Data Sheet

ManualsBrandsEaton ManualsAutomationDILM400/22(RA250) Electrical contactor 3 makers 200 kW 1 pc(s)

DATASHEET - DILM400/22(RA250)

Contactor, 380 V 400 V 212 kW, 2 N/O, 2 NC, RA 250: 110 - 250 V 40 - 60

Hz/110 - 350 V DC, AC and DC operation, Screw connection

Part no. DILM400/22(RA250)

Catalog No. 208209

Alternate Catalog

No.

XTCE400M22A

EL-Nummer

(Norway)

4134085

Delivery program

Product range   Contactors

Application   Contactors for Motors

Subrange   Comfort devices greater than 170 A

Utilization category   AC-1: Non-inductive or slightly inductive loads, resistance furnaces

NAC-3: Normal AC induction motors: starting, switch oﬀ during running

AC-4: Normal AC induction motors: starting, plugging, reversing, inching

Connection technique   Screw connection

Rated operational current

  

AC-3   

380 V 400 V I

A 400

AC-1   

Conventional free air thermal current, 3 pole, 50 - 60 Hz   

Open   

at 40 °C I

A 612

enclosed I

A 450

Conventional free air thermal current, 1 pole   

open I

A 1250

enclosed I

A 1125

Max. rating for three-phase motors, 50 - 60 Hz

  

AC-3   

220 V 230 V P kW 125

380 V 400 V P kW 212

660 V 690 V P kW 300

1000 V P kW 132

AC-4   

220 V 230 V P kW 92

380 V 400 V P kW 160

660 V 690 V P kW 240

1000 V P kW 132

Contact sequence  

Can be combined with auxiliary contact   DILM820-XHI…

Actuating voltage   RA 250: 110 - 250 V 40 - 60 Hz/110 - 350 V DC

Voltage AC/DC   AC and DC operation

Contacts

  

N/O = Normally open   2 N/O

N/C = Normally closed   2 NC

Auxiliary contacts

  

possible variants at auxiliary contact module ﬁtting options   on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA

Side mounting auxiliary contacts  

Instructions   Interlocked opposing contacts according to IEC/EN 60947-5-1 Appendix L, inside

the auxiliary contact module

06/16/2021 Eaton 208209 ED2021 V80.0 EN 1 / 12

Summary of content (12 pages)

PAGE 1
DATASHEET - DILM400/22(RA250) Contactor, 380 V 400 V 212 kW, 2 N/O, 2 NC, RA 250: 110 - 250 V 40 - 60 Hz/110 - 350 V DC, AC and DC operation, Screw connection Delivery program Part no. Catalog No. Alternate Catalog No.
PAGE 2
Auxiliary contacts used as mirror contacts according to IEC/EN 60947-4-1 Appendix F (not N/C late open) Instructions integrated suppressor circuit in actuating electronics 660 V, 690 V or 1000 V: not directly reversing Technical data General Standards IEC/EN 60947, VDE 0660, UL, CSA Lifespan, mechanical AC operated Operations x 10 6 7 DC operated Operations x 10 6 7 Operating frequency, mechanical AC operated Operations/h 2000 DC operated Operations/h 2000 Climatic prooﬁng Damp heat, c
PAGE 3
Tool Main cable Width across ﬂats mm 16 Size 2 Uimp V AC 8000 Rated insulation voltage Ui V AC 1000 Rated operational voltage Ue V AC 1000 between coil and contacts V AC 1000 between the contacts V AC 1000 A 5500 220 V 230 V A 5000 380 V 400 V A 5000 500 V A 5000 660 V 690 V A 5000 1000 V A 950 Control circuit cables Pozidriv screwdriver Main conducting paths Rated impulse withstand voltage Overvoltage category/pollution degree III/3 Safe isolation to EN 61140 Mak
PAGE 4
380 V 400 V Ie A 400 415 V Ie A 400 440V Ie A 400 500 V Ie A 400 660 V 690 V Ie A 325 1000 V Ie A 95 P kWh 220 V 230 V P kW 125 240V P kW 132 380 V 400 V P kW 212 415 V P kW 232 440 V P kW 250 500 V P kW 280 660 V 690 V P kW 300 1000 V P kW 132 220 V 230 V Ie A 296 240 V Ie A 296 380 V 400 V Ie A 296 415 V Ie A 296 440 V Ie A 296 500 V Ie A 296 660 V 690 V Ie A 260 1000 V Ie A 95 P kWh 220 V 230 V P kW 92 240 V
PAGE 5
AC operated Pick-up 0.7 x US min - 1.15 x US max DC operated Pick-up 0.7 x US min - 1.15 x US max AC operated Drop-out 0.2 x US max - 0.6 x US min DC operated Drop-out 0.2 x US max - 0.6 x US min Power consumption of the coil in a cold state and 1.0 x US Note on power consumption Control transformer with uk ≦ 6% Pull-in power Pick-up VA 450 Pull-in power Pick-up W 350 Sealing power Sealing VA 14.2 Sealing power Sealing W 7.
PAGE 6
AC A 15 DC V 250 DC A 1 Short Circuit Current Rating SCCR Basic Rating SCCR kA 30 max. Fuse A 800 max. CB A 600 SCCR (fuse) kA 30/100 max. Fuse A 800/600 Class J SCCR (CB) kA 100 max. CB A 600 SCCR (fuse) kA 30/100 max. Fuse A 800/600 Class J SCCR (CB) kA 30 max.
PAGE 7
10.10 Temperature rise The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices. 10.11 Short-circuit rating Is the panel builder's responsibility. The speciﬁcations for the switchgear must be observed. 10.12 Electromagnetic compatibility Is the panel builder's responsibility. The speciﬁcations for the switchgear must be observed. 10.
PAGE 8
Characteristics on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA 06/16/2021 Eaton 208209 ED2021 V80.
PAGE 9
Normal switching duty Normal AC induction motor Operating characteristics Switch on: from stop Switch oﬀ: during run Electrical characteristics: Switch on: up to 6 x Rated motor current Switch oﬀ: up to 1 x Rated motor current Utility category 100 % AC-3 Typical Applications Compressors Lifts Mixers Pumps Escalators Agitators fan Conveyor belts Centrifuges Hinged ﬂaps Bucket-elevator Air-conditioning systems General drives for manufacturing and processing machines 06/16/2021 Eaton 208209 ED2021 V80.
PAGE 10
Extreme switching duty Squirrel-cage motor Operating characteristics Inching, plugging, reversing Electrical characteristics Make: up to 6 x rated motor current Break: up to 6 x rated motor current Utilization category 100 % AC-4 Typical applications Printing presses Wire-drawing machines Centrifuges Special drives for manufacturing and processing machines 06/16/2021 Eaton 208209 ED2021 V80.
PAGE 11
Switching conditions for 3 pole, non-motor loads Operating characteristics Non inductive and slightly inductive loads Electrical characteristics Switch on: 1 x rated operational current Switch oﬀ: 1 x rated operational current Utilization category 100 % AC-1 Typical examples of application Electric heat 06/16/2021 Eaton 208209 ED2021 V80.
PAGE 12
Short-time loading, 3-pole Time interval between two loading cycles: 15 minutes Dimensions ① DILM820-XHI11(V)-SI ② DILM820-XHI11-SA 06/16/2021 Eaton Industries GmbH http://www.eaton.eu © 06/2021 by Eaton Industries GmbH Eaton 208209 ED2021 V80.