Firmware Manual

ManualsBrandsEaton ManualsControl & Automation7.5Hp, 10Hp PowerXL DG-1, VFD, N1

Appendix A—Description of Parameters

PowerXL DG1 Series Adjustable Frequency Drives MN040004EN—March 2014 www.eaton.com 147

P5.4 538 RO3 Function, continued 1, 2, 3, 4 RW

Code Modbus ID Parameter Application

RO/RW

Setting Value Signal Content Standard

Multi-

Pump

and Fan

Multi-

PID

Multi-

Purpose

0 = Not used

1 = Ready

2 = Run

3 = Fault

4 = Fault inverted

5 = Warning

Out of operation

Frequency converter is ready for operation

Frequency converter is operating (motor is running)

A fault trip has occurred

A fault trip has not occurred

Always if a warning exists

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

6 = Reverse

7 = At speed

8 = Zero frequency

9 = Frequency Limit1 supervision

10 = Frequency Limit2 supervision

The reverse command has been selected

The output frequency has reached the set

reference

Motor output is at zero frequency

Supervision for frequency limit1

Supervision for frequency limit2

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

11 = PID1 supervision

12 = PID2 supervision

13 = Over heat warning

14 = Over current regulator

15 = Over volt regulator

Supervision for PID1 controller

Supervision for PID2 controller

Drive over heat has occurred

Over current regular is enabled

Over volt regular is enabled

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

16 = Under volt regulator

17 = 4 mA fault

18 = External brake

19 = External brake inverter

20 = Torque limit supervision

Under volt regular is enabled

4 mA fault has occurred

External brake is working

External brake isn’t working

Supervision for torque limit

■

■

—

—

■

■

■

—

—

■

■

■

—

—

■

■

■

■

■

■

21 = Reference limit supervision

22 = Control from IO

23 = Unrequired rotation direction

24 = Thermal fault

25 = Fire mode

Supervision for reference limit

I/O is the control place

The active direction isn’t the same with the

reference direction

Thermal fault has occurred

Drive is in fire mode

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

26 = Bypass running

27 = External fault

28 = Remote control

29 = Jog speed

30 = Motor thermal protection

Drive is in bypass mode

External fault has occurred

Remote is the control place

Drive is in jog mode

Motor is thermal protected

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

31 = Fieldbus input1

32 = Fieldbus input2

33 = Fieldbus input3

34 = Fieldbus input4

35 = Damper control

—

—

—

—

Drive is in damper control

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

36 = Timer1 status

37 = Timer2 status

38 = Timer3 status

39 = Emergency stop

40 = Power limit supervision

The status of timer1

The status of timer2

The status of timer3

Emergency stop has occurred

Supervision for power limit

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

41 = Temperature limit supervision

42 = Analog input supervision

43 = Motor1 control

44 = Motor2 control

45 = Motor3 control

Supervision for temperature limit

Supervision for analog input

Motor1 is controlled

Motor2 is controlled

Motor3 is controlled

■

■

—

—

—

■

■

■

■

■

■

■

■

■

■

■

■

■

■

■

46 = Motor4 control

47 = Motor5 control

48 = Logic fulfilled

49 = PID1 sleep

50 = PID2 sleep

Motor4 is controlled

Motor5 is controlled

The status of logic function

PID1 controller is in sleep mode

PID2 controller is in sleep mode

—

—

—

—

—

■

■

—

■

—

■

■

—

■

■

■

■

■

■

■