Firmware Manual

Chapter 8—Multi-Purpose Application
PowerXL DG1 Series Adjustable Frequency Drives MN040004EN—March 2014 www.eaton.com 117
Notes
1
Parameter value can only be changed after the drive has stopped.
2
Parameter value will be set to be default when changing macros.
P8.35
2
Acc Compensation Time
Constant
0.0 1000.0 % 0.0 1611
P8.36
2
Acc Compensation Filter
Time Constant
0 3000 ms 0 1612
P8.37
2
Flux Reference 0.0 500.0 % 100.0 1620
P8.38
2
Stop State Magnetization 0.0 100.0 % 100.0 1621
P8.39
2
Start Boost Rise Time –1 32000 s 0 1622
P8.40
2
Flux Current Ramp Time 0 32000 ms 200 1623
P8.41
2
Zero Speed Start Time 0 32000 ms 100 1624
P8.42
2
Zero Speed Stop Time 0 32000 ms 100 1625
P8.43
2
Droop Control Filter Time
Constant
0 3000 ms 0 1630
P8.44
2
Startup Torque Selection 0 1631 0 = Not Used
1 = TorqueMemory
2 = TorqueReference
3 = StartupTorqueFWD/REV
P8.45
2
Torque Memory Start –300.0 300.0 % 0.0 1632
P8.46
2
Startup Torque Forward –300.0 300.0 % 0.0 1633
P8.47
2
Startup Torque Reverse –300.0 300.0 % 0.0 1634
P8.48 Startup Torque Actual % 1635
P8.49
2
Startup Torque Time 0 10000 ms 50 1667
P8.50
1
Stator Resistor 0.001 65.535 ohm 0.033 771
P8.51
1
Rotor Resistor 0.001 65.535 ohm 0.034 772
P8.52
1
Leak Inductance 0.001 65.535 mh 0.128 773
P8.53
1
Mutual Inductance 0.01 655.35 mh 3.44 774
P8.54
1
Excitation Current 0.1 Drive Nom
CT*2
A 0.1 775
Table 101. Protections—P9
Code Parameter Min. Max. Unit Default ID Note
P9.1
12
4 mA Input Fault 0 306 0 = No Action
1 = Warning
2 = Warning: Previous Freq
3 = Warning: Preset Freq
4 = Fault
5 = Fault, Coast
P9.2
12
4 mA Fault Frequency 0.00 Par. P1.2 Hz 0.00 331
P9.3
12
External Fault 2 307 See P9.11
P9.4
12
Input Phase Fault 2 332 See P9.11
P9.5
12
Uvolt Fault Response 2 330 See P9.11
P9.6
12
Output Phase Fault 2 308 See P9.11
P9.7
12
Ground Fault 2 309 See P9.11
P9.8
12
Motor Thermal Protection 2 310 See P9.11
P9.9
2
Motor Thermal F0 Current 0.0 150.0 % 40.0 311
P9.10
2
Motor Thermal Time 1 200 min 12 312
Table 100. Motor Control—P8, continued
Code Parameter Min. Max. Unit Default ID Note