User's Manual

NOTE:(1-7)
Wiring Diagram of EASYGUARD EC002
See DIP switch setting
on Control module
ENGINE
STOP
START
Orange Switch
Blue LED light
Green LED light
Brown 12V
Push start button
Orange wire connect with ACC
White wire connect with ignition 1
Brown wire connect with ignition 2
Red wire connect with +12V
Red wire connect with +12V
Yellow wire connect with Starter
cut the key and keep
1mm outside
White
( see note 8)
or blue
( see note 9),
3Pin
3 color wire (see Note 8) or shock sensor (see
note 9)
Note 8:
If the alarm equip with 3 color wire, which is used
to connect with immobilizer bypass wire or G R
status wire or status output wire
Choose one method as below:
No need to connect orange wire for all
W
1.If there is only one +12V wire in
your ignition wire harness, then
connect it with both +12V wires in
EC002
2.White ignition 1 wire: When turn
the key to ON or ACC, this wire with
electricity, when starting the car, this
wire still with electricity
3.Brown ignition 2 wire: When turn
the key to ON or ACC, this wire with
electricity, when starting the car, this
wire will cut off power suddenly at
the moment.
Once the car is started, both white
& brown wire are with electricity.
4.If there is only one ignition wire in
your ignition wire harness, connect
it with the white ignition 1 wire, no
need to connect the brown ignition
2 wire
5.If there are 2 ACC wire in your
ignition harness, connect both ACC
wires with orange wire in EC002
6.If there are 2 starter wires in your
ignition harness, connect both
starter wire with yellow wire in
EC002.
7. If your car is newer cars that no
ACC( only ON & OFF), connect the
orange ACC( Accessory) wire and
white ignition 1 wire in EC002 wire
harness with ignition 1 wire in your
vehicle.
Note 9:
If the alarm is equip with shock
sensor, then connect with shock
sensor. If so, there will be no GWR
wire in the kit and you can use the
SPST relay to have a GWR wire.
Method is as right diagram:
You can also use a SPDT relay to
have a GWR wire and wiring
method is the same but no need to
connect 87a on SPDT relay.
below method:
Method 1: Cut off the car factory chip
immobilizer wire into 2 parts, each end
connect with the white & yellow wire
respectively;
Method 2: If there is GWR (-) wire, connect
the G R(-) wire with white wire and
connect yellow wire with ground(GND)
Method 3：If there is key sense wire which
require either ground (-) or positive (+) wire,
connect the key sense wire with white wire
and connect the yellow wire with ground (-)
or +12V respectively.
W
connect with GWR(-) from bypass module
connect with
Ec002 ACC or ignition1
(ACC is recommend)
connect with chassis ground(GND)
Black wire: Ground (GND)
See note 15
(-)
White wire: GPS
Blue wire:
fuel pump wire (+) (see note 11)
Green/Black wire: trunk release see note 13, 14) (
Green wire: Output of trunk/
trunk motor (see note 13, 14)
Purple wire:
trunk positive/
negative selection
Programming
switch
Brown wire: turn signal light (+)
Brown wire: turn signal light (+)
Yellow/black wire
White/black wire
Orange/black wire
Yellow wire
Pink wire: output of horn (-300mA) See Note 17
Orange wire
Green wire
GPS terminal
(optional, Default is
without GPS, only
connect when there is
with GPS tracker)
Orange wire:
foot brake wire (+)
Blue/black door trigger wire(-)
(see note 10, 18)
(see note 12)
Password keypad
If you do not use touch
password entry function,
then no need to connect
this wire.
+12V
The blue/black door trigger wire
default is negative (-), which can
be set by jumper to be positive (+)
(see note 10,18)
Door lamp
Door
switch
+12V
See central
door locking
wire connection
Footbrake
GPS terminal
(optional, Default is
without GPS, only
connect when there
is with GPS tracker)
White wire ( )See Note 16
Black wire: Ground (GND)
See note 15
(-)
High frequency antenna Red 3-pin antenna( )
Low frequency PKE antenna Black 3-pin antenna( )
Low frequency PKE antenna (Black 3-pin antenna)
1 2
3
4
5
6
1
2 3 4 5
6
O
N
$
D
I
P
white, 4pin
white, 6pin
white, 20Pin
black, 4 pin
IMPORTANT TIPS:
1.Connect the black chassis ground wires first when making wire connection to avoid damage on the device
2.Once you finish all wire connection, test the function first and remember to use the electrical tapes or strips to
tighten all the wire connection to avoid any poor connection between the control module & wire harness.
Red, +12V wire for GPS module(optional,
default is without GPS module, only connect
when there is with GPS module)
-32-
© EASYGUARD Electronics. All right reserved.
-31-
© EASYGUARD Electronics. All right reserved.