User Manual Spend a little Live a lot. OPED I N VEL DE nse om my ha NY RMA GE MANUA L MEN’S SHAVER BATTERY/MAINS c o n t ro l.
QR codes take you where you want to go quickly and easily Whether you require product information, spare parts or accessories, details on warranties or aftersales services, or if you want to watch a product demonstration video, our QR codes will take you there in no time at all. What is a QR code? A QR code (QR = Quick Response) is a type of matrix that can be read with a smartphone camera and that contains a link to a website or contact details, for example.
Overview........................................................................... 4 Use...................................................................................... 5 Scope of delivery/device parts........................................ 6 General information......................................................... 7 Reading and storing the instruction manual..................7 Explanation of symbols.......................................................7 Safety...................................
GB IRE A 10 1 11 2 3 9 8 4 5 7 90 12 13 14 6 B C 90 6 18 17 D 19 15 16
GB E F G H I J K L IRE 5 20
GB IRE Scope of delivery/device parts Protective cap with 3-day beard trimming function 11 Storage bag 12 Mains cord 2 Shaving foil unit 13 AC adapter plug 3 Shaver blades, 2x 14 5 V plug 4 Small release button, 2x Electronic On/Off switch (with built-in travel lock and turbo function) 15 Turbo symbol 5 16 Mains symbol 6 Female plug 17 Lock symbol 7 Battery capacitance in % 18 Tap symbol 8 Large release button 19 Trimmer 9 Shaver head (shaver head frame with shaving fo
General information IRE GB General information Reading and storing the instruction manual This instruction manual accompanies this men’s shaver battery/mains. It contains important information on start-up and handling. For improved readability, the men’s shaver battery/ mains will be referred to only as the “shaver” below. Before using the shaver, read the instruction manual carefully. This particularly applies for the safety notes.
GB IRE General information CAUTION! CAUTION! This signal word designates a hazard with low risk that, if not avoided, may result in minor or moderate injury. NOTICE! NOTICE! This signal word warns against potential damages to property. This symbol provides you with useful additional information on use. Declaration of conformity (see chapter “Declaration of conformity”): Products marked with this symbol meet all applicable Community regulations for the European Economic Area.
General information IRE GB This symbol identifies electrical devices that belong to the protection class III (shaver). This symbol indicates the polarity of the current on the 5 V plug. Devices marked with this symbol are only suitable for household use (dry indoor rooms). This symbol identifies intrinsically safe transformers (with a fuse and thermo protection). The shaver is suitable for being cleaned under running water.
GB IRE Safety Safety Proper use The shaver is designed exclusively for dry and wet shaving of the face, but also for trimming beards. The shaver is only suitable for private use and not suitable for commercial purposes. The shaver may only be used in indoor spaces. Only use the shaver as described in this instruction manual. Any other use is considered improper and may result in damage to property. The manufacturer or vendor accepts no liability for damage caused by improper or incorrect use.
Safety IRE GB −− Only use the shaver with the enclosed mains adapter. The shaver requires safety extra-low voltage (SELV) with the values specified in the chapter “Technical data”. −− Only connect the mains adapter to an easily accessible socket so that you can quickly disconnect it from the mains in case of a failure. −− If the mains cord, the mains adapter or the shaver exhibit visible damages or are defective, do not use them further.
GB IRE Safety −− Keep the shaver, the mains cord and mains plug away from water and other liquids, open flames and hot surfaces. −− Never touch the mains plug with damp hands. −− Never pull the mains plug out of the socket by the mains cord; instead, always do so by taking hold of the mains plug. −− Never use the mains cord as a carrying strap. −− Lay the mains cord so that it does not pose a tripping hazard. −− Do not kink the mains cord and do not lay it over sharp edges.
Safety IRE GB −− Always turn the shaver off and pull the mains plug out of the socket • when you are not using the shaver, • when you are cleaning the shaver, • in the event of a fault or • in the event of a storm. WARNING! Risk of explosion and fire! Handling the rechargeable battery improperly may lead to an explosion or fire resulting in injury and damage to property. −− Protect the rechargeable battery against mechanical damage.
GB IRE Safety WARNING! Danger for children and persons with impaired physical, sensory or mental capacities (e.g. partially disabled persons, older persons with reduced physical and mental capacities) or lack of experience and knowledge (e.g. older children).
Safety IRE GB CAUTION! Risk of injury due to sharp edges and blades! If you use the shaver with a damaged shaver head, without a shaver head or if you push down on the shaving foils, you could cut yourself on the sharp edges or blades. −− Do not push the shaving foils in with your fingers. −− Do not use the shaver if the shaver head, the integrated shaving foils or the trimmer are damaged. −− Do not use the shaver if the shaver head is not firmly mounted.
GB IRE First use First use Checking the shaver and product contents NOTICE! Risk of damage! If you are not cautious when opening the packaging with a sharp knife or other pointy object, you may damage the shaver. −− Be careful when opening. 1. Carefully take the shaver, the individual parts and the accessories out of the packaging. 2. Check to make sure that the delivery is complete (see fig. A). 3. Check whether the shaver, the individual parts or the accessories exhibit damage. 4.
First use IRE GB Displaying the status The shaver has an indicator – the mains symbol 16 – that supplies information about the power supply or the charge level of the rechargeable battery (see fig. C): Symbol Meaning Battery, illuminated in blue (00 – 100 %) Indicates the battery charge level in 10 % increments. Turbo, flashing in blue The turbo function has been activated. Mains, illuminated in red The rechargeable battery is being charged. The battery charge level is shown in %.
GB IRE Handling Charging the rechargeable battery NOTICE! The rechargeable battery takes approx. 90 minutes to charge fully. However, you can also use the shaver in mains operation without charging the rechargeable battery. 1. Insert the 5 V plug 14 in the female plug 6 on the bottom of the shaver (see fig. A and B). 2. Connect the AC adapter plug 13 in a properly installed socket. The mains symbol 16 on the display illuminates in red to indicate that the battery is charging. 3.
Handling IRE GB For a dry shave, follow the steps below: 1. Take the protective cap 1 off of the shaver (see fig. A). 2. Use the electronic On/Off switch 5 to switch the shaver on. 3. Use your free hand to stretch the part of your face you intend to shave. 4. While applying gentle pressure, move the shaver head 9 perpendicular to the direction of hair growth. 5. After a few strokes, use your free hand to check the results and repeat step 4 if necessary. 6. Shave as described in steps 2 – 4. 7.
GB IRE Handling 4. While applying gentle pressure, move the shaver head 9 perpendicular to the direction of hair growth. 5. After a few strokes, use your free hand to check the results and repeat step 4 if necessary. 6. Shave as described in steps 2 – 4. 7. If necessary, use the trimmer 19 as described in the chapter “Using the trimmer” (see fig. D). 8. After shaving, switch the shaver off by pushing the electronic On/Off switch twice. 9.
Handling IRE GB Using the trimmer NOTICE! Keep in mind that the trimmer always generates a straight cutting edge. If you do not want a straight cutting edge, you must hold the shaver at an angle. For hard-to-reach areas or for very precise cuts, use a comb to check the hair you intend to trim with the trimmer and the cut length. Use the trimmer as follows: 1. Move the trimmer 19 all the way out until it audibly locks into place (see fig. D). 2.
GB IRE Handling Using the turbo function NOTICE! Risk of damage! Using the turbo function for prolonged periods accelerates the wear of the shaving foils. −− Only use the turbo function for short periods and not for the entire shave. −− Oil the shaving foils regularly to reduce frictional resistance. NOTICE! After switching the shaver off and back on, the shaver will be in standard mode again. This shaver has a turbo function. Activating it increases the shaver speed.
Handling IRE GB 4. Push and hold the electronic On/Off switch again for approx. 1.5 seconds to deactivate the turbo function again. The shaver will also be switched off when deactivating the turbo function. Using the travel guard The shaver is equipped with a travel guard that prevents the shaver from accidentally activating. Activating the travel guard −− Hold the electronic On/Off switch 5 down for more than 3 seconds (see fig. A).
GB IRE Cleaning and care Cleaning and care NOTICE! Risk of short circuit! Water that has penetrated the mains cord or the mains adapter may cause a short circuit. −− Never immerse the mains adapter or the 5 V plug in water. NOTICE! Risk of damage! Improperly cleaning the shaver may damage its surface, the shaving foils and the shaver blade. −− Do not use any aggressive cleaners, brushes with metal or nylon bristles, sharp or metallic cleaning utensils such as knives, hard scrapers and the like.
Cleaning and care IRE GB 4. Push the small release buttons 4 to release the shaving foil unit 2 . 5. Pull the shaving foil unit up and off (see fig. K). 6. Knock the shaving foil unit out gently over a sink to remove stubble. 7. Place the shaving foil unit on a suitable base. 8. Depress the large release button 8 to open the shaver head 9 (see fig. A and E). 9. With the shaver head open, use the electronic On/Off switch 5 to switch the shaver on for approx.
GB IRE Cleaning and care 4. Push the small release buttons 4 to release the shaving foil unit 2 . 5. Pull the shaving foil unit up and off (see fig. K). 6. Wash the shaving foil unit thoroughly under warm running water on the inside and outside (see fig. G). 7. Place the shaving foil unit on a suitable base. 8. Depress the large release button 8 to open the shaver head 9 (see fig. A and E). 9. Thoroughly rinse off the top part of the shaver and the shaver blades 3 under warm running water (see fig.
Cleaning and care IRE GB Weekly cleaning It is recommended that you perform a more thorough cleaning once a week, both for dry and wet shaving. To do so, proceed as follows: 1. Use the electronic On/Off switch 5 to switch the shaver off (see fig. A). 2. Pull the 5 V plug 14 out of the shaver (see fig. A and B). 3. Hold the shaver over the sink. 4. Push the small release buttons 4 to release the shaving foil unit 2 . 5. Pull the shaving foil unit up and off (see fig. A and K). 6.
GB IRE Cleaning and care 12. Thoroughly wash the shaver head under warm running water from the inside and outside (see fig. G). 13. Depress the large release button 8 to open the shaver head 9 (see fig. A and E). 14. Thoroughly rinse off the shaver blades under warm running water (see fig. H). 15. Use the electronic On/Off switch to switch the shaver on with the shaver head opened for approx. 5 – 10 seconds in order to discharge any drops of water off of the shaver blades. 16.
Cleaning and care IRE GB User maintenance for the shaving foils To maintain the performance of your shaver and increase the service life of the shaving foils, you should perform user maintenance on the shaving foils every week, but no less than once a month as follows: 1. Put a drop of fine, non-resinous household oil on the tip of your finger. 2. Distribute the oil evenly on the shaving foils. 3. Without applying pressure, dab the shaving foils with a soft, lint-free cloth or paper towel.
GB IRE Technical data 5. Gently push the shaving foil unit on the frame of the shaving foil unit onto the shaver until the locking mechanism audibly engages (see fig. L). 6. Oil the shaving foils as described in the chapter “User maintenance for the shaving foils”. 7. Place the protective cap 1 on the shaver (see fig. A). Your shaver is now ready for use again. Replacing the shaver blades We recommend replacing the shaver blades no later than after 12 months of daily use.
Technical data Power supply: Rechargeable battery: Charging time: Operating time: Motor: Protection class mains adapter: Protection class shaver: IP code mains adapter: IP code shaver: Cable length: Cutting blades: Shaving foils: Dimensions (W x D x H): Weight (including accessories): AFTER SALES SUPPORT GB IRE IRE GB Mains adapter Input 100 – 240 V/AC, 50 – 60 Hz, max. 0.2 A Output 5 V/DC, 900 mA 1 x Li-Ion 800 mAh Protected against overloading and deep discharge 90 min. max. 95 min 3.
GB IRE Declaration of conformity Declaration of conformity The EU declaration of conformity can be requested from the address specified on the warranty card (at the end of this instruction manual). Disposal Disposing of the packaging Dispose of the packaging separated into single type materials. Dispose of cardboard and carton as waste paper and foils via the recyclable material collection service. Dispose of the packaging in accordance with the applicable laws and regulations for your country.
Disposal IRE GB Disposing of old devices (Applicable in the European Union and other European states with systems for the separate collection of reusable waste materials) Old devices must not be disposed of with household waste! If the shaver is no longer operational, every consumer is required by law to dispose of used devices separately from household waste, e.g. at a collection point run by the communal authority or borough.
GB 34 IRE GB IRE 00800 36463600 www.aquarius-service.
IRE GB WARRANTY CARD MEN’S SHAVER BATTERY/MAINS Your details: Name Address E-mail Date of purchase * * We recommend you keep the receipt with this warranty card. Location of purchase Description of malfunction: If after contacting the manufacturer you are requested to return the faulty product please return the completed warranty card together with it. Docdata Fashion Services GmbH Retourenannahme Aquarius Amshamerstr. 2 D- 84385 Egglham GERMANY E-mail: aquarius-service@docdata-eb.
GB IRE Warranty conditions Dear Customer, The ALDI warranty offers you extensive benefits. Warranty period: 3 years from date of purchase. 6 months for wear parts and consumables under normal and proper conditions of use (e.g. rechargeable batteries). Costs: Free repair/exchange. No transport costs. Hotline: Toll free hotline. ADVICE: Please contact our service hotline by phone, e-mail or fax before sending in the device. This allows us to provide support in the event of possible operator errors.
IRE GB • Accident or unanticipated events (e.g. lightning, water, fire). • Improper use or transport. • Disregard of the safety and maintenance instructions. • Other improper treatment or modification. After the expiry of the warranty period, you still have the possibility to have your product repaired at your own expense. If the repair or the estimate of costs is not free of charge you will be informed accordingly in advance. This warranty does not affect your statutory rights.
Spend a little Live a lot. Great care has gone into the manufacture of this product and it should therefore provide you with years of good service when used properly. In the event of product failure within its intended use over the course of the first 3 years after date of purchase, we will remedy the problem as quickly as possible once it has been brought to our attention.
