Technical Specifications EATON RF System Wiring Examples . . . . . . . . . . . . . . . . . . . Technical Specifications . . . . . . . . . . . . . Installation . . . . . . . . . . . . . . . . . . . . . . . . Functions . . . . . . . . . . . . . . . . . . . . . . . . .
EATON RF SYSTEM EATON RF system Wiring Examples for Switching Actuator CSAU-01/01 voltage-free multiphase e.g. heating, garage door opener e.g. electric sauna e.g. lamps, pumps, fans and sound signal emitters Switching fluorescent lamps with a CSAU-01/01 actuator SA cycles 55000 26000 14000 8000 7000 Total capacitor value 25µF 55µF 90µF 100µF 130µF The numbers of SA cycles specified are approximate values and may vary depending on the local conditions prevailing in each case.
EATON RF SYSTEM Wiring Examples for Switching Actuator CSAU-01/02, CSAU-01/04 e.g. lamps, pumps, fans, sound signal emitters e.g. dimming via a push-button dimmer input release signals for other control devices e.g. garage door e.g. electric heating (heating contactor) e.g. release for heating, air conditioning or ventilation e.g.
EATON RF SYSTEM Wiring Examples for Switching Actuator CSAU-01/03 e.g. lamps, pumps, fans, sound signal emitters e.g. electric heating (heating contactor) e.g. electric sauna Switching fluorescent lamps with a CSAU-01/03 actuator SA cycles 37000 15000 7000 4000 2000 Total capacitor value 25µF 55µF 90µF 107µF 133µF The numbers of SA cycles specified are approximate values and may vary depending on the local conditions prevailing in each case.
EATON RF SYSTEM Wiring Examples for Shutter Actuator CJAU-01/02, CJAU-01/03 single double - correct double or multiple - wrong separation relay Conventional shutters and blinds max.
EATON RF SYSTEM Wiring Examples for Dimming Actuator CDAU-01/02 ! ATTENTION! max. 250 W Electronic LV- halogen transformer Incandescent lamps Low-voltage halogen lamps with electronic transformer Low-voltage halogen lamps with ferromagnetic transformer not authorized! Wiring Examples for Dimming Actuator CDAU-01/03 ! ATTENTION! max.
EATON RF SYSTEM Wiring Examples for Energy Meter Sensor CEMU-01/02 Energy meter sensor: Make sure the wiring is correct! ...
EATON RF SYSTEM Wiring Examples for Binary Input Unit CBEU-02/01 Interface for wind sensor 2x conventional push-buttons or shutter pushbuttons 2x conventional switches Rain sensor conventional push-buttons and conventional switches Different phases - correct wind sensor for shutters/blinds Different phases - incorrect Rain sensor Rain sensor for skylights Not authorized! Mode 2 2x conventional switches Integration: twilight switch e.g.
EATON RF SYSTEM Wiring Examples of Binary Input Unit CBEU-02/01 (continued) Conversion: Information from EASY to wireless system Conversion: Information from wireless system to EASY Integration: - logical functions - timers - time controls - meters - light control - etc. Switching via Telephone To the telephone installation External push-button 1 Attention: Choose a protective device for the user’s power circuit in compliance with the maximum contact load.
EATON RF SYSTEM Wiring Examples of Binary Input Unit CBEU-02/02 CSEZ-01/06 CSEZ-01/25 CSEZ-01/07 CSEZ-01/06 CSEZ-01/25 CSEZ-01/07 CSEZ-01/06 CSEZ-01/25 CSEZ-01/07 CSEZ-01/06 CSEZ-01/25 CSEZ-01/07 10
EATON RF SYSTEM Wiring Example GSM-Modem CKOZ-00/02, CKOZ-00/06 Power Supply Antenna 9-pole RS232-Cable 1.8m Wiring Examples Communication-Interface CKOZ-00/03 KommunikationsCommunication Interface Schnittstelle USB USB 1,8m USBKabel Cable (A-B) (A-B) 1.8m USB (Type B) RJ12 (f. RS232) KommunikationsCommunication Interface Schnittstelle RS232 + USB USB 1,8m USBKabel Cable (A-B) (A-B) 1.8m PC PCis istmaster Master RS232 RS232 Cable (RJ12(RJ12 - SubD- 9, RS232 Kabel Connection) 1.
EATON RF SYSTEM Wiring Examples for Analogue Input CAEE-02/01 CSEZ-01/14 CSEZ-01/15 max. 20m (e.g. LiYCY, CAT5) CMMZ-00/12 CMMZ-00/13 CSEZ-01/16 max. 20m (e.g. LiYCY, CAT5) CMMZ-00/12 CMMZ-00/13 ! PT1000 max. 20m (e.g. LiYCY 2x0.14) max. 20m (e.g. LiYCY, CAT5) CSEZ-01/17 CMMZ-00/12 CMMZ-00/13 PT1000 max. 20m (e.g. LiYCY 2x0.
EATON RF SYSTEM Wiring Examples for Analogue Actuator CAAE-01/01 e.g. motor speed controller e.g. mixer controller e.g. dimmer or power dimmer e.g. heating, air conditioning, ventilation Wiring Examples for Analogue Actuator CAAE-01/02 e.g dimmer or power dimmer e.
EATON RF SYSTEM Wiring Examples for Dimming Actuator CDAE-01/01 Incandescent lamps Low-voltage halogen lamps with electronic transformer Electronic LV- halogen transformer Low-voltage halogen lamps with coil transformer not authorized! Energy saving lamps not authorized! Fluorescent lamps not authorized! 14
EATON RF SYSTEM Wiring Examples for Dimming Actuator CDAE-01/02 Incandescent lamps Low-voltage halogen lamps with electronic transformer Electronic LV- halogen transformer Dimmable with phase section LED-lamps, e.g. Philips Dimmable with phase section energy saving lamps, e.g.
EATON RF SYSTEM Wiring Examples for Impulse Counting Input 2-way CIZE-02/01 Power supply unit CMMZ-00/12 CMMZ-00/13 S0 Energy meter, 230 VAC S0 Consumption meter, 24 VDC Wiring Examples for Motion Sensor CSEZ-01/12 Mode 2 2x conventional switches Conventional installation Connection to EATON RF system via a 230V binary input (CBEU-02/01) 16 Connection to EATON RF system via a binary input with battery (CBEU-02/02) not authorized!
EATON RF SYSTEM Wiring Examples for Presence Dectector CSEZ-01/13 Conventional installation Connection to EATON RF system via a 230V binary input (CBEU-02/01) Connection to EATON RF system via a binary input with battery (CBEU-02/02)) Mode 2 2 x conventional switches Mode 2 2 x conventional switches A: pink B: orange Wiring Examples for Water Leakage Sensor CSEZ-01/18 Connection to EATON RF system via a binary input with battery (CBEU-02/02) A: pink B: orange white Connection to EATON RF system via
EATON RF SYSTEM Wiring Examples for Radiator Valve CHVZ-01/01 CDAU-01/03 CHVZ-01/01 230VAC/2W CSAU-01/01 CSAU-01/02 CSAU-01/03 CHVZ-01/01 230VAC/2W CDAU-01/02 CHVZ-01/01 230VAC/2W not authorized! Wiring Examples for the Compact Signal Emitter CSGZ-02/01 Siren (230 VAC) Flashing light (230 VAC) Wiring Examples for Flashing Light Signal Emitter CSGZ-01/02 Flashing light (230 VAC) 18
EATON RF SYSTEM Battery Back-up for Safety Function with Uninterrupted Power Supply (UPS) Siren (230VAC) Flashing light (230VAC) Uninterrupted power supply with battery back-up Flashing light (230 VAC) UPS Room Manager with safety function 19
EATON RF SYSTEM Overvoltage protection with inductive loads - fluorescent lamps Is on the same phase, on which e.g. also CSAU-01/0x, CJAU-01/0x, CDAU-01/0x, CSAP-01/0x, CDAP-01/0x, and/or CBEU-02/01 are connected, an inductance (e.g. fluorescent lamp), an overvoltage protection is as in following examples to use.
EATON RF SYSTEM Overvoltage protection with inductive loads - fluorescent lamps (continued) fluorescent lamp fluorescent lamp fluorescent lamp fluorescent lamp fluorescent lamp fluorescent lamp fluorescent lamp fluorescent lamp fluorescent lamp fluorescent lamp fluorescent lamp fluorescent lamp 21
EATON RF SYSTEM Connection example for energy sensor CEMU-01/04 PV modules Note: The reading on the PV inverter might be different than the reading on the RoomManager. Reason: Leakage and drop of voltage at the wiring and/or the transmitting intervals from the energy sensor to the Room-Manager and the update intervals at the PV-inverter display.
EATON RF SYSTEM Connection example for CRMA-00/01 - CRMA-00/22 23
EATON RF SYSTEM Switching Actuator CSAU-01/01 Technical Specifications Power supply Connections Load 45.5 26 230VAC, 50Hz Single-wired 1.
EATON RF SYSTEM Shutters/Blinds Actuator CJAU-01/02, CJAU-01/03 Technical Specifications Power supply Connections Load 45.5 26 230VAC, 50Hz Single-wired 1.
EATON RF SYSTEM Reduction of power for CDAU-01/02 Massive type of wall One device Reduction of power Hollow type of wall with thermal insulation - One device Massive type of wall with several devices Hollow type of wall with thermal insulation and several devices Ambient temperature Router CROU-00/01 Technical Specifications Power supply Connections Power cinsumption Pre-protection Frequency Type of transmission Indoor range 45.5 26 230VAC, 50Hz Single-wired 1.5mm² connections 0.
EATON RF SYSTEM Energy sensor CEMU-01/02, CEMU-01/04 45.5 26 Technical specifications Power supply Connections Power consumption Pre-protection Max. current Min. output Max. output Accuracy Measurement units 230VAC, 50Hz Lead wires solid, 2.
EATON RF SYSTEM Binary Input Unit CBEU-02/01 Technical Specifications Power supply Connections Input voltage 26 45.5 230VAC, 50Hz Single-wired 1.
EATON RF SYSTEM Home Manager CHMU-00/02 Installation depth Technical Specifications Power supply 230VAC/50Hz Power consumption - standby: 6VA (with background lighting switched off) Power consumption - normal: 8VA (with background lighting switched on) Fine-wire protection in the device T 63 mA Pre-protection Power circuit breaker 16A, charateristic C Frequency 868,300 MHz Type of transmission Bi-directional, via coded telegrams Indoor range Typically 30 - 50m, 2 walls + 1 ceiling (depending on wall thick
EATON RF SYSTEM Push-button C100, CTAA-01/02 Technical Specifications Power supply Frequency Type of transmission Indoor range Service life of the battery Degree of protection Degree of soiling Operating temperature Storage/transportation temp.
EATON RF SYSTEM Push-button universal 55x55 mm without LED CTAA-01/04, CTAA-02/04, CTAA-04/04 Technical Specifications Power supply 3V via CR2450N battery Number of rockers depending on type Frequency 868,300MHz Type of transmission Bi-directional, via coded telegrams Indoor range Typically 30 - 50m, 2 walls + 1 ceiling (depending on wall thickness, material, used rocker and frame !!) Service life of the battery Approx.
EATON RF SYSTEM Push-button universal 55x55 mm with LED CTAA-01/04-LED, CTAA-02/04-LED, CTAA-04/04-LED Technical Specifications Power supply 3V via CR2450N battery Number of rockers depending on type Frequency 868,300MHz Type of transmission Bi-directional, via coded telegrams Indoor range Typically 30 - 50m, 2 walls + 1 ceiling (depending on wall thickness, material, used rocker and frame !!) Service life of the battery Approx.
EATON RF SYSTEM Push-button MEM series F9401, F9402, F9404 — Mounting plate MEM series F9400 Technical Specifications Power supply 3V via CR2450N battery Number of rockers depending on type Frequency 868,300MHz Type of transmission Bi-directional, via coded telegrams Indoor range Typically 30 - 50m, 2 walls + 1 ceiling (depending on wall thickness, material, used rocker and frame !!) Service life of the battery Approx.
EATON RF SYSTEM Room Controller CRCA-00/04, CRCA-00/05, CRCA-00/06, CRCA-00/07 Technical Specifications Power supply 3V via 2x LR03 (AAA) CRCA-00/04, CRCA-00/05, CRCA-00/06, CRCA-00/07 Channel A: Temperature range 0 - 40°C Standard setting 21°C, +/- 3°C variable by adjustment wheel Hysteresis +/- 0.5°C CRCA-00/05, CRCA-00/07 Channel B: Permitted relative air humidity Operating range Accuracy within the measuring range Long-term stability at 20-30°C / 20-80% rel.hum.
EATON RF SYSTEM Room Manager CRMA-00/01 up to CRMA-00/10, CRMA-00/19 up to CRMA-00/122 (without Bluetooth), CRMA-00/11 up to CRMA-00/18 (with Bluetooth) CRMA-00/02 Technical Specifications Power supply 230VAC/50Hz Power consumption: CRMA-00/01 up to CRMA-00/10 CRMA-00/19 up to CRMA-00/22 CRMA-00/11 up to CRMA-00/18 Pre-protection Frequency Type of transmission Indoor range Power reserve - time: Interfaces Degree of protection Degree of soiling Operating temperature Storage/transportation temp.
EATON RF SYSTEM Ethernet Communication Interface ECI LAN, CCIA-02/01, CCIA-03/01 Technical Specifications Power supply CCIA-02/01: CCIA-03/01: Power consumption Display LED orange, LAN PWR: LED green, LAN Data: LED red, Prog ON/OFF: Operation Supply switch: Prog ON/OFF push-button: LAN Network - factory setting Frequency Type of transmission Indoor range Colour of the enclosure Degree of protection Degree of soiling Operating temperature Storage/transportation temp.
EATON RF SYSTEM PIR Motion Sensor CBMA-02/01 72 133 56 Technical Specifications Power supply 3V über 2x LR03 (AAA) Motion sensor PIR-Sensor Area covered 110°, max. 12m at a mounting height of 2.
EATON RF SYSTEM Power Supply Unit for Motion Sensor CMMZ-00/08 Technical Specifications Power supply Connections Output voltage Output power 230VAC, 50Hz Connecting wires 1.5mm2 max. 14.5 VAC (no-load operation) max. 0.25VA, short-circuit proof max. 1 PIR-motion sensor, CBMA-02/01 Pre-protection Power circuit breaker 16A, characteristic B Degree of protection IP20 Degree of soiling 2 Operating temperature -5 to +45°C Storage /transportation temp.
EATON RF SYSTEM Switching Actuator Adapter Plug - British Standard CSAP-01/03 Technical Specifications Power supply Plug system Load 230VAC, 50Hz British Standard, with children protection 230VAC, 50Hz, 8A resistive load Internal protection through thermal protection Pre-protection Power circuit breaker 16A, characteristic C Frequency 868,300 MHz Type of transmission Bi-directional, via coded telegrams Indoor range Typically 30 - 50m, 2 walls + 1 ceiling (depending on wall thickness and material !!) Degree
EATON RF SYSTEM Dimming Actuator Adapter Plug - Earthing Pin CDAP-01/12 Technical Specifications Power supply Plug system Load 230VAC, 50Hz Earthing pin, with children protection 250W 230VAC, 50Hz, incandescent lamps or electronic transformers, Reversed phase control, Internal overload and short-circuit protection Pre-protection Power circuit breaker 16A, characteristic C Frequency 868,300 MHz Type of transmission Bi-directional, via coded telegrams Indoor range Typically 30 - 50m, 2 walls + 1 ceiling (dep
EATON RF SYSTEM Energy Meter Sensor Adapter Plug - Side Earthings CEMP-01/11 Technical Specifications Power supply Plug system Power consumption Max. current Min. power Max. power Accuracy Units of measurement 230VAC, 50Hz Side earthings, with children protection 0.
EATON RF SYSTEM Energy Meter Sensor Adapter Plug - British Standard CEMP-01/13 Technical Specifications Power supply Plug system Power consumption Max. current Min. power Max. power Accuracy Units of measurement 230VAC, 50Hz British Standard, with children protection 0.
EATON RF SYSTEM Analogue Input CAEE-02/01 Technical Specifications Power supply Power consumption Power supply for sensors device Fine-wire fuse in the device Inputs: IN1, IN2 12-24VDC, external power supply unit 0.
EATON RF SYSTEM Dimming Actuator CDAE-01/01, CDAE-01/02 Technical Specifications Power supply All connections Load 230VAC, 50Hz Single-wired 1.
EATON RF SYSTEM Dimming Actuator CDAE-01/01, CDAE-01/02 (Continuation) Reduction of power CDAE-01/01 Massive type of wall One device Hollow type of wall with thermal insulation. One device. Reduction of power Massive type of wall with several devices Hollow type of wall with thermal insulation and several devices Ambient temperature Reduction of power CDAE-01/02 Massive type of wall One device Hollow type of wall with thermal insulation. One device.
EATON RF SYSTEM Impulszähleingang CIZE-02/01 Technical Specifications Power supply Power consumption Fine-wire fuse in the device Inputs: IN1, IN2 Max. frequency input Kind of counter Frequency Type of transmission Indoor range 12-24VDC, external power supply unit 0.
EATON RF SYSTEM 2-Channel Remote Control CHSZ-02/02 Technical Specifications Power supply Channels Display: 1 yellow LED Operation Frequency Type of transmission Indoor range Service life of the battery Degree of protection Degree of soiling Operating temperature Storage/transportation temp.
EATON RF SYSTEM 12-Channel Remote Control with Display CHSZ-12/04 Technical Specifications Power supply Channels Displays LCD-Display 1 LED yellow Operation Power reserve of time setting Frequency Type of transmission Indoor range Service life of the battery Interfaces Degree of protection Degree of soiling Operating temperature Storage/transportation temp.
EATON RF SYSTEM USB Configuration Stick CKOZ-00/13 Technical Specifications Power supply Connection Indication Frequenzy Type of transmission Indoor range Degree of protection Operating temperature Storage/transportation temp.
EATON RF SYSTEM RS232 Configuration Interface CRSZ-00/01 Technical Specifications Power supply Via storage-battery pack Rechargable through power pack unit included in delivery Connections 12VDC jack,140 mA Data via 9-pole SUBD 3 status LEDs Frequency 868,300 MHz Type of transmission Bi-directional, via coded telegrams Indoor range Typically 30 - 50m, 2 walls + 1 ceiling Independence of storage batt. Approx.
EATON RF SYSTEM BOS/COS Interface CKOZ-02/08 Technical Specifications Power supply 50 33 24 90 Supply cable Power consumption Input Indication Frequency Type of transmission Indoor range Degree of protection Degree of soiling Operating temperature Storage/transportation temp.
EATON RF SYSTEM GSM-Modem CKOZ-00/02, CKOZ-00/06 Technical Specifications Power supply of 68 Connections 33 74 Frequency Type of transmission Indication Degree of protection Degree of soiling Operating temperature Storage/transportation temp.
EATON RF SYSTEM Surface-mounted Window Contact CSEZ-01/06, CSEZ-01/25 Switch 28 24 6,5 Technical Specifications Power supply Contact connections Max. distance Type of contact via binary input CBEU-02/02 2-wire cable, white 15 mm (contact/magnet) CSEZ-01/06: normally open contact CSEZ-01/25: normally closed contact Max. contact load 100 VDC, 0.5A Degree of protection IP20 Operating temperature -5 to +45°C Storage/transportation temp.
EATON RF SYSTEM Diagnostic Device CSEZ-01/11 Technical Specifications Power supply Display 9V via battery 6LR61 10 LEDs orange, Display of reception quality is an approx. value, accurate determination via CRSZ-00/01. Respect information on the device. Minimum distance to other electronic devices (RF, TV, monitors etc.): 3-4m Operation ON/OFF switch Frequency range 868 MHz, ± 300kHz Service life of the battery Approx.
EATON RF SYSTEM Brightness Sensor - Indoor 0-10VDC CSEZ-01/14 Technical Specifications Power supply Brightness measuring ranges Output voltage Internal resistance Degree of protection Operating temperature Storage/transportation temp.
EATON RF SYSTEM VOC Air Quality Sensor 0-10VDC CSEZ-01/16 Technical Specifications Power supply Power consumption All connections Sensor Pre-heating time of sensor Output voltage 15-24VDC ±10% max. 50mA/24VDC Screw-type terminals, max. 1.5mm2 Mixed gas VOC approx. 30 min 0-10VDC linear to air quality max. 10mA Degree of protection IP20 Operating temperature -10 to +50°C Permitted relative air humidity max. 85%rF Storage/transportation temp.
EATON RF SYSTEM Humidity Sensor - Outdoor 0-10VDC with Temperature PT1000, CSEZ-01/17 Technical Specifications Power supply Power consumption All connections Sensor 1 Operating range Measuring range Output voltage 15-24VDC ±10% max. 2mA/24VDC Screw-type terminals, max. 1.5mm2 capacitive sensor, relative humidity 0-100% 5-95% rel. humidity 0-10VDC 0% rel. humidity corresponding to 0VDC, 100% rel. humidity corresponding to 10VDC Accuracy at 24VDC and 21°C(+-5k) ±3% rel. humidity (in the range of 30-80% rel.
EATON RF SYSTEM Multi-HeatingActuator CHAZ-01/12 Technical Specifications Power supply Connections Power consumption Fuse Frequency Type of transmission Indoor range Thermostat types Valve drive types Pump switching output CO input Dew point sensor input Degree of protection Operating temperature Storage/transportation temp. Dimensions of the enclosure Approval: 230V/50Hz ± 10% Plug-in, singlecore/multicore wires (0,25 - 1,5 mm2) 50 VA max.
EATON RF SYSTEM Smoke Detector - Battery-Powered CSEZ-01/19 Technical Specifications Power supply 9V via a 6LR61, 4022 9V, CP-V9J, U9VL-J, GPCR-V9, U9VL-J-P Sensor Photo-electronic smoke detector, power supplied by battery (stray light sensor according to Tyndall effect) Operating element Test button (activate for at least 1 second) Alarm output Acoustic signal emitter, approx.
EATON RF SYSTEM Heating Actuator or Electrical Heater Panels CHAZ-01/01 Technical Specifications Power supply Anschlüsse Leistungsaufnahme: Pre-protection Frequency Type of transmission Indoor range 230-400VAC, 50Hz Steckkontakte 0.
EATON RF SYSTEM Configuration possibilities The configurations specified here are just a few examples. Other combinations are of course possible, too. 1. "Heating actuator with electrical panel” only, without any assigned sensors Application: Backup mode = Emergency mode Real temperature: Internal sensor in the electrical panel Set-point temperature: Handwheel on electrical panel Comfort: Eco: Off: - 2.
EATON RF SYSTEM 4.
EATON RF SYSTEM 5.
EATON RF SYSTEM 6.
EATON RF SYSTEM RF Radiator Thermostat CHVZ-01/03 Technical Specifications Power supply Connection Battery life Frequency Display Adjustment travel Adjustment force Degree of protection Operating temperature Max. surface temperature Colour of the enclosure Total dimensions Approval RF valves that are compatible 1) Without an adapter Manufacturers/Types: 3V via battery (2x 1.5V AA) M30 x 1.5 approx. 2 years 868,300 MHz LC display 4.2 mm max.
EATON RF SYSTEM Radiator Valve NC CHVZ-01/01 Technical Specifications Power supply Connection plug-in Power consumption Pre-protection Regulation distance Regulation force Type Miscellaneous 230VAC +/- 10%, 50/60Hz 2x0,75mm2, 1m 2W Power circuit breaker 16A, charateristic C 4 mm 100 N +-5% NC (closed when not energized) First Open Function Plug-type fitting Function display Adjustment check Types of fittings: depending on valve adapter Degree of protection IP54 Degree of soiling 2 Medium temperature 0 to 1
EATON RF SYSTEM Compact Signal Emitter CSGZ-02/01 Technical Specifications Power supply Connections Pre-protection Flashing light Flashing frequency Flashing energy Power consumption Siren Audio pressure Power consumption Degree of protection Degree of soiling Operating temperature Storage/transportation temp. Colour of the enclosure Dimensions of the enclosure Approval 230VAC, 50Hz Screw-type terminal, 1.5mm² Power circuit breaker 16A, charateristic C approx. 0.8 Hz approx. 2 Ws approx.
EATON RF SYSTEM Adhesive Strips CMMZ-00/01, CMMZ-00/24 Technical Specifications Material Colour Content of the set Size Double-coated adhesive strips Duolomont Graphite black, similar to RAL 9011 For 10 push-buttons (20 adhesive strips) LxWxH - 45 x 7 x approx.
EATON RF SYSTEM Cover Foil white CMMZ-00/04, CMMZ-00/27 Technical Specifications Material Colour Content of the set Cleaning Size Synthetic foil White, similar to RAL 9003 for 10 push-buttons (10 pcs. of foil) Damp cloth LxWxH - 80 x 80 x 0.5mm Cover Foil grey CMMZ-00/05, CMMZ-00/28 Technical Specifications Material Colour Content of the set Cleaning Size Synthetic foil Grey, similar to RAL 7001 for 10 push-buttons (10 pcs. of foil) Damp cloth LxWxH - 80 x 80 x 0.
EATON - WIRELESS SYSTEM Setting in “BASIC MODE” In “Basic Mode” the functions of the devices can be assigned through activating the programming button and the respective push-button. Easy, without any complicated tools, PC or setting of DIP-switches etc. Increasing the range through "Routing" (see Comfort Mode) is not possible in Basic Mode.
EATON - WIRELESS SYSTEM Installation 1 Simply stick the switch, temperature control etc. onto the wall 5 Installation of an actuator in the switch box with wireless push-button as a combined solution 9 Battery easy to replace, Service life of battery for push-button approx.
EATON - WIRELESS SYSTEM Protective Device Protection of actuators through 16A-Miniature Circuit Breakers, characteristic C, e.g. PLSM-C16/1N Instructions for Installation in “BASIC MODE” Transmitting range: approx. 30-50 m indoors, typically 2 walls + 1 ceiling (depending on wall thickness and material, see page after the next “RF - Building Penetration Capacity”).
EATON - WIRELESS SYSTEM Installation options: Actuators in the branch box Distributor NO NEED to provide a major-size installation distributor. The actuators can be installed in branch boxes. Installation options: Actuators installed in the light fixtures Distributor NO NEED to provide a major-size installation distributor. Some of the actuators can be installed in branch boxes (blinds) and others in the light fixtures (lighting).
EATON - WIRELESS SYSTEM RF - Building Penetration Capacity Brick-type wall approx. 60-90% Wood and wood frames with sandwichtype plaster board approx. 80-95% Concrete with steel reinforcement approx. 20-60% Metal walls approx. 0-10% Ordinary glass approx. 70-90% Insulating glass (metallized) approx. 30-60% Synthetic material approx. 80-95% ! Information: The percentages given are guideline values only. They may vary subject to the respective local conditions.
EATON - WIRELESS SYSTEM Functions of the switching actuator in Basic-Mode RF Push-button: ON / OFF Remote control: ON / OFF Binary input: Mode 1: Both channels: current impulse Mode 2: Both channels: ON / OFF Mode 3: Channel A: current impulse; channel B: ON / OFF Mode 4: Channel A: ON; channel B: OFF Room temperature control: Too cold: ON; too warm: OFF Mains supply restored: With low batterie: Last value Flashing Functions of the dimming actuator in Basic-Mode RF Push-button: ON / OFF and b
EATON - WIRELESS SYSTEM Functions of the analogue actuator in Basic-Mode RF Push-button: ON / OFF and brighter/darker Remote control: ON / OFF and brighter/darker Binary input: Mode 1: Both channels with push-button and dimming function Mode 2: Both channels only ON / OFF without brighter/darker function Mode 3: Channel A: push-button and dimming function ; Channel B: only ON / OFF without Mode 4: Channel A: ON and brighter; Channel B: OFF and darker brighter/darker function Room temperature co
EATON - WIRELESS SYSTEM Setting Card “BASIC MODE” Devices - Overview CTAA-01/0X CTAA-02/0X CBEU-02/0X CSAU-01/0X CSAP-01/0X CJAU-01/0X CDAU-01/0X CDAP-01/0X CRCA-00/0X CAAE-01/0X CHSZ-00/0X Allocate functions Delete individual sensors Totally delete an actuator Manual operation 77
EATON - WIRELESS SYSTEM Functions overview for actuators in Comfort Mode (by means of MRF-Software and PC) For each sensor assigned (max.
EATON - WIRELESS SYSTEM Functions overview for actuators in Comfort Mode (by means of MRF-Software and PC) - continued For each sensor assigned (max.
EATON - WIRELESS SYSTEM Functions overview for actuators in Comfort Mode (by means of MRF-Software and PC) - continued For each sensor assigned (max.
