Installation Guide

PREMIUM COAT
USES
Seals, protects, and adds gloss to exposed aggregate concrete.
 CLEAR for use on all types of exposed aggregate concrete and concrete pavers.
 BROWN TINTED for use on exposed pea gravel concrete
 GRAY TINTED for use on exposed gray chipped limestone concrete
DESCRIPTION
EAGLE PREMIUM COAT is a premium solvent-based concrete sealer specifically formulated for exposed aggregate concrete.
This high solids, styrene-acrylic copolymer solution is formulated to achieve both a protective and decorative finish. Along with protecting
concrete surfaces against water seepage and aggregate loosening, EAGLE PREMIUM COAT beautifies the surface with a high gloss
finish that shines and darkens as it protects.
TOOLS & MATERIALS REQUIRED
 EAGLE CLEANER DEGREASER & NEUTRALIZER
 EAGLE ETCH & CLEAN
 Solvent resistant roller
 Eye protection & Gloves
SURFACE PREPARATION
Clean dirt, wax, grease, oil and other contaminants from the surface. Be sure to remove any foreign coating unless previous
coating is same or similar solvent-based sealer. Make sure the surface is clean, dry and sound. Clean oily concrete with EAGLE
CLEANER DEGREASER & NEUTRALIZER. Use a bristle brush for heavily oiled spots. If surface is unsealed and slick, etch with
EAGLE ETCH & CLEAN. Rinse well with a pressure washer. Allow 24 hours to dry. Apply only when surface and air temperatures are
above 50° F and below 90° F. Do not apply to excessively hot surfaces as rapid drying may cause bubbles or streaking to form.
APPLICATION
For exterior application, only. Perform test to ensure compatibility. Brush may be used where roller won’t reach. Do not pour
directly from can to concrete. Apply evenly from can or other metal container with solvent resistant long nap roller. Keep roller soaked.
Wait until the surface is tack-free before applying a second coat by cross-rolling perpendicular to the first coat. Do not thin product. Foot
traffic should be avoided for 4 hours. Vehicle traffic should be avoided for 48 hours. Do not apply if rain is imminent. Cooler temperatures
or increased humidity will slow the drying time.
NET COVERAGE RATE
Two thin coats are recommended yielding the following net coverage.
Exposed Aggregate Concrete: 100 ft² per gallon
Concrete Pavers 75 ft² per gallon
CLEANUP
Clean up tools with Xylene, Toluene or Lacquer Thinner. Do not use Paint Thinner, Mineral Spirits or water.
MAINTENANCE
Clean sealed surface with water only. High gloss sheen will diminish over time, especially in direct sunlight. Reseal surface as
needed, but no more often than every two years to prevent buildup of sealer.
WARNING
COMBUSTIBLE. EYE, SKIN & RESPIRATORY IRRITANT. Contains Aromatic Naptha. Do not use near heat, sparks or open
flames. Avoid contact with eyes and prolonged contact with skin. Use only with adequate ventilation. Do not inhale vapors. Do not
ingest. See Safety Data Sheet for more info.
FIRST AID
In case of eye contact, flush with water for 15 minutes. In case of skin contact, wash thoroughly with soap and water. If swallowed,
do not induce vomiting. Immediately contact hospital ER or physician. If vapors are inhaled or breathing becomes difficult, move person
to fresh air. Seek medical attention if skin, eye or respiratory irritation persist. See Safety Data Sheet for more info.
TECHNICAL DATA
VOC: <700 g/L Flash Point: 105 F
Meets or exceeds specification ASTM C1315
DISCLAIMER: Since manufacturer has no control over handling, use or storage; no guarantee expressed or implied, is offered. Eagle IFP warrants the product to be free of defects and will replace
or refund the purchase price of said products proven defective. Labor cost and/or other consequential damages are not covered by this warranty. Responsibility for claims of any kind is strictly limited to
the purchase price of the product. The suitability of the product for any extended use shall be solely up to the user.
Made in U.S.A
EAGLE IFP COMPANY
www.eaglesealer.com