EN NO SV DA FI DE NL FR IT ES User guide / Installation guide Brukerveiledning / Installasjonsveiledning Användarmanual / Installationsguide Brugervejledning / Installationsmanual Käyttöohje / Asennusohje Benutzeranleitung / Installationsanleitung Gebruikershandleiding / Installatiehandleiding Mode d'emploi / Instructions d'installation Manuale utente / Guida d'installazione Guía de usuario / Guía de instalación Easee Equalizer
English Table of contents Norsk 10 Introduction Svenska 18 Introduction 3 Dansk 26 Product overview 4 Suomi 34 Safety instructions 4 Deutsch 42 Technical specifications 5 Nederlands 50 Français 58 Installation Italiano 66 Customer setup 6 Español 74 Installer setup 7 Daily use and operation LED colours meaning 8 Practical details 9 IMPORTANT: Read carefully before use. Keep for future reference. When passing on the product, ensure this guide is also passed on.
Introduction This manual concerns the two versions of the product: Easee Equalizer (E02-EQP) and Easee Equalizer HAN (E02-EQ). All instructions apply to both versions, unless specified otherwise. Intended use This product is intended for optimizing the power consumption by performing an automatic load balancing between the Easee Charging Robot(s) and the building. It is used to avoid overload and power interruptions while the electric vehicle (EV) is being charged. cases needs to be activated.
Product overview Safety instructions Equalizer Read the entire manual carefully before installing and operating the product. Observe the following instructions: Magnetic backside — Do not use the product if it is damaged or does not function properly. — Always have any repair work carried out by an authorised electrician and in accordance with local requirements. — This product is intended for indoor use in dry locations only.
Technical specifications Max transmitted power Radio: 25 mW at 863–870 MHz. WiFi: 50 mW at 2.4–2.472 GHz. General Product (mm): H: 110 x W: 110 x D: 27.
Installation Customer setup Follow these steps if you are a private customer installing the Equalizer in your own household. 1 Activation 2 Download 3 Setup In Scandinavia, the communication port on the smart meter is most likely not activated. Contact your utility company to open the HAN port for use with the Equalizer. If you are not in Scandinavia, skip to step 2. Scan the QR code to download the Easee App and create a free account.
Installation Installer setup Follow these steps if you are an installer and use the Installer App to configure the Equalizer in large commercial installations or private households. 1 Download 2 Setup 3 Connect Scan the QR code to download the Installer App and create a free account. Add the Equalizer to a new or existing charging site using the Installer App and follow the on-screen installation guide to set it up. Connect the Equalizer to the smart meter using the provided cable.
LED colours meaning 3'' Hold the Easee logo for 3 seconds to check connectivity.
Practical details Warranty The device is free from material defects and is in accordance with laws and regulations for consumer protection in the country where the product is purchased. All correctly installed Easee hardware is covered by our 3 years* limited warranty. *Some countries may have extended warranty. Standards Hereby, Easee AS declares that the radio equipment types Easee Equalizer (E02-EQP) and Easee Equalizer HAN (E02-EQ) are in compliance with Directive 2014/53/EU.
THIS DOCUMENT CONTAINS INFORMATION THAT IS SUBJECT TO CHANGE WITHOUT NOTICE. The latest version of this publication can be downloaded at http://easee.support No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including, but not limited to, copying, recording, retrieving data, or computer networks without the written permission of Easee AS. Easee and all other Easee product names and slogans are trademarks or registered trademarks of Easee AS.
Easee AS Grenseveien 19 4313 Sandnes, Norway .easee.
