User Manual

ManualsBrandsEagle Tree Systems LLC ManualsHobbySeagull Wireless Dashboard Flight System: 2.4 Ghz

Page 24

Code 3, EVENT_INITIALIZE_FAILED - internal,

Code 4, EVENT_CANT_SEND_HEADER - internal,

Code 5, EVENT_CANT_SEND_ANALOG_PACKET - internal,

Code 6, EVENT_CANT_SEND_DATA_PACKET - internal,

Code 7, EVENT_BATTERY_LOW – battery has fallen below a safe level for an extended period of time,

Code 8, EVENT_BATTERY_DEAD – not used

Code 9, EVENT_RESTART – the recorder has been restarted normally,

Code 10, EVENT_NESTED_INT_DISABLE - internal,

Code 11, EVENT_ILLEGAL_INT - internal,

Code 12, EVENT_LOW_BAT_RESTART – the recorder has been restarted due to a brownout, generally less

than 4.4V

Code 13, EVENT_SERVO_GLITCH_MISSED – a servo pulse was missing,

Code 14, EVENT_SERVO_GLITCH_SHORT – a servo pulse was shorter than 740uSec,

Code 15, EVENT_SERVO_GLITCH_LONG – a servo pulse was longer than 2.25mSec,

Code 16, EVENT_TX_INIT – this indicates that the Seagull Transmitter was initialized,

Code 17, EVENT_THIS_PACKET_DUPED – this indicates that the packet is a duplicate of the prior packet

(wireless only),

Code 18, EVENT_GPS_DATA_PACKET – indicates that GPS data was freshly received with this packet,

Code 19, EVENT_GPS_WRONG_MESSAGE – internal,

Code 20, EVENT_GPS_DATA_INVALID - internal,

Code 21, EVENT_GPS_DATA_LOST - internal,

Code 22, EVENT_ALT_AIR_READ_FAILED - internal,

Code 23, EVENT_USB_CONNECTED – internal,

Code 24, EVENT_ECU_DATA_PACKET – indicates that ECU data was received,

Code 25, EVENT_ECU_WRONG_MESSAGE - internal,

Code 26, EVENT_NIMU_DATA_PACKET – indicates that an IMU packet was received,

Code 27, EVENT_SPEKTRUM_DATA_PACKET – indicates that Spektrum FlightLog data was received

Email us if you need more information on the file format.

Troubleshooting

Below is a list of problems that may be encountered, and steps to remedy them. If your particular issue is not addressed

by the below, see the Support page at

http://www.eagletreesystems.com/Support/support.html.

Issue: My model’s altitude reading does not appear to be correct.

Solution: If your model is not airtight or at least sealed well up front, you may have altitude jumpiness, since the

altimeter measures changes in air pressure. Install the T fitting as described in the “Altitude Measurement” section

above.

Issue: I get the “No Signal” message from the Dashboard, and never see live data.

Solution: Make sure the Seagull Transmitter is plugged into the correct Recorder slot, and that the plug polarity is correct

Solution: Make sure that the Recorder light is flashing one repeated flash (or two repeated flashes if the Recorder buffer

is full)

Solution: Make sure that the Recorder is not connected to USB.

Solution: Turn vehicle’s power off, WAIT 10 SECONDS, turn your vehicle’s power back on, and then turn your

Dashboard off and on.

Solution: Make sure the Seagull ID is correctly set in both the Recorder and the Dashboard, by running through the

Seagull Setup Wizard again.

Solution: Make sure you have chosen a Recorder sampling rate that is Seagull compatible. This is set in the software by

choosing “Tools, Choose Capture Rate” with the Recorder connected. 10 Samples/Second is recommended.

Issue: My Dashboard is receiving data, but it doesn’t look like correct data.

Solution: Some parameters, like altitude, airspeed and current, are “zero calibrated” each time the Dashboard is turned on.

If these parameters are not zeroed, try turning off and on the Dashboard.

Issue: My altitude or airspeed values seem to drift, even when the vehicle is sitting still.