Technical data
June 2008
40-42
For more information visit: www.eaton.com CA08102001E
Adjustable Frequency Drives
40
SLX9000
Enclosed Drives
Johnson Controls Metasys™ N2 Network Communications
The OPTC2 fieldbus board provides communication
between the SLX9000 drive and a Johnson Controls
Metasys™ N2 network. With this connection, the drive
can be controlled, monitored and programmed from the
Metasys system. The N2 fieldbus is available as a factory
installed option and as a field installable kit.
Modbus RTU Network Communications
The Modbus Network Card OPTC2 is used for connecting the
9000X Drive as a slave on a Modbus network. The interface
is connected by a 9-pin DSUB connector (female) and the
baud rate ranges from 300 to 19200 baud. Other communi-
cation parameters include an address range from 1 to 247; a
parity of None, Odd or Even; and the stop bit is 1.
Modbus/TCP Network Communications
The Modbus/TCP Network Card OPTCI is used for connect-
ing the 9000X Drive to Ethernet networks utilizing Modbus
protocol. It includes an RJ-45 pluggable connector. This
interface provides a selection of standard and custom
register values to communicate drive parameters. The board
supports 10 Mbps and 100 Mbps communication speeds.
The IP address of the board is configurable over Ethernet
using a supplied software tool.
BACnet Network Communications
The BACnet Network Card OPTCJ is used for connecting the
9000X Drive to BACnet networks. It includes a 5.08 mm plug-
gable connector. Data transfer is Master-Slave/Token Pass-
ing (MS/TP) RS-485. This interface uses a collection of 30
Binary Value Objects (BVOs) and 35 Analog Value Objects
(AVOs) to communicate drive parameters. The card supports
9.6, 19.2 and 38.4 Kbaud communication speeds and sup-
ports network addresses 1 – 127.
Profibus Network Communications
The Profibus Network Card OPTC3 is used for connecting the
SLX9000 as a slave on a Profibus-DP network. The interface
is connected by a 9-pin DSUB connector (female). The baud
rates range from 9.6K baud to 12M baud, and the addresses
range from 1 to 127.
LonWorks Network Communications
The LonWorks Network Card OPTC4 is used for connecting
the SLX9000 on a LonWorks network. This interface uses
Standard Network Variable Types (SNVT) as data types.
The channel connection is achieved using a FTT-10A Free
Topology transceiver via a single twisted transfer cable. The
communication speed with LonWorks is 78 kBits/s.
CanOpen (Slave) Communications
The CanOpen (Slave) Network Card OPTC6 is used for
connecting the SLX9000 to a host system. According to
ISO11898 standard cables to be chosen for CAN bus should
have a nominal impedance of 120Ω, and specific line delay
of nominal 5 nS/m. 120Ω line termination resistors required
for installation.
DeviceNet Network Communications
The DeviceNet Network Card OPTC7 is used for connecting
the SLX9000 on a DeviceNet Network. It includes a 5.08 mm
pluggable connector. Transfer method is via CAN using a
2-wire twisted shielded cable with 2-wire bus power cable
and drain. The baud rates used for communication include
125K baud, 250k baud and 500K baud.
Product Selection
When Ordering
■
Select a Base Catalog Number that meets the application
requirements — nominal horsepower, voltage and enclosure
rating (the enclosed drive’s continuous output amp rating
should be equal to or greater than the motor’s full load amp
rating). The base enclosed package includes a standard drive,
door mounted Local/Remote Keypad and enclosure.
■ If Control/Communication option is desired, change the
appropriate code in the Base Catalog Number.
■ Select Enclosed Options. Add the codes as suffixes to the
Base Catalog Number in alphabetical and numeric order.
■ Read all Footnotes.
480V Drives
Table 40-58. 480V AC Input Base Drive
Enclosure dimensions listed on Pages 40-44 – 40-48.
Includes drive, keypad and enclosure.
Enclosure
Size
hp Current
(A)
NEMA Type 1 NEMA Type 12 NEMA Type 3R
Frame
Size
Base Catalog
Number
Price
U.S. $
Frame
Size
Base Catalog
Number
Price
U.S. $
Frame
Size
Base Catalog
Number
Price
U.S. $
High Overload Drive and Enclosure
MF0 1
1-1/2
2
3
5
2.2
3.3
4.3
5.6
7.6
MF4
MF4
MF4
MF4
MF4
SLX00114EA
SLXF1514EA
SLX00214EA
SLX00314EA
SLX00514EA
MF4
MF4
MF4
MF4
MF4
SLX00124EA
SLXF1524EA
SLX00224EA
SLX00324EA
SLX00524EA
MF4
MF4
MF4
MF4
MF4
SLX00134EA
SLXF1534EA
SLX00234EA
SLX00334EA
SLX00534EA
MF1 7-1/2
10
15
12
16
23
MF5
MF5
MF5
SLX00714EA
SLX01014EA
SLX01514EA
MF5
MF5
MF5
SLX00724EA
SLX01024EA
SLX01524EA
MF5
MF5
MF5
SLX00734EA
SLX01034EA
SLX01534EA
MF2 20
25
30
31
38
46
MF6
MF6
MF6
SLX02014EA
SLX02514EA
SLX03014EA
MF6
MF6
MF6
SLX02024EA
SLX02524EA
SLX03024EA
MF6
MF6
MF6
SLX02034EA
SLX02534EA
SLX03034EA
Low Overload Drive and Enclosure
MF0 1-1/2
2
3
5
7-1/2
3.3
4.3
5.6
7.6
12
MF4
MF4
MF4
MF4
MF4
SLXF1514BA
SLX00214BA
SLX00314BA
SLX00514BA
SLX00714BA
MF4
MF4
MF4
MF4
MF4
SLXF1524BA
SLX00224BA
SLX00324BA
SLX00524BA
SLX00724BA
MF4
MF4
MF4
MF4
MF4
SLXF1534BA
SLX00234BA
SLX00334BA
SLX00534BA
SLX00734BA
MF1 10
15
20
16
23
31
MF5
MF5
MF5
SLX01014BA
SLX01514BA
SLX02014BA
MF5
MF5
MF5
SLX01024BA
SLX01524BA
SLX02024BA
MF5
MF5
MF5
SLX01034BA
SLX01534BA
SLX02034BA
MF2 25
30
40
38
46
61
MF6
MF6
MF6
SLX02514BA
SLX03014BA
SLX04014BA
MF6
MF6
MF6
SLX02524BA
SLX03024BA
SLX04024BA
MF6
MF6
MF6
SLX02534BA
SLX03034BA
SLX04034BA
Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . SS-3