Operation Manual

ManualsBrandsEasyAlarm ManualsBackupCONTROL

5. CONFIGURATION OF THE ALARM REGISTERS

5.1 Sensor-1 monitoring

5.1.1 Sensor-1 as alarm contact

EasyAlarm

auto-detects a Plug&Protect-sensor and starts its monitoring if the system is armed. You can define the

behaviour for sensor-1 as following:

Example: A normally closed contact shall trigger an un-delayed alarm with a hands-free-connection independent from

position of the selection switch.

1. Slide function switch to PROG

2. Enter sequence *. 9. 3. 1. 7 5 6 #. #.. .

 Current register (bit 7 -> bit 0) will be announced followed by “to modify press *., to stop press #.“

3. If you want to keep current value proceed with step 6. Otherwise start modifying register by pressing *..

4. Enter sequence 0. 0. 1. 0 0 0. 1. 1. .

R-Siren Entry-Delay Connect. mode Sensor on.. Type

0: off 0:off 0: Listening-in I / II / III 00: inactive

1: on 1:on 1: Hands-free 0 0 0 01: Normally open contact

0: enabled 10: Plug&Protect (auto-detected at power-on)

1: disabled input-2 is open => Normally open monitoring

input-2 is closed => Normally closed monitoring

5. Press key #. . 11: Normally closed contact

 The new register (bit 7 -> bit 0) will be announced

6. Slide function switch to OFF

5.1.2 Sensor-1 for presence verification

You can also use sensor-1 to monitor missing activity (i.e. no motion detected within a certain period) => Alarm message:

„Emergency call due to sensor-1“. Therefore you have to activate time-out as below.

5.1.2.1 How to program presence verification time-out

Time-out for presence verification is factory set to 24h. If there is no activation within this period, an alarm is triggered

after a pre warning period of 10 minutes (this period is indicated with a periodical loud beep tone).

1. Shift function switch to PROG

2. Enter *. 9. 7. 1. 3 6 7 #. #. .

 Current register value <n> will be announced followed by “to modify press *., to stop press #.“

3. If you want to keep current value proceed with step 4. Otherwise modify register with *. New value <n> #..

 The new register value <n> will be announced

4. Shift function switch to OFF

<n> Explanation

0 Presence verification is switched off (=Factory setting)

6..255 Time-out in steps of 10 min. (min. 60min, max. 42.5h) => For example: n=144 (144*10min = 24 h)

5.1.3 Sensor-1 as entry-detector (Gong function)

A sensor-1 activity can also be signalled locally (Gong-function) according to the following procedure:

Example: Sensor-1 shall greet an incoming person with the pre-recorded individual message only on position I.

1. Slide function switch to PROG

2. Enter sequence *. 9. 3. 1. 7 3 1 #. #...

 Current register (bit 7 -> bit 0) will be announced followed by “to modify press *., to stop press #.“

3. If you want to keep current value proceed with step 6. Otherwise start modifying register by pressing *..

4. Enter sequence 0. 0. 0. 0 1 1. 1. 0. .

Unused Gong on.. Gong-type

000: I / II / III 00: Gong

0 1 1 01: --

0: enabled 10: Individual message

1: disabled 11: Beep loud

5. Press key #. .

 The new register (bit 7 -> bit 0) will be announced

6. Slide function switch to OFF

Factory default for sensor

1 monitoring

00 0 000 10, => un-delayed alarm in listening-in

connection only on all positions I/II/III

=> connector type: auto-type (plug&protect)

Factory default for gong

function sensor

000 111 00

Note:

 If you do not want to

trigger an alarm on

position I you have to

disable alarm according to

section 5.1.1