SRT ROTOTILLER OPERATORS MANUAL 7055C BRIGGS & stratton 4-cycle 206cc 8.50 ft-lbs gross torque ARDI SA M .com GetEarthquake.com OMSRT Rev. 10/06/10 © 2010 Ardisam, Inc. All Rights Reserved.
OPERATor INSTRUCTIONS and parts SRT Model 7055C INTRODUCTION Thank You . . . for purchasing an Earthquake® forward rotating rear-tine rototiller from Ardisam, Inc. We have worked to ensure that this rear-tine rototiller meets high standards for usability and durability. With proper care, your rototiller will provide many years of service. Please take the time to read this manual carefully to learn how to correctly operate and maintain your rototiller.
OPERATor INSTRUCTIONS and parts SRT Model 7055C SAFETY ! DANGER OWNER’S RESPONSIBILITY Accurate assembly and safe and effective use of the rototiller is the owner’s responsibility. • Read and follow all safety instructions. • Carefully follow all assembly instructions. • Maintain the tiller according to directions and schedule included in this Earthquake operator’s manual. • Ensure that anyone who uses the tiller is familiar with all controls and safety precautions.
OPERATor INSTRUCTIONS and parts SRT Model 7055C c. Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors. IMPORTANT The right and left sides of your rototiller are determined from the operating position as you face the direction of forward travel. Engine is shipped from factory without oil. You must add engine oil before starting engine. d. Replace gasoline cap securely and clean up spilled fuel before restarting.
OPERATor INSTRUCTIONS and parts SRT Model 7055C SAFETY DECALS This rototiller unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
OPERATor INSTRUCTIONS and parts SRT Model 7055C Unpacking and Assembly Your rototiller comes fully assembled except for a few parts. The following instructions will help you unpack your tiller and assemble and adjust your tiller’s depth regulator lever, cable tension and handlebar height. You will need 2- 9/16” wrenches. Unpack tiller 1. Open top of carton and remove handlebar assembly. 2. Find parts packet.
OPERATor INSTRUCTIONS and parts SRT Model 7055C Features forward drive safety control lever reverse drive safety control lever forward & reverse cable bumper guard depth regulator lever detent pin belt guard wheel lock pin recoil start serial number plate 800-345-6007 Page GetEarthquake.
OPERATor INSTRUCTIONS and parts SRT Model 7055C OperatioN ! CAUTION PRE-START INSPECTIOn 1. Make sure all safety guards are in place and all nuts and bolts are secure. 2. Check oil level in engine crankcase. See your engine manual for procedure and specifications. 3. Inspect air cleaner for cleanliness. See your engine manual for procedure. 4. Check the fuel supply. Fill the fuel tank no closer than 1 inch from top of tank to provide space for expansion. See your engine manual for fuel recommendations.
OPERATor INSTRUCTIONS and parts SRT Model 7055C Idle Speed Use the “low” position on the throttle lever to reduce stress on the engine when tilling is not being performed. Lowering the engine speed to “idle” will help extend the life of the motor, as well as conserve fuel and reduce the noise level of the equipment. Operating Speed For normal tilling, set the throttle lever to “fast”. SHUTTING DOWN To stop the engine at any time, move throttle control or ON/OFF switch to the off position.
OPERATor INSTRUCTIONS and parts SRT Model 7055C Drive SAFETY Control LeverS ! CAUTION FORWARD LEVER Engages wheels and tines into forward. Pulling the drive safety control lever labeled (FORWARD) toward the handlebar engages the wheels and tines. Releasing the lever stops the wheels and tines and brings the tiller to a complete stop. forward lever engaged Do not operate both “FORWARD” and “REVERSE” drive safety control levers at the same time.
OPERATor INSTRUCTIONS and parts SRT Model 7055C Wheel Lock pins ! WARNING Place wheels in tilling position. 1. Remove lock pin. Align hole in axle with hole in wheel hub. (SEE FIGURE 2) 2. Insert lock pin through holes, fold lock pin ring to secure pin to axle. 3. Firmly lock wheel and axle together before tilling. 4. Repeat for other wheel. Never start engine or operate tiller with wheels in free-wheel position.
OPERATor INSTRUCTIONS and parts SRT Model 7055C DEPTH REGULATOR LEVER Tilling depth is controlled by the height of the depth regulator lever. To adjust tilling depth. (SEE FIGURE 4) 1. Remove detent pin. 2. Raise the depth regulator lever to position tines at chosen tilling depth. 3. Align hole in depth regulator lever with hole in depth regulator bracket and replace detent pin. Depth Regulator Lever Down = Shallower tilling.
OPERATor INSTRUCTIONS and parts SRT Model 7055C Tilling Tips The key to successful tilling is to begin with a shallow cut on the first pass, and then work an inch or two deeper on each successive pass. • Tilling depth will vary with ground conditions. • When beginning to till in unbroken ground or in extremely hard soil, set the detent pin in the highest hole of the drag stake (follow instructions under Tilling section). This will allow for shallow tilling.
OPERATor INSTRUCTIONS and parts SRT Model 7055C MAINTENANCE MAINTENANCE SCHEDULE Your rototiller has been designed and produced by the industry’s leading manufacturer of outdoor power equipment to provide you with years of reliable operation. Keeping your tiller in top running condition will prolong its life, and help you obtain optimum performance. Please read this normal care schedule, and note the recommended care operating intervals to extend the life of your unit.
OPERATor INSTRUCTIONS and parts SRT Model 7055C Change Forward/Reverse Belt ! CAUTION 1. Turn off engine. Engine must be cool. Do not operate tiller before reading the engine manual provided in the parts packet. 2. Remove spark plug wire and secure from spark plug. 3. Remove belt guard. • remove the forward belt from the forward engine pulley: - gently pull the engine recoil rope to rotate the pulley. ! WARNING - with the pulley turning, force the forward belt out of the V-groove.
OPERATor INSTRUCTIONS and parts SRT Model 7055C Engine Maintenance Refer to the engine manual included in your parts packet for information on engine maintenance. Your engine manual provides detailed information and a maintenance schedule for performing the following tasks: 1. Check oil level before each use or after every 8 hours of operation. 2. Change oil after first 5-8 hours of operation. Change oil while engine is warm. Refill with new oil of recommended grade. 4.
OPERATor INSTRUCTIONS and parts SRT Model 7055C Lubrication Proper lubrication of moving mechanical parts is critical for proper care and maintenance. Oil the moving parts at 10 hour intervals using a 30 weight oil. Clean Tine Axle Shaft 1. Turn off engine. Engine must be cool. 2. Remove spark plug wire and secure from spark plug. ! WARNING Do not store tiller in an unventilated area where fuel fumes may reach flame, sparks, pilot lights or an ignited object.
OPERATor INSTRUCTIONS and parts SRT Model 7055C Troubleshooting ! WARNING Troubleshooting Guide While normal care and routine maintenance will extend the life of your rototiller, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, causes and remedies. Practice safety at all times.
OPERATor INSTRUCTIONS and parts SRT Model 7055C PROBLEM REMEDY/ACTION Belts squeal in neutral and/or reverse • Adjust forward belt guide: - turn engine off and allow muffler to cool - disconnect spark plug wire and secure from spark plug - remove belt guard - pull down on drive safety control levers - manually bend forward belt guide so there is 1/16 inch or less clearance between belt guide and belt - replace belt guard and spark plug wire Belts squeal in forward operation • Adjust tabs on the rev
OPERATor INSTRUCTIONS and parts SRT Model 7055C SRT Handlebar parts 53650(2) 53614 53632 53613 53631(2) 53612 53606(2) 53620 53607(4) 503 53629 60G56 53630(2) 53624 2104(4) 53679 90139(2) 53618(2) 90138(4) 48762(2) 2104(2) Page 20 800-345-6007 GetEarthquake.
OPERATor INSTRUCTIONS and parts SRT Model 7055C SRT Handlebar parts list PART # DESCRIPTION QTY.
OPERATor INSTRUCTIONS and parts SRT Model 7055C SRT Motor Mount PARTS 53638 53649 1423(4) WF516 (4) 60501 2104 1408 WF516(2) 739 53682 48144B 53622 53617 53637 WF516 504 810 WF516 2104 1408 WF516 802(2) 504(2) 1407(2) 1501 53633 810 504(2) WF516 743 803 731 804 742 739 WF516 48144B 1416 1418 53696B 53413 1501(4) 53623 53642(4) 60G56(5) WF516(2) 2104(2) 1501(4) 53648 60G56(4) Page 22 800-345-6007 GetEarthquake.
OPERATor INSTRUCTIONS and parts SRT Model 7055C SRT Motor Mount PARTS LIST PART # DESCRIPTION 1407 Forward Arm Spring 1408 QTY. PART # DESCRIPTION QTY. 2 60501 Engine, 6 hp Briggs & Stratton 1 Forward Pulley Idler 2 60G56 Nut Bi-Way Lock 5/16-18 5 1416 Clevis Pin 1 731 Two Groove Pulley 3/4” 1 1418 Cotter Pin 5/64” x 1/2” 1 739 Reverse Belt Guide 2 1423 Bolt 5/16-18 x 2” 4 742 Drive Pulley Spacer, .
OPERATor INSTRUCTIONS and parts SRT Model 7055C SRT Tines & Hood parts 417(2) 415A 504(2) 417(2) 1504(2) 1501(4) 69170 53660 1501(2) 1500P101(3) 1500P102 1500P103 2001(2) 1900RCRT 1900LCRT 1101A 719(2) 2104(2) 1103(2) 1501 1500P116(2) 1500P115 1500P115* 1101A 1500P103 1500P119 1500P120 48406 53640 1500P101(3) 7401 804 805 803 * Case only. Complete Tranny: 1500P1 504 802 727A 730 Page 24 800-345-6007 GetEarthquake.
OPERATor INSTRUCTIONS and parts SRT Model 7055C SRT Tines & Hood parts list PART # DESCRIPTION 1103 Lock Pin 5/16” x 1-3/4” 1500P115 QTY.
OPERATor INSTRUCTIONS and parts SRT Model 7055C SRT Wheel & Tiller Shaft PARTS & pARTS LIST 1500P104 1500P105 1500P110 1500P109 1500P108 1500P107 1500P108 1500P113 1500P112 1500P114 1500P110 1500P109 1500P108 1500P108 1500P107 1500P110 1500P109 1500P108 1500P107 1500P108 1500P106 1500P113 1500P117 1500P118 1500P105 1500P108 1500P107 1500P108 1500P107 1500P108 1500P109 1500P110 part # Description QTY. part # Description QTY.
SRT ROTOTILLERS 1-YEAR Limited Warranty Terms and Conditions Ardisam, Inc., a manufacturing company, warrants this Earthquake® SRT ROTOTILLER to be free from defects in the material or workmanship for a period of one year from the date of purchase. During the one-year warranty of this product, Ardisam will, at their discretion, furnish parts and labor to correct any defect caused by faulty material or workmanship.
Visit www.ardisam.com and discover more innovations that will benefit you throughout the year. Earthquake, Division of Ardisam, Inc. 1160 Eighth Avenue; P.O. Box 666 Cumberland, Wisconsin 54829 800-345-6007 · Fax (715) 822-4180 E-mail: info@ardisam.com GetEarthquake.
