Installation Guide

Type 3 Surge Protection Device
SurgeBloc™
Duplex Receptacle Surge Protective Device with Noise Filter with or without Isolated Ground
General Information
1. To be installed or checked by an electrician or qualified person only.
2. All wiring devices must be installed and used in accordance with applicable listings, ratings, and codes.
3. Use only copper wire with this device. Do not use with aluminum wire.
4. (For Isolated Ground Devices (IG) only): An orange triangle on the face of a device or an orange face with a black triangle
identifies the device as Isolated Ground with dual grounding system.
5. Failure to wire as instructed may cause damage to device or equipment, or personal injury.
Specifications
All Models: Wire Leads: No. 12 AWG
1
208, IG1208 15A - 125V, 1875W
1210, IG1210 20A - 125V, 2500W
UL Voltage Protection Rating (V pk)
Line - Neutral 600V
Line - Ground 600V
Neutral - Ground 1000V
AS DETERMINED BY USING AN IMPULSE WAVEFORM
OF 6 KV (1.2 x 50 μs), 3 KA (8.0 x 20 μs)
ENERGY RATING (10,1000 μs)
Line – Neutral 170 JOULES
Line – Ground 170 JOULES
Neutral – Ground 340 JOULES
PEAK SURGE CURRENT (8 x 20 μs)
Line – Neutral 12,000 AMPS
Line – Ground 12,000 AMPS
Neutral – Ground 12,000 AMPS
Instructions:
1. Turn circuit breaker OFF or remove fuse(s) and test that the power is off.
2. (For Non-Isolated Ground): Connect the green grounding wire from the receptacle to the incoming green ground wire with a
wire connector.
(For Isolated Ground): Connect the green grounding wire from the receptacle to the incoming green isolated equipment ground
wire with a wire connector. In a metallic system with grounded steel box, the E-Z Ground™ feature of the Cooper SurgeBloc™
receptacle will automatically ground a metal wall plate. To preserve grounding isolation, care should be taken that the green
isolated equipment ground wire is not connected the building system ground.
3. Black and white line wires should be connected the the black and white leads on the receptacle with wire connectors.
4. Fasten the receptacle to the box with the captive screws provided, being sure the mounting yoke is flush to the wall.
Operation:
The Cooper Wiring Devices (CWD) SurgeBloc™, a Type 3 Surge Protective Device (SPD) protects connected loads from
potentially damaging voltage spikes (surges) caused by lightning strikes near line, or the switching of inductive loads on the line
(motor loads), as well as from RFI (radio frequency interference). It cannot survive, or provide protection, in the rare event of a
direct lightning strike on the service power line. The CWD SurgeBloc™ alerts you to the failure of the surge protection
component by means of an audible signal. If alarm “sounds”, device has “received” power surges in excess of its capacity, and
is no longer functioning as a surge protector. To shut off the alarm, simply unplug the module and replace with a new module to
restore surge protection. Replace with 1209 module which can be obtained from your electrical distributor or by contacting
Cooper Wiring Devices at 866-853-4293.
Note: When alarm sounds and the module is removed, the receptacle still functions as a normal duplex receptacle without surge
protection.
Parasurtenseur de Type 3
SurgeBloc™
Prise double avec Parasurtenseur avec filtrage de parasites, isolée ou non par rapport à la terre
Informations générales
1. Cet appareil doit être installé ou contrôlé uniquement par un électricien ou une personne qualifiée.
2. Il faut installer et utiliser tous les articles de câblage selon les normes et homologations en vigueur et dans la limite de leurs
valeurs nominales.
3. Utilisez exclusivement des fils de cuivre sur cet appareil. N’utilisez pas de fils d’aluminium.
4. (Pour les appareils isolés par rapport à la terre uniquement (IG)) : Un triangle orange sur la face avant d’un appareil ou une
face avant orange avec un triangle noir signifie que l’appareil est isolé par rapport à la terre et qu’il est doté d’un double système
de mise à la terre.
5. Si vous ne câblez pas comme indiqué, il y a risque d’abîmer cet appareil, d’endommager l’équipement qui y est raccordé ou de
causer des blessures.
Spécifications
Tous les modèles : calibre n° 12 AWG
1208, IG1208 15 A - 125 V, 1875 W
1210, IG1210 20 A - 125 V, 2500 W
Tension de protection nominale selon UL (V crête)
Phase – Neutre 600 VOLTS
Phase – Terre 600 VOLTS
Neutre – Terre 1000 VOLTS
COMME DÉTERMINÉ EN EMPLOYANT UNE IMPULSION EN FORME D’ONDE
DE 6 KV (1,2 x 50 μs), 3 KA (8,0 x 20 μs)
ÉNERGIE NOMINALE (10/1000 μs)
Phase – Neutre 170 JOULES
Phase – Terre 170 JOULES
Neutre – Ground 340 JOULES
SURINTENSITÉ TRANSITOIRE DE CRÊTE (8 X 20 μs)
Phase – Neutral 12,000 A
Phase – Terre 12,000 A
Neutre – Terre 12,000 A
Instructions
1. Coupez le courant au disjoncteur ou enlevez le ou les fusibles puis contrôlez que le courant est coupé.
2. (Non isolée par rapport à la terre) : Raccordez le fil de terre vert de la prise sur le fil de terre vert de l’arrivée à l’aide d’un
capuchon de connexion.
(Isolé par rapport à la terre) : Raccordez le fil de terre vert de la prise sur le fil de terre vert de l'arrivée de l’équipement isolé à
l’aide d’un capuchon de connexion. Dans un système métallique avec une boîte de raccordement en acier raccordée à la terre,
la fonction de terre E-Z Ground™ de la prise avec parasurtenseur SurgeBloc™ de Cooper raccorde automatiquement la plaque
murale à la terre. Pour préserver l’isolation par rapport à la terre il faut faire bien attention de ne pas raccorder le fil de terre
vert de l’équipement isolé au circuit de terre du bâtiment.
3. Les fils de phase noir et blanc doivent être raccordés aux conducteurs noir et blanc de la prise à l’aide de capuchons de
connexion.
439RB-PTA (REV. B)
ENGLISH IN U.S.A.: Cooper Wiring Devices, 203 Cooper Circle, Peachtree City, GA 30269 • 866-853-4293
FRANÇAIS
IN CANADA: Cooper Wiring Devices, 5925 McLaughlin Road, Mississauga, Ontario L5R 1B8 • 800-267-1042