Compact Loader User Manual
EATON Char-Lynn Steering Catalog C-STOV-MC001-E1 July 2006 73
100 254,0 [10.00]
120 304,8 [12.00]
140 355,6 [14.00]
160 406,4 [16.00]
026 66,1 [ 2.60]
036 92,3 [ 3.63]
062 157,3 [ 6.19]
081 206,6 [ 8.13]
103 260,2 [10.24]
111 282,8 [11.13]
121 308,2 [12.13]
162 409,3 [16.11]
182 461,1 [18.15]
257 651,6 [25.65]
276 701,9 [27.63]
302 765,9 [30.15]
329 835,7 [32.90]
AAA 190,5 [ 7.50] Above Pivot
546,4 [21.51] Below Pivot
AAB 190,5 [ 7.50] Above Pivot
101,6 [ 4.00] Below Pivot
AAC 127,0 [ 5.00] Above Pivot
127,0 [ 5.00] Below Pivot
12-16 Horn Wire Feature 00000 No Horn Wire
(page 79) 1A045 Single Horn Wire
2B045 Two Horn Wires
17 Horn Brush Wire 0 None—Select When No Horn Wire Used
Terminal End D SAE J928 Pin and Double End Connector
(page 79) K Blade Receptacle—Insulated
(Compatible with SAE J858a)
18,19 Shaft End Wire 00 None
Terminal 01 One Horn Button (Only with One Horn Wire)
(page 79) 02 One Horn Button with Wire Eyelet
(Select with Two horn Wire)
08 Tinned Bare Wire End
20,21 Special Feature 00 None
22 Eaton Assigned
Design Code B For Tilt columns
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
A C K 00
Nos Feature Code Description Nos Feature Code Description
Steering System
Components
Columns
Model Code,
Ordering
Information
The following 22-digit coding system has been developed to
identify all of the configuration options for steering columns.
Use this model code to specify a steering column with the
desired features. All 22 digits of the code must be present
when ordering. You may want to photocopy the matrix below
to ensure that each number is entered in the correct box.
1,2,3 Product Series ACK Steering Column
4,5 Jacket/Base Type SJ Standard (38 mm [1.50 inch] O.D.)
(page MN Round Series 5 (38mm [1.5 inch] O.D.)
74) HG Heavy Wall (41,4 [1.63 inch] O.D.)
Tabbed Flange
SH Standard With flat Flange
(38mm [1.50 inch] O.D.) (No Tabs)
TJ Tilt Column with Flat Flange, Mechanical Push
Button
6 Lower Shaft End 1 12 Tooth Spline for Steering Unit
(see page 3 3/4 inch “D” Section
75) (for Noise Isolator)
7,8 Upper Shaft End AJ Standard for all rigid and tilt columns
(see illustrations Available with or without Horn Wire
and specifications MJ Available with or without Horn Wire
page DN Not Available with Horn Wire
76, 77) EJ Not Available with Horn Wire
GC Not Available with Horn Wire
CL Not Available with Horn Wire
PT Available with or without Horn Wire
SV Available with or without Horn Wire
YM Not Available with Horn Wire
9,10,11 Jacket Length 022 56,6 [ 2.23]
mm [in.] 033 82,8 [ 3.26]
(Suggested Std. 058 147,8 [ 5.82]
Dim.) 078 197,1 [ 7.76]
099 250,7 [ 9.87]
108 273,3 [10.76]
118 298,7 [11.76]
157 399,8 [15.74]
178 451,6 [17.78]
253 642,1 [25.28]
273 692,4 [27.26]
298 756,4 [29.78]
325 826,3 [32.53]
060 152,4 [ 6.00]
080 203,2 [ 8.00]
Tilt Column
BOLT & NUT KITS
Separate kits are available for purchase to use with steering columns
Metric Cap Screw Kit M10 x 1.5 Thread x 20mm Lenth (Qty 4) 9900157-000
Standard Cap Screw Kit .375-16 UNC Thread x .75" Length (Qty 4) 9900158-000
Metric Jam Nut Kit M18 x 1.5 (Qty 1) 9900159-000
Hex Nut Kit 13/16-20 NEF (Qty 1) 9900160-000
Hex Nut Kit 1 1/2 - 12 UNF (Qty 1) 9900161-000