User Manual

D. EXEMPLE Nº 1 — EXEMPLE D'ÉVALUATION TYPIQUE
Prenonsunesectiondutoit(VoirFigureB-2àlapage43)àtraiterquia:
• 32piedsdetoiture
• unavant-toitde12poucesavecunegouttière
• 1noue(30piedsdepourtour)
• 1noue
• 2descentespluviales(chaquelongueurde10pieds)
Dans le Tableau B-2, le multiplicateur pour un toit avec gouttière et un avant-toit de 12 pouces est 4.
À l’aide du Tableau B-1, la longueur de câble nécessaire = (32 x 4) + (1 x 30) + (1 x 6) + (2 x 10 x 2) = 204
Àl’aideduTableauB-3,vousdevrezchoisirADKS-1000(200piedsdecâble).Vousdevrezchoisirlecâblelepluspetitparcequeladifférenceentre
la longueur de câble et votre calcul est moins de 5 pieds.
E. EXEMPLE Nº 2 — EXEMPLE D'ÉVALUATION DE SECTION SPÉCIFIQUE DU TOIT
Cet exemple montre comment évaluer la longueur de câble nécessaire pour une section du toit qui pose un problème limité. Pour ce toit, il est préférable
detraiterseulementlasectionquiposeproblèmeau-dessousdupuitsdelumière(VoirFigureB-3àlapage45).
Cette section du toit a :
• 1descentepluviale(l0piedsdelong)
• 1puitsdelumière(ladistanceentrelefonddupuitsdelumièreetlaborduredutoitest12,5piedsetlalargeurdesbancsdeglacequiseforment
au-dessous du puits de lumière est d’environ 6 pieds)
• 1gouttière
Dans le Tableau B-6, le multiplicateur pour la section spécifique du toit avec gouttière est 2,6.
À l’aide du Tableau B-5, la longueur de câble nécessaire = (1 x 10 x 2) + (12,5 x 6 x 2,6) = 215
Dans le Tableau B-3, vous devrez choisir ADKS-1200 (240 pieds de câble) pour assurer une couverture complète.
Note : Si vous traitez seulement une section spécifique du toit et la section qui pose problème est à une grande distance de la descente pluviale, il est
préférabled’ajouterunelongueursupplémentaireàvotreévaluationpourtenircompteducâbledanslagouttière.
46 Guide de l’utilisateur modèle ADKS
ADKS Owner’s Manual 23
D. EXAMPLE #1 – EXAMPLE OF TYPICAL ESTIMATION
Consider a roof section (See Figure B-2 on page 20) that you want to treat that has:
• 32 feet of roof
• an overhang of 12 inches with a gutter
• 1 dormer (30 feet around)
• 1 valley
• 2 downspouts (each 10 feet long)
From Table B-2, the multiplier for a roof with a gutter and an over hang of 12 inches is 4.
Using Table B-1, the cable length needed = (32 x 4) + (1 x 30) + (1 x 6) + (2 x 10 x 2 ) = 204
Using Table B-3, you would select the ADKS-1000 (200 feet of cable). You would select the smaller cable because the difference between the cable
length and your calculation is less than 5 feet.
E. EXAMPLE #2 – EXAMPLE OF SPECIAL ROOF AREA ESTIMATION
Thisexampleshowshowtoestimatethecablelengthneededforalimitedproblemroofarea–askylight(seeFigureB-3onpage22).Forthis
roof, you would like to treat only the problem area underneath the skylight.
This roof section has:
• 1 downspout (l0 feet long)
• 1 skylight (the distance from the bottom of the skylight to the roof edge is 12.5 feet, and the width of the ice dams that form beneath the
skylight is about 6 feet)
• 1 gutter
From Table B-6, the special roof area multiplier for a roof with a gutter is 2.6.
Using Table B-5, the cable length needed = (1 x 10 x 2 ) + (12.5 x 6 x 2.6) = 215
From Table B-3, you would select the ADKS-1200 (240 feet of cable) to ensure complete coverage.
Note: If you are only treating one special roof area and the problem area is a significant distance from the downspout, you may wish to add extra
cable to your estimation to account for the cable in the gutter.
ENG
FRA