TABLE OF CONTENTS About Earthquake Sound... Safety Instruction: Unpacking Tip: Introduction. ‘What Makes A Mini Me DSP 15 Amplifier Plate Placing Your Subprofessional} Connecting Your Sub woofers. Room Tuning With iWoofer™ App. Dimensions And Specifications. Warranty Information. For Your Records. levels. You should exercise caution when operating these speakers. Long term exposure to high levels of sound pressure will cause permanent damage to your hearing.
FOR YOUR RECORDS Date of Purchase: Authorized Dealer/ Installer Info: Address: Phone: Serial Number: Notes: 22 Specifications are subject to change without enigmatic ABOUT EARTHQUAKE SOUND For over 30 years, Earthquake Sound has been producing a variety of high quality audio products that have impressed audiophile communities around the world.
SAFETY INSTRUCTIONS SAFETY FIRST This document contains general safety, installation, and operating instructions for the Mini Me DSP sub woofer. It is important to read this user's manual before attempting to use this product. Pay particular attention to the safety instructions.
WARRANTY INFORMATION 5 YEAR LI BAITED WARRANTY INFORMATION Earthquake Sound warrants the original purchaser that all Factory Sealed New Audio products be free from defects in material and workmanship, under normal and proper use, for a period of Bee (5) year from the date of purchase {as shown on the original sales receipt with serial number affixed /written on it}.
SAFE AND PROPER HANDLING CONT'D = When carrying the Mini Me DSP, make sure that the speakers /grilles are positioned away from your chest, eliminating the chance of pushing against the face of the speaker. =» Do not drop the Minim E DSP or subject it to sudden shocks. This will damage the external finish and weaken the enclosure, creating air leaks. « Avoid exposing the Mini Me DSP to moisture, Water will damage the wood struck true as well as the amplifier and speaker.
DIMENSIONS AND SPECIFICATIONS MINIM DSP P-15 17.6" (448mm) 18" (458mm) 21.
AMPLIFIER PLATE OVERVIEW (1) Low Level RCA Input Use this input to deliver en audio signal rom your AV source to the Mini Me DSP 15 amplifier (2) Mono DSP Output Use this RCA output to deliver signal to an additional powered sub woofer or amplifier. (3) Balanced XLR Input Earthquake highly recommends using the fully balanced XLR input when the distance between the Mini Me DSP 15 and the audio source is excessive and susceptible to noise interference.
ROOM TUNING WITH i Woofer” Main Menu Cont'd ro a Hi Ste FE Hee Ba San Over Control ‘The X Over or Crossover control allows the user to control both the Low Pass and High Pass filters by double tapping the curve, or pressing and holding it for more than 1 second. The curve can then be slid left to right to control the frequency from 20Hz up to 500Hz. The curve can also be slid up and down to control the order of the filter up to an 8th order or 48 doctor filter.
PLACING YOUR SUBPROFESSIONAL) You often hear the term “sub woofers are non-directional” This is not true. It is harder to choose sub woofer placement when low frequencies are crossed. The wider the room, the more directional the sub woofer, The easiest solution is to use two (2) sub woofers, feed a mono signal to both and place them in front, one on the left and another on the right.
BALANCED XLR SETUP DUAL SUBS The diagram below illustrates how to connect two Mini Me DSP 15 sub woofers using only balanced XI.R cables. Use the MONO DSP output to connect one Mini Me DSP to an additional Mini Me DSP sub woofer or any other sub that supports an XLR input. XLR OUTPUTS FROM SOURCE 14 Specifications are subject to change without notice PLACING YOUR SUBPROFESSIONAL) DUAL SUB SETUP WITH MONO SIGNAL This is a BETTER setup.
LOW LEVEL SETUP DUAL SUBS For a more realistic sound stage and greater theater experience, we suggest having two (2) sub woofers and running them in stereo. Using a “Y” RCA cable, connect the SUB PRE OUT 1 of the receiver to the LOW LEVEL INPUT of the left side Mini Me DSP15. BACK OF TYPICAL A/V RECEIVER OR PROCESSOR Using another “Y" RCA cable, connect the SUB PRE OUT 1 of the receiver to the LOW LEVEL INPUT of the right side Mini Me DSP 15.
