Datasheet

Irrtümer und Änderungen vorbehalten / Subject to modication without notice, errors and omissions excepted
Alle Wertangaben sind typische Werte / All values are typical values
Datum / Date: 17.01.12
EA-PSI 8000 3U HS PV 10KW & 15KW
DC-NETZGERÄTER PHOTOVOLTAIK / DC POWER SUPPLIES FOR PHOTOVOLTAICS
DCoutput
Output voltages of 0...600V, 0...1000V or 0...1500V, output
currents of 0...30A or 0...70A and fully adjustable output power
ratings 10kW or 15kW are available. The output terminal is
located in the rear panel.
Overvoltageprotection(OVP)
Intended to protect connected loads, it is possible to dene
an overvoltage protection limit (OVP).
If the output voltage exceeds the dened limit, the output
is shut-off and an acoustic warning signal will be given by
the unit and also a status message signal in the display is
available.
Expandability
Upon request, single units can be combined into various
congurations in cabinets of up to 42U and up to 150kW total
power in parallel connection.
Built-in,isolatedanalogueInterface
The built-in analogue interface terminal is located on the rear
of the device and offers galvanic isolation of up to 1500V DC.
This provides the possibility to even work with transformerless
solar inverters on the DC output.
There are analogue inputs to set voltage, current and power
from 0...100% by feeding control voltages of 0V...10V or
0V...5V.
To monitor the output voltage and current, there are analogue
outputs with voltage ranges of 0V...10V or 0V...5V. Also,
several inputs and outputs are available for controlling and
monitoring the device status.
Options
Isolated digital interface cards for RS232, CAN, USB, GPIB
(IEEE) or Ethernet/LAN to control the device by PC. Included
with the interface cards is a free Windows software which
provides control and monitoring, data logging and sequences.
Isolated analogue interface card with extended features
Rearview
Rückansicht
448mm
129mm
Einschub für dig.Schnittstellen
Slot for digital interfaces
Anschluß Parallelschaltung & Sense
Terminals for parallel connection & sense
Analogschnittstelle
Analogue interface
Ausgang
Zur Verfügung stehen Geräte mit Ausgangsspannungen von
0...600V, 0...1000V oder 0...1500V, Strömen von 0...30A oder
0...70A und von 0...100% regelbaren Leistungen von 10kW
oder 15kW. Der Ausgang bendet sich auf der Rückseite
der Geräte.
Überspannungsschutz(OVP)
Um die angeschlossenen Verbraucher vor Zerstörung zu
schützen kann ein Überspannungsschutz (OVP) eingestellt
werden. Beim Überschreiten des eingestellten Wertes wird
der Ausgang abgeschaltet und es wird eine Warnmeldung als
akustisches Signal und als Statusmeldung auf der analogen
Schnittstelle und im Display ausgegeben.
Erweiterbarkeit
Die Einzelgeräte können in verschiedenen Kombinationen,
auch in Schränken bis 42HE und bis zu 150kW, nach Kun-
denwünschen konguriert werden.
Eingebaute,isolierteAnalogschnittstelle
Eine Analogschnittstelle bendet sich auf der Rückseite des
Gerätes ist bis 1500V DC galvanisch getrennt. Damit kann
das Gerät bei Betrieb an trafolosen Wechselnrichtern fern-
gesteuert werden.
Sie verfügt über analoge Steuereingänge für 0...10V oder
0...5V um Spannung, Strom und Leistung von 0...100% zu
programmieren.
Ausgangsspannung und Ausgangsstrom können über analo-
ge Monitorausgänge mit 0...10V oder 0...5V ausgelesen wer-
den. Weiterhin gibt es einige Statuseingänge und -ausgänge.
Optionen
Digitale, galvanisch getrennte Schnittstellenkarten für
RS232, CAN, USB, GPIB (IEEE), Probus oder Ethernet/
LAN zur Steuerung per PC. Dazu gibt es eine freie Win
-
dows-Software, die Datenaufzeichnung und automatisiertes
Steuern ermöglicht.
Galvanisch getrennte, analoge Schnittstellenkarte