User Manual

MV-2505-02--2022
.
eeese-air-care.com © All rights reserved eeese air care aps
41
UK
3
When used regularly , the filter may become clogged with dust and particles. Therefore the filter should
be cleaned at least every two weeks. Follow these steps:
1. Switch the device off and remove the plug from the socket before
cleaning.
2. Clean the housing with soft, dry cloth. If the device is extremely dirty,
use a mild cleaning agent. Wipe the dehumidifier with a slightly damp
cloth. Never spray the device with water.
3. Remove the filter, clean the filter with a vacuum cleaner or soapy
water no hotter than 40℃.
4. Rinse and dry the filter completely before installing back to the
device.
8
Cleaning
1
Product Instructions
Safety Instructions
The dehumidifier is used to remove excessive moisture from the air. The resulting reduction in relative
humidity protects buildings and their contents from the adverse effects of excess humidity.
The environmentally friendly R290 is used as the refrigerant. R290 has no damaging influence on the
ozone layer (ODP), a negligible greenhouse effect (GWP) and is available worldwide. Because of its
efficient energy properties, R290 is highly suitable as a coolant for this application. Special precautions
must be taken into consideration due to the coolant's high flammability.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
The unit is designed only for use with R-290(propane) gas as the designated refrigerant.
THE REFRIGERANT LOOP IS SEALED. ONLY A QUALIFIED TECHNICIAN SHOULD ATTEMPT
TO SERVICE!
Do not discharge the refrigerant into the atmosphere.
R-290 (propane) is flammable and heavier than air.
It collects first in low areas but can be circulated by the fans.
If propane gas is present or even suspected, do not allow untrained personnel to attempt to find the
cause.
The propane gas used in the unit has no odor.
The lack of smell does not indicate a lack of escaped gas.
If a leak is detected, immediately evacuate all persons from the store, ventilate the room and contact
the local fire department to advise them that a propane leak has occurred.
Do not let any persons back into the store until the qualified service technician has arrived and that
technician advises that it is safe to return to the store.
No open flames, cigarettes or other possible sources of ignition should be used inside or in the vicinity
of the units.
Component parts are designed for propane and non-incentive and non-sparking. Component parts
shall only be replaced with identical repair parts.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
The appliance shall be disconnected from its power source during maintenance.
Ensure the unit is far away from fire, inflammable, or explosive objects.
Do not use means to accelerate the defrosting process or to clean, other than those recommended
by the manufacture.
Remove the Air Inlet Grille, clean the lter with a vacuum
cleaner or soapy water no hotter than 40°C.
4
Rinse and dry the lter completely before installing back to
the device.
7. Storage
If the dehumidier will not be used for a long period of time, take the following steps:
1. Remove the plug from the socket and empty the tank, make sure the tank and the
dehumidier is completely dry. This may take a couple of days.
2. Clean the air lter.
3. Check the dehumidier for perfect condition to ensure a safe use of it after a long
period of storage.
4. Pack the device with the suitable packaging.
5. Store the dehumidier in a dust-free location, and out of direct sunlight. Preferably
covered with a sheet of plastic.
8. Display Error Codes
Please contact your local distributor if any of the error codes below appears.
Code Error Display What is happening
E1
Temperature sensor
error
Flash every 30
seconds
Device still dehumidies but is
in defrost mode only.
E2 Humidity sensor error
Flash every 30
seconds
Device still dehumidies but
is in continuous dehumidifying
mode only.
L3
Air inlet temperature
is too
high >42ºC
Slowly ash L3
Compressor stop working, fan
works at low fan speed. 10mins
later, if the temperature decrea-
se to below 40 machine will
work normally.