DJ-ARRAY GEN2 LINE ARRAY SPEAKER SYSTEM OWNER’S MANUAL Earthquake Sound Corp. | (510) 732-1000 | www.earthquakesound.
TABLE OF CONTENTS About Earthquake Sound Corporation .......................... 3 Introduction....................................................................... 4 Safety Instructions ............................................................ 5 Assembling DJ-Array GEN2 .............................................. 6-7 Connecting DJ-Array GEN2............................................... 8 Specifications.....................................................................
ABOUT EARTHQUAKE SOUND CORPORATION For over 30 years, Earthquake Sound has been producing a variety of high quality audio products that have impressed audiophile communities around the world. It all started in 1984 when Joseph Sahyoun, a music freak and Aerospace Engineer unhappy with the existing loud speaker technology and performance, decided to put his advance engineering knowledge to use. He pushed technological boundaries to the limit to create the kind of subwoofer he could live with.
INTRODUCTION The DJ-Array GEN2 line array speaker system consists of two 4x4-inch array speakers that were designed for DJ and pro sound applications or where sound reinforcement is needed. The complete DJ-Array GEN2 System consists of the following packaged items: In The Box • • • • 4 Two (2) sets of 4 x 4” Array Speakers Two (2) 33 feet (10m) 1/4” TRS Speaker Cables Six Two (2) Metal Mounting Brackets Mounting Hardware DJ-Array GEN2 Manual Earthquake Sound Corp. | (510) 732-1000 | www.
SAFETY INSTRUCTIONS Safety First This documentation contains general safety, installation, and operating instruction for the DJArray Gen2 speaker system. It is important to read this owner’s manual before attempting to use this product. Pay particular attention to the safety instructions. Symbols Explained: Appears on the component to indicate the presence of uninsulated, dangerous voltage inside the enclosure - that may be sufficient to constitute a risk of shock.
ASSEMBLING DJ-ARRAY GEN2 SPEAKERS Before you begin assembling the DJ-Array GEN2 speaker system, make sure that you have all of the required mounting hardware. Each array requires 12 bolts and four nuts for assembly. 1. With the included mounting hardware, fasten the 35mm speaker stand bracket to the main speaker mounting bracket with a 3/16 hex key allen wrench (not included). Slide the brackets together as shown in the images to the right and use four of the nuts and bolts to secure them together.
ASSEMBLING DJ-ARRAY GEN2 SPEAKERS CONT. 2. With the mounting brackets assembled, begin mounting the array speakers with the remaining mounting hardware. Each of the four array speakers will require two bolts to securely fasten them to the mounting bracket. Align the speaker contacts with the mounting bracket contacts and gently push the speaker into place. Secure the array speaker with the two bolts and be careful not to over tighten them. Doing so could strip the threads inside the speaker.
CONNECTING DJ-ARRAY GEN2 SPEAKERS The DJ-Array GEN2 speakers are equipped with 1/4″ TRS input connectors at the bottom portion of the mounting bracket. With the supplied TRS cables, gently push one end of the TRS cable plug into the input as shown below and push the other end into your amplifier or powered subwoofer.
SPECIFICATIONS DJ-ARRAY GEN2 Power Handling RMS Power Handling MAX Impedance 50 Watts Per Channel 100 Watts Per Channel 4-Ohm Sensitivity 98dB (1w/1m) High Pass Filter 12dB/oct @ 120Hz–20kHz Array Components 4″ Midrange 1″ Compression Driver Input Connectors 1/4″ TRS Net Weight (1 Array) 20 lbs (18.2 kgs) 11.5ʺ (292mm) 26ʺ (660mm) 5.75ʺ (146mm) Specifications are subject to change without notice.
ONE (1) YEAR LIMITED WARRANTY GUIDELINES Earthquake warrants the original purchaser that all Factory Sealed New Audio Products to be free from defects in material and workmanship under normal and proper use for a period of one (1) years from the date of purchase (as shown on the original sales receipt with serial number affixed/written on it).
FOR YOUR RECORDS Model Name/Number: Serial Number: ___________________________________________________ ____________________________________________________________ Date of Purchase: _________________________________________________________ Authorized Dealer/Installer Info: Name: ______________________________________________________________________ Address: ____________________________________________________________________ ____________________________________________________________________ Phone:
Earthquake Sound Corporation 2727 McCone Avenue. Hayward CA, 94545. USA US Toll Free: 800-576-7944 | Phone: 510-732-1000 | Fax: 510-732-1095 www.earthquakesound.com | www.earthquakesoundshop.
