User's Manual

Arm/Panic mode
Disarm
Start button/
trunk release
Important: The PKE feature default is turn on. When PKE feature is turn on, press lock button once
will turn off the PKE function and lock the car door at the same time. If user want to turn on PKE feature
again, just press unlock button once will turn on the PKE function, at the same time the car door is
unlocked.
1.Mute alarm: Turn off the car, lock/arm the alarm, keep pressing lock button for 3 seconds, turn signal lights
flashes twice, siren beeps twice, the alarm is enter into mute alarm function. When the alarm is in mute alarm
status, the siren will not beep when lock or unlock the car door.
2.Audible alarm (exit mute alarm): Turn off the car, lock/arm the alarm, keep pressing lock button for 3
seconds, turn signal lights flashes once, siren beeps once, the alarm is enter into audible alarm function.
3.Valet mode(Car washing mode): Started the car, stepping on foot brake pedal, keep pressing lock &
unlock button on key fob at the same time for 5 seconds, siren beeps 5 times and turn signal light flashes 5
times. The alarm is enter into valet mode (car washing mode) & turn off PKE function. When the alarm is in valet
mode, user can’t use remote engine start function.
4.Exit valet mode (car washing mode): Started the car, stepping on foot brake pedal, keep pressing lock &
unlock button on the key fob at the same time for 5 seconds, siren beeps 3 times and turn signal light
flashes 3 times. The alarm is exit valet mode (car washing mode) & turn on PKE function.
Other common used function:
1.Lock/Arm: press lock button once(turn off PKE
function)
2.Unlock/disarm: press unlock button once(turn on
PKE function)
3.Remote engine start: In arm status, keep pressing
the start button for around 3 seconds. Please keep at
least 8 meters away from the vehicle when use
remote engine start function.
4.Remote engine cut off: Once the vehicle is remote
started, keep pressing the start button for around 3
seconds will remote cut off the engine. Please keep at
least 8 meters away from the vehicle when use
remote engine cut off function.
5.Panic mode: in arm status, press lock button once
6.Remote trunk release: Continue to press start button
twice.
Please refer to above key fob button introduction to operate related function accordingly.
The remote control is an intelligent electronic device with inductive function. Please follow the following
instruction to avoid damage.
1.Don’t put the remote control in an environment with damp, sunshine or high temperature.
2.Don’t dismantle the remote control. The users can’t inspect the components inside.
3.To avoid strong strike or heavy crash.
4.Don’t put the remote control together with the metal keys or avoid damage or signal shielding.
5.Don’t put the remote control with cell phone or other products will emit strong signal to avoid the signal
interference.
6.When one remote control is using, the other remote control will be in sleep mode to save power. If you want to
activate it, press any button on it will activate it.
If the PKE function of the smart remote control is not working well or the LED indicator is dim or not lit, it’s
probably due to the battery is low. If so, please check the battery of the remote control and replace it with a new
one.
5. Attention: If there is chip immobilizer in
factory original key or remote control, need
to take out the chip immobilizer and hide
it inside or near the ignition cylinder. Please
refer to installation for chip immobilizer. If you
can’t find the chip by yourself. Just hide the
original key or remote control in or near the
ignition cylinder. (Please remember to take
out the battery of the remote if you do so).
6 Everything finish like
the picture:
. 7. If you don’t want to cut the key
for releasing the steering lock, you
can make a hole in the car which
near the steering and install the
push start button .Like the picture,
but it will not convenient for you
as you need to use the original key
to release the steering lock every
time you start the car.
8. Un-plug the
factory ignition
wire harness to
avoid which
consume the
vehicle battery
power.
-20-
© EASYGUARD Electronics. All right reserved.
1. Please check whether there is steering lock in your vehicle or not, if yes, follow with the next step.
2. Copy a key blade with your factory original key blade and match them so that the copied key blade can start
the car.
3. When finish matched, put the copied key blade into the ignition cylinder of car, like this picture,
Manual for releasing the steering lock:
turn the key to
“ON” position.
Inside the lock
So that the steering lock can be turn round. Then cut and keep 1mm
length of the copied key outside of the lock. See the picture:
Cut the key
Outside the lock
Inside the lock
Cut & keep 1mm outside
Stick on
the lock
4. Stick the push start button on the lock. .
(That is the reason for cutting the key.)
-19-
© EASYGUARD Electronics. All right reserved.