabled, V1, V3 are supported by the card}. SNMP Community Read-Only: Provides the SNMPv1 Read community name that identifies a sub-group attached to a network manager or a logical entity. The card and the clients must share the same community name to communicate. SNMP Write Enabled: Enables the SNMP write function. SNMP Community Write: Displays only if SNMP Write is enabled.
Configuring the Card Date and Time You can set the card’s date and time manually or set it to synchronize with the NTP server from the Setting Time page (see Figure 37). Figure 37. Setting Time Page To set the date and time: 1. Click Time from the menu bar to open the Setting Time page. 2. To manually set the date and time, select Set manually and enter values in the Date and Time fields, and click Save. Maximum drift is ±2 min/month. 3.
Configuring the Card The time is updated every five hours to minimize any time drift. After two attempts, if the NTP server is not accessible, the card shifts to manual mode. The card uses the NTP protocol (UDP 123 port). The firewall must be set to transmit queries outside the intranet. If the timer server fails, an error message displays at the top of the page. 5. Click Save to connect with the server and set the date and time.
Configuring the Card Environment Status The Environment Status page displays the status of the optional EMP (see Figure 38). Figure 38. Environment Status Page Temperature and humidity measurements are displayed in a graduated bar (see Figure 39). Current Reading Low Threshold High Threshold Figure 39. Graduated Bar (Humidity Bar Shown) Status parameters: l l Cursor: Indicates the current reading.
Configuring the Card Environment Settings On the Environment Settings page, you can set the temperature and humidity thresholds that trigger a notification and a graceful shutdown of the protected systems (see Figure 40). NOTE If you are not already logged on, you will be prompted to enter your user name and password before accessing this page. The EMP measures temperature and humidity, and gives the status of the two contacts (used for door, alarms, or generator unit). Figure 40.
Configuring the Card l l l High threshold (humidity): If the humidity exceeds the set threshold, a notification is triggered if enabled. The default value is 90%. Low threshold (humidity): If the humidity falls below the set threshold, a notification is triggered if enabled. The default value is 5%. Hysteresis (humidity): Hysteresis must be set to prevent multiple notifications if humidity fluctuates around a threshold. The default value is 5%.
Chapter 4 Using the Telnet/SSH/CLI Interface This chapter describes how to use the Telnet/Secure Shell (SSH)/Command Line Interface (CLI) (Telnet/SSH/ CLI) interface to access the Network Card-MS. Overview Telnet is a terminal emulation protocol you can use to access and configure the parameters for the Network Card-MS. Telnet is not a secure protocol, but when used with SSH, the connection is secure.
Using the Telnet/SSH/CLI Interface Starting and Ending a Session To start a session: 1. Open a terminal emulator or other session manager such as PuTTY. 2. At the prompt, type telnet [IPaddress], where [IPaddress] is the IP address of the Network Card-MS. 3. If the connection is successful, the server responds with “Connected to [IPaddress],” and a welcome message. 4. At the Login and Password prompts, enter your user name and password.
Using the Telnet/SSH/CLI Interface Table 13 provides an overview of the menu tree for the MENU interface selection hierarchy. Table 13. MENU Selection Hierarchy Main Menu Item Submenu Secondary Submenu Description Reset — — Resets the card. Network settings MAC address, IP address, and other parameters — Configures the network parameters and authorizes remote upgrades SMTP menu Host name and other parameters Configures the SMTP server.
Using the Telnet/SSH/CLI Interface General Commands Use general commands to open, close, and control sessions (see Table 14). Table 14. General CLI Interface Commands help or ? Display help about a specific command. Syntax help [command] or [command] ? Example #> help getNetwork or #> getNetwork ? setEcho Hide, or not, all characters. If hidden, each character entered is replaced by an asterisk (*).
Using the Telnet/SSH/CLI Interface Table 15. Network Commands (Continued) setNetwork Modify a network setting. Syntax setNetwork [option1=xxxx] [option2=yyyy] . . . Options DHCP = 0 | 1(0=No, 1=Yes) IPAddress = “xxx.xxx.xxx.xxx “ (See Note 1) IPMask = “xxx.xxx.xxx.xxx“ (See Note 1) IPGateway = “xxx.xxx.xxx.xxx“ (See Note 1) HostName = “xx..xx” DomainName = “xx..
Using the Telnet/SSH/CLI Interface Table 15. Network Commands (Continued) setSNMP Modify an SNMP setting. Syntax getSNMP [option1] [option2] . . . Options snmpVersion = Disabled | V1 | V3 | V1V3 ReadCommunityName = “xx..xx“(See Note 1) WriteCommunitySecurityLevel = 0 | 2(0=No, 2=Yes) WriteCommunityName = “xx..xx“(See Notes 1, 2) User = “xx..xx“(See Note 1) UserSecurityLevel = 1 | 2 | 3(1=No Auth, 2=Auth NoPriv, 3=Auth Priv)(See Note 1) UserPassword = “xx..xx“(See Notes 1, 3, 5, 6) Admin = “xx..
Using the Telnet/SSH/CLI Interface System Commands Use system commands to customize the information about the UPS (see Table 17). Table 17. System Commands getSystem Syntax getSystem [option1] [option2] . . . Options Contact | Location | upsCustomName | Language Example #> getSystem Location setSystem Syntax setSystem [option1] [option2] . . . Options Contact = “xx..xx” Location = “xx..xx” upsCustomName = “xx..
Using the Telnet/SSH/CLI Interface Shutdown Commands Use shutdown commands to define UPS behavior during a shutdown (see Table 18). Table 18. Shutdown Commands getShutdown Syntax getShutdown N [option1] [option2] . . .
Using the Telnet/SSH/CLI Interface Access Control Commands Use access control commands to configure secure access to the card (see Table 19). Table 19. Access Control Commands getAccess Syntax getAccess [option1] [option2] . . . Options Login | Password | Security Example #> getAcess Login Comments For Password, each character is replaced with an asterisk (*). setAccess Syntax setAccess [option1] [option2] . . . Options Login = “xx..xx“ Password = “**..
Using the Telnet/SSH/CLI Interface Enviroment Commands Use environment commands to define settings for environmental sensors (see Table 21). Table 21. Environment Commands getEnv To read an environment setting Syntax getEnv [option1] Options Name Example #> getEnv Name setEnv To modify an environment setting Syntax setEnv [option1] Options Name = “xx..xx” Example #> setEnv Name=”sensor” getTemp To read a temperature setting Syntax getTemp [option1] [option2] ...
Using the Telnet/SSH/CLI Interface Table 21. Environment Commands (Continued) Example #> getHum Offset setHum To modify a humidity setting Syntax setHum [option1] [option2] ... Options HighThreshold = xx LowThreshold =xx Hysteresis = xx (0..5) Offset = xx (-5..
Chapter 5 MIB Objects This chapter describes the Management Information Base (MIB) files available with the card. A MIB is an information repository residing on a device in a communication network. Network management software uses a device’s MIB to manage the device. Every manageable device on a network has a MIB consisting of one or more files that list information about the device.
MIB Objects Table 22. PowerMIB Objects (Continued) MIB Object SNMP Format Add.path xupsOutputLoad Percent {4.1.0} xupsOutputFrequency 0.1 Hertz {4.2.0} Integer {4.3.0} — {4.4.0} xupsOutputNumPhases xupsOutputTable xupsOutputPhase Integer {4.4.1.1.x} xupsOutputVoltage RMS Volts {4.4.1.2.x} xupsOutputCurrent RMS Amps {4.4.1.3.x} xupsOutputWatts Watts {4.4.1.4.x} xupsOutputSource xupsBypassFrequency xupsBypassNumPhases xupsBypassTable xupsBypassPhase Integer {4.5.0} 0.1 Hertz {5.
MIB Objects Table 22. PowerMIB Objects (Continued) MIB Object SNMP Format Add.path xupsOnBypass — {7.11.0} xupsBypassNotAvailable — {7.12.0} xupsOutputOff — {7.13.0} xupsInputFailure — {7.14.0} xupsBuildingAlarm — {7.15.0} xupsShutdownImminent — {7.16.0} xupsOnInverter — {7.17.0} xupsBreakerOpen — {7.20.0} xupsAlarmBatteryBad — {7.23.0} xupsOutputOffAsRequested — {7.24.0} xupsDiagnosticTestFailed — {7.25.0} xupsCommunicationsLost — {7.26.
MIB Objects Table 22. PowerMIB Objects (Continued) MIB Object SNMP Format Add.path xupsTopoMachineCode Integer {13.2.0} xupsTopoUnitNumber Integer {13.3.0} xupsTopoPowerStrategy Integer {13.4.
MIB Objects Table 23. Eaton Pulsar MIB (MGE MIB) Objects (Continued) MIB Object SNMP Format Add.
MIB Objects Table 24. Pulsar MIB (MGE MIB) Objects (EMPs) (Continued) MIB Object SNMP Format upsmgEnvironmentTemperature Add.path 0.1° C {8,7,1,3,1} upsmgEnvironmentTemperatureLow 1 (yes), 2 (no) {8,7,1,4,1} upsmgEnvironmentTemperatureHigh 1 (yes), 2 (no) {8,7,1,5,1} 0.
MIB Objects Table 25. MIB Traps (Continued) MIB Trap Trap Trap Severity Level upsmgOffToStart 29 2 upsmgOffInProgress 31 3 upsmgCommunicationFailure 37 3 upsmgCommunicationRestored 38 1 upsmgRedundancyLost 65 2 upsmgRedundancyOK 66 2 upsmgProtectionLost 67 2 upsmgProtectionOK 68 2 Table 26.
Chapter 6 Operation and Maintenance This chapter explains: l Serial cable pinout l Detailed serial configuration menus l Firmware upgrade instructions Serial Cable Pinout Figure 42 shows the serial cable and pinout. Male RJ-45 Connector Female DB-9 Connector 2 3 5 Frame Shielded Cable Female DB-9 Connector 3 6 4 Frame Male RJ-45 Connector Figure 42. DB-9-to-RJ-45 Serial Cable and Pinout Serial Configuration Menus Use the supplied cable to connect the card to a computer. 1.
Operation and Maintenance ------------------------------------------------------------Reset ------------------------------------------------------------1 : Hardware Reset 2 : Restart application 0 : Exit ------------------------------------------------------------Figure 44.
Operation and Maintenance l Modify Network settings: To modify existing network parameters (see Figure 47). Restart the card to activate the new parameters. In DHCP mode, the card can receive the following parameters according to the DHCP server settings: - IP address - Subnet mask - Gateway address - Primary DNS server - Secondary DNS server For each of the following questions, you can press to select the value shown in braces, or you can enter a new value.
Operation and Maintenance Option 4: Return to Default Configuration Select menu item 4 to restore the parameters to the factory-default configuration (see “Card Defaults” on page 5). Wait for the confirmation message (see Figure 50). Restart the card to save the default parameters. Configuration has been set to default one. You must Reset the card. Figure 50. Default Configuration Confirmation Message Upgrading the Firmware You can update the card’s firmware by downloading the appropriate file.
Chapter 7 Shutdown This chapter explains: l Protection applications l Shutdown criteria managed by the card l Load Segments l Shutdown sequences Protection Applications NetWatch and NSM protection applications send the following essential data to the card: l l IP Address or hostname of the server on which it is installed so that the card can inform the application of power events.
Shutdown Table 27. Shutdown Criteria Criteria Description Backup Time before Initiating the Shutdown Procedure (Shutdown After – Shutdown Timer) When the UPS switches to battery power, the card starts the Shutdown Timer countdown and launches the system shutdown procedure at the end of the countdown. Select this value carefully so that users have time to complete their tasks and disconnect without exceeding battery backup time.
Shutdown Load Segments Some UPSs are equipped with load segments, which are always dependent on the UPS’s master. Shutdown of the master initiates a shutdown of the load segments (usually two load segments). Refer to the UPS user’s guide for the location of the load segments. Figure 53 shows a graph of the shutdown sequence for the load segments.
Shutdown Sequential Startup You can delay receptacle power-on to reduce inrush currents on startup or to sequence the startup of several devices. Load segment startup after a given time is based on startup of the main receptacle. Extended Power Outage, Shutdown Initiated by the Shutdown Timer (Shutdown After) During battery backup time, the Shutdown Timer of the Network Card-MS is reached.
Shutdown Figure 55 shows a graph of a shutdown initiated by the “Low battery power” message. Utility Failure Start Shutdown Output 1 Start Shutdown Main Output Utility Restore Utility Shutdown Duration Main Output Battery Capacity Under NetWatch/NSM 1 on Main Output Shutdown Duration Output 1 Output 1 Battery Capacity Under (Output 1) NetWatch/NSM 2 on Output 1 Figure 55.
Shutdown Shutdown Management With Two Network Card-MS Cards Some UPSs can have two Network Card-MS cards to: l Increase the number of protected servers l Protect two groups of servers connected to separate networks Shutdown Duration The protection application transmits its own shutdown duration to the Network Card-MS (as described in Table 27). Based on these values (maximum shutdown duration of all subscribed customer systems), the card sends the delayed shutdown order to the UPS.
Chapter 8 Specifications This chapter lists the technical specifications in Table 28. Table 28.
Chapter 9 Service and Support If you have any questions or problems with the Network Card-MS, call your Local Distributor or the Help Desk at one of the following telephone numbers and ask for a Network Card-MS technical representative.
Service and Support Two-Year Limited Warranty (US and Canada) Network Card-MS WARRANTOR: The warrantor for the limited warranties set forth herein is Eaton Corporation, a Delaware Corporation company (“Company”). LIMITED WARRANTY: This limited warranty (this “Warranty”) applies only to the original End-User (the “End-User”) of the Network Card-MS (the “Product”) purchased on or after June 1, 2004 and cannot be transferred.
Service and Support Company shall not be responsible for any charges for testing, checking, removal or installation of Warranted Items. COMPANY DOES NOT WARRANT EQUIPMENT NOT MANUFACTURED BY COMPANY. IF PERMITTED BY THE APPLICABLE MANUFACTURER, COMPANY SHALL PASS THROUGH SUCH MANUFACTURER’S WARRANTIES TO END-USER. COMPANY DOES NOT WARRANT SOFTWARE (IF APPLICABLE TO THE PRODUCT), INCLUDING SOFTWARE EMBEDDED IN PRODUCTS, THAT IS NOT CREATED BY COMPANY.
