Installation Manual

P50938 Rev 09
Effective: September 2010 Page 2
SPECIFICATIONS
2-Wire AC Sensors 3-Wire DC Sensors
Input Voltage 20-132 VAC 6-48 VDC
Load Current 5-500 mA, 5-250 mA > 50° C
For all E59-M12... 5-300 mA, 200 mA > 50° C
< 500 mA @ 6-30 VDC
< 300 mA @ 32-48 VDC
Voltage Drop < 10 VAC < 2.5 VDC
Burden Current N/A < 15 mA
Protection Overcurrent
1
Auto Reset
Switching Hysteresis < 15% Rated Sensing Distance
Repeat Accuracy Shielded Models: < 1% Rated Sensing Distance
Unshielded Models: < 3% Rated Sensing Distance
Surge Capacity 3 A / 30 ms
Temperature Range -40° to +158° F (-40° to +70° C)
Material of Construction Housing: 303 Stainless Steel; End Bells: Polycarbonate; Face Caps: Ryton®; Cable: AWM Style 20387 (PVC)
Vibration 10-55 Hz, 1 mm Amplitude, IEC 60068-2-6
Shock 30 g, 11 mS, IEC 68-2-27
Indicator LED 360° Viewable
Enclosure Ratings NEMA 4, 4X, 6, 6P, 12 and 13 (IP68)
2
Response
Time
3
Factory Default Mode 30 Hz (10 V/m) Shielded (10 V/m)
12 mm: 580 Hz; 18 mm: 390 Hz; 30 mm: 240 Hz
Unshielded (10 V/m)
12 mm: 300 Hz; 18 mm: 150 Hz; 30 mm: 90 Hz
Side by Side Mode
4
30 Hz (10 V/m) 50 Hz (20 V/m)
High Noise Immunity Mode 10 Hz (> 20 V/m) 10 Hz (> 20 V/m)
1
Overcurrent protection for conductor size 20 AWG is 5 A; 22 AWG is 3 A; 24 AWG is 2 A.
2
Our products conform to NEMA tests as indicated, however, some severe washdown applications can exceed these NEMA test specifi cations. For questions about a specifi c application, contact our
Applications Department at [phone].
3
The iProx sensor may be programmed to perform in “Side by Side” and high noise applications by using the ProxView Software (E59SW1) and a programming accessory (E59RP1).
For more information on these programming accessories, contact Eaton’s Sensor Applications Department at [phone].
4
When mounting multiple iProx sensors in an area less than seven times its sensing range, it is recommended to set the noise immunity setting of the sensor to “Side by Side” mode. Refer to the ProxView
Software User Guide (P50228) for details.
APPROXIMATE DIMENSIONS (IN/MM)
Cable Models
Size Cap A B C D
12 mm Shielded 2.86 (72.6) 1.98 (50.3) 0.02 (0.50) 0.67 (17)
Unshielded 2.86 (72.6) 1.64 (41.6) 0.36 (9) 0.67 (17)
18 mm Shielded 2.54 (64.5) 2.00 (50.9) 0.02 (0.50) 0.94 (24)
Unshielded 2.54 (64.5) 1.47 (37.4) 0.55 (14) 0.94 (24)
30 mm Shielded 2.74 (69.6) 2.13 (54.1) 0.03 (0.75) 1.41 (36)
Unshielded 2.74 (69.6) 1.41 (35.8) 0.75 (19) 1.41 (36)
Micro Connector Models
Size Cap A B C D
12 mm Shielded 3.05 (77.5) 1.98 (50.3) 0.02 (0.50) 0.67 (17)
Unshielded 3.05 (77.5) 1.64 (41.6) 0.36 (9) 0.67 (17)
18 mm Shielded 2.73 (69.3) 2.00 (50.9) 0.02 (0.50) 0.94 (24)
Unshielded 2.73 (69.3) 1.47 (37.4) 0.55 (14) 0.94 (24)
30 mm Shielded 2.92 (74.1) 2.13 (54.1) 0.03 (0.75) 1.41 (36)
Unshielded 2.92 (74.1) 1.41 (35.8) 0.75 (19) 1.41 (36)
Note: Metal nuts are provided for equipment grounding means.
WIRING DIAGRAMS (NORMALLY OPEN AND NORMALLY CLOSED)
AC Cable AC Micro AC Mini
DC Cable (NPN) DC Cable (PNP) DC Micro (NPN) DC Micro (PNP)
DC Micro Dual NPN Output DC Micro Dual PNP Output
DC Cable Dual NPN Output DC Cable Dual PNP Output
B DC
A
B DC
A
L1
L2
Load
BU
BN
(-)
+V
BK
Load
BU
BN
(-)
+
V
BK
Load
(-)
+V
Load
Load
(-)
+V
Load
Load
(-)
+V
Load
Load
(-)
+V
Load
Load
BU
BN
(-)
+V
BK
Load
WH
Load
BU
BN
(-)
+V
BK
Load
WH
Load
Questions? Call our Sensor Application Engineers at [phone].