User manual

EN Instructions
Article number: 06619
Dear Customer,
We are delighted that you have chosen this LED double fl ood-
light with motion detector.
Before using the article for the fi rst time, please read the instruc-
tions through carefully and keep them for future reference. If the
article is given to someone else, it should always be accompanied
by these instructions.
If you have any questions about the article and about spare parts/
accessories, contact the customer service department via our web-
site: www.service-shopping.de
Explanation of Symbols
Read through the safety instructions carefully and fol-
low them to prevent personal injury and damage to
property.
Supplementary information
Read operating instructions before use!
Protection class II
Operation
The motion detector responds to moving heat sources within its
detection range and activates the LED fl oodlights. This switches
off again after a preset interval ranging between 3 seconds and
7 minutes. The sensitivity of the motion detector can be steplessly
adjusted. The twilight switch insures that the motion detector oper-
ates either night and day or only during darkness.
IMPORTANT INSTRUCTIONS
■ The article is designed to light up automatically when persons
are detected by the motion detector. It is not suitable for other
purposes.
■ The article is designed for personal use only and is not intended
for commercial applications. Use the article only as described
in the instructions. Any other use is deemed to be improper.
Keep the instructions in a safe place.
CAUTION: risk of electric shock!
Electrical installation may only be implemented by a quali-
fi ed electrician in compliance with national installation regu-
lations.
Before installing, maintaining or cleaning the article you
should disconnect it from the electricity supply.
You should never try to remove the housing of the motion
detector! It contains components which are live. In addition
this could damage the article. The unauthorised opening of
the housing will render the warranty null and void.
■ CAUTION: Danger of suffocation! Keep the packaging mate-
rial away from children and animals.
■ The article is not a toy! Keep children and animals away from
the article in order to prevent injuries.
■ Only clean the article with a damp, soft cloth and mild deter-
gent if necessary. Do not use any corrosive or abrasive clean-
ing agents! They could damage the surface.
■ For reasons of safety and approvals, any conversion and/or
modifi cation of the article is prohibited.
■ The warranty does not cover any defects which are caused by
failure to comply with these instructions and the safety guide-
lines, improper handling, damage or unauthorised attempts at
repair. This also applies to normal wear and tear.
Items Supplied and Article Overview
1 Floodlight
2 Cable
3 Motion detector
4 Adjusting knobs
(on the under-
side)
1
3
2
4
Assembly
CAUTION!
■ The fl oodlight must not be mounted on the ceiling! The mini-
mum distance above the fl oodlight and from its sides must be
30 cm, and 80 cm between the fl oodlight and the object to be
illuminated.
■ The article is splashproof (IP44). In spite of this, however, we
recommend installing the article in a protected location to en-
sure perfect functioning, because the setting knobs are not wa-
terproof.
■ You should select a dry location near a distribution box to
which the cable of the fl oodlight can be connected.
■ The wall and the installation materials (not supplied) must be
able to bear the weight of the fl oodlight.
■ Make sure that you do not drill into or destroy any pipes or
cables. Find out where possible pipes or cables may run
and avoid them.
You will need suitable fi xings (not supplied) for your wall and
an electric drill.
1. Hold the article against the wall and mark the position of the
holes. Make sure that the markings are horizontal.
2. Drill the holes.
3. Attach the article to the wall with suitable screws and if neces-
sary wall plugs (not supplied).
Electrical Installation
CAUTION Risk of electric shocks!
■ Electrical installation may only be implemented by a quali-
fi ed electrician in compliance with national installation
regulations.
■ Work on the article must only be implemented when it is discon-
nected from the power supply. For this purpose the fuse for the
circuit should be switched off. Check whether the connecting
lead is disconnected from the power supply.
The precondition for the installation of the article is an exist-
ing, properly connected distribution box.
1. Open the distribution box.
2. Insert the cable (2) of the article into the distribution box. It may
be necessary to remove the terminal strips from the cable fi rst.
3. With the aid of the terminal strips you clamp the leads (brown,
blue) to the corresponding connections in the distribution box.
Brown L live conductor
Blue N neutral conductor
06619_DE-EN-FR-NL_A4_V4.indb 306619_DE-EN-FR-NL_A4_V4.indb 3 18.08.2017 08:35:0418.08.2017 08:35:04