Data Sheet

ManualsBrandsEaton ManualsAutomationDILM250-S/22(220-240V50/60HZ) Electrical contactor 3 makers 132 kW 1 pc(s)

DATASHEET - DILM250-S/22(220-240V50/60HZ)

Contactor, 380 V 400 V 132 kW, 2 N/O, 2 NC, 220 - 240 V 50/60 Hz, AC

operation, Screw connection

Part no. DILM250-S/22(220-240V50/60HZ)

Catalog No. 274190

Alternate Catalog

No.

XTCS250L22B

EL-Nummer

(Norway)

4110261

Delivery program

Product range   Contactors

Application   Contactors for Motors

Subrange   Standard devices greater than 170 A

Utilization category   AC-1: Non-inductive or slightly inductive loads, resistance furnaces

NAC-3: Normal AC induction motors: starting, switch oﬀ during running

AC-4: Normal AC induction motors: starting, plugging, reversing, inching

Connection technique   Screw connection

Rated operational current

  

AC-3   

380 V 400 V I

A 250

AC-1   

Conventional free air thermal current, 3 pole, 50 - 60 Hz   

Open   

at 40 °C I

A 430

enclosed I

A 300

Conventional free air thermal current, 1 pole   

open I

A 875

enclosed I

A 750

Max. rating for three-phase motors, 50 - 60 Hz

  

AC-3   

220 V 230 V P kW 75

380 V 400 V P kW 132

660 V 690 V P kW 170

1000 V P kW 108

AC-4   

220 V 230 V P kW 62

380 V 400 V P kW 110

660 V 690 V P kW 137

1000 V P kW 108

Contact sequence  

Can be combined with auxiliary contact   DILM820-XHI…

Actuating voltage   220 - 240 V 50/60 Hz

Voltage AC/DC   AC operation

Contacts

  

N/O = Normally open   2 N/O

N/C = Normally closed   2 NC

Auxiliary contacts

  

possible variants at auxiliary contact module ﬁtting options   on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA

Side mounting auxiliary contacts  

Instructions   Interlocked opposing contacts according to IEC/EN 60947-5-1 Appendix L, inside

the auxiliary contact module

06/18/2021 Eaton 274190 ED2021 V80.0 EN 1 / 12

Summary of content (12 pages)

PAGE 1
DATASHEET - DILM250-S/22(220-240V50/60HZ) Contactor, 380 V 400 V 132 kW, 2 N/O, 2 NC, 220 - 240 V 50/60 Hz, AC operation, Screw connection Delivery program Part no. Catalog No. Alternate Catalog No.
PAGE 2
Auxiliary contacts used as mirror contacts according to IEC/EN 60947-4-1 Appendix F (not N/C late open) Instructions integrated suppressor circuit in actuating electronics 660 V, 690 V or 1000 V: not directly reversing Notes DILM…-S power contactors are actuated traditionally ① Stopping in the event of an emergency (emergency switching oﬀ) Technical data General Standards IEC/EN 60947, VDE 0660, UL, CSA Lifespan, mechanical AC operated Operations x 10 6 10 Operating frequency, mechanical AC oper
PAGE 3
Flexible with ferrule mm 1 x (0.75 - 2.5) 2 x (0.75 - 2.5) Solid or stranded AWG 18 - 14 2 Control circuit cable connection screw/bolt M3.5 Tightening torque Nm 1.
PAGE 4
Open, 3-pole: 50 – 60 Hz Notes At maximum permissible ambient temperature (open.
PAGE 5
Impedance per pole mΩ Magnet systems 0.15 Voltage tolerance US 220 - 240 V 50/60 Hz AC operated Pick-up 0.85 x US min - 1.1 x US max AC operated Drop-out 0.2 x US min - 0.4 x US max Power consumption of the coil in a cold state and 1.0 x US Note on power consumption Control transformer with uk ≦ 10% Pull-in power Pick-up VA 360 Pull-in power Pick-up W 325 Sealing power Sealing VA 7.3 Sealing power Sealing W 4.
PAGE 6
DC A Short Circuit Current Rating 1 SCCR Basic Rating SCCR kA 18 max. Fuse A 700 max. CB A 600 SCCR (fuse) kA 18 max. Fuse A 700 Class L SCCR (CB) kA 65 max. CB A 250 SCCR (fuse) kA 18 max. Fuse A 700 Class J SCCR (CB) kA 18 max. CB A 600 LRA 480V 60Hz 3phase A 2050 FLA 480V 60Hz 3phase A 300 LRA 600V 60Hz 3phase A 1800 FLA 600V 60Hz 3phase A 250 480 V High Fault 600 V High Fault Special Purpose Ratings Deﬁnite Purpose Ratings (100,000 cycles acc.
PAGE 7
10.11 Short-circuit rating Is the panel builder's responsibility. The speciﬁcations for the switchgear must be observed. 10.12 Electromagnetic compatibility Is the panel builder's responsibility. The speciﬁcations for the switchgear must be observed. 10.13 Mechanical function The device meets the requirements, provided the information in the instruction leaﬂet (IL) is observed. Technical data ETIM 7.
PAGE 8
Characteristics on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA 06/18/2021 Eaton 274190 ED2021 V80.
PAGE 9
Normal switching duty Normal AC induction motor Operating characteristics Switch on: from stop Switch oﬀ: during run Electrical characteristics: Switch on: up to 6 x Rated motor current Switch oﬀ: up to 1 x Rated motor current Utility category 100 % AC-3 Typical Applications Compressors Lifts Mixers Pumps Escalators Agitators fan Conveyor belts Centrifuges Hinged ﬂaps Bucket-elevator Air-conditioning systems General drives for manufacturing and processing machines 06/18/2021 Eaton 274190 ED2021 V80.
PAGE 10
Extreme switching duty Squirrel-cage motor Operating characteristics Inching, plugging, reversing Electrical characteristics Make: up to 6 x rated motor current Break: up to 6 x rated motor current Utilization category 100 % AC-4 Typical applications Printing presses Wire-drawing machines Centrifuges Special drives for manufacturing and processing machines 06/18/2021 Eaton 274190 ED2021 V80.
PAGE 11
Switching conditions for 3 pole, non-motor loads Operating characteristics Non inductive and slightly inductive loads Electrical characteristics Switch on: 1 x rated operational current Switch oﬀ: 1 x rated operational current Utilization category 100 % AC-1 Typical examples of application Electric heat 06/18/2021 Eaton 274190 ED2021 V80.
PAGE 12
Short-time loading, 3-pole Time interval between two loading cycles: 15 minutes Dimensions ① DILM820-XHI11(V)-SI ② DILM820-XHI11-SA 06/18/2021 Eaton Industries GmbH http://www.eaton.eu © 06/2021 by Eaton Industries GmbH Eaton 274190 ED2021 V80.