Manual

© EA Elektro-Automatik in 2022, this information is subject to change without notice 233200840_manual_elr_10000_2u_3kw_en_02
TABLE OF CONTENTS
1. General
1.1 About this document 5
1.1.1 Retention and use 5
1.1.2 Copyright 5
1.1.3 Validity 5
1.1.4 Symbols and warnings in this document 5
1.2 Warranty 5
1.3 Limitation of liability 5
1.4 Disposal of equipment 6
1.5 Product key 6
1.6 Intended usage 7
1.6.1 Symbols and warnings on the device 7
1.7 Safety 8
1.7.1 Safety notices 8
1.7.2 Responsibility of the operator 9
1.7.3 Requirements to the user 9
1.7.4 Responsibility of the user 9
1.7.5 Alarm signals 10
1.7.6 Functionality test 10
1.8 Technical Data 11
1.8.1 Approved operating conditions 11
1.8.2 General technical data 11
1.8.3 Specific technical data 12
1.8.4 Views 16
1.8.5 Control elements 18
1.9 Construction and function 19
1.9.1 General description 19
1.9.2 Block diagram 19
1.9.3 Scope of delivery 20
1.9.4 Accessories 20
1.9.5 Options 20
1.9.6 The control panel (HMI) 21
1.9.7 USB port (rear side) 24
1.9.8 Interface module slot 24
1.9.9 Analog interface 25
1.9.10 “Share BUS” connector 25
1.9.11 “Sense” connector (remote sensing) 25
1.9.12 Master-Slave bus 26
1.9.13 Ethernet port 26
2. Installation & commissioning
2.1 Transport and storage 27
2.1.1 Transport 27
2.1.2 Packaging 27
2.1.3 Storage 27
2.2 Unpacking and visual check 27
2.3 Installation 27
2.3.1 Safety procedures before installation and use 27
2.3.2 Preparation 27
2.3.3 Installing the device 29
2.3.4 Connection to AC supply 30
2.3.5 Connection to DC sources 32
2.3.6 Connection of remote sensing 33
2.3.7 Grounding of the DC terminal 33
2.3.8 Installation of an interface module 34
2.3.9 Connection of the analog interface 35
2.3.10 Connection of the Share bus 35
2.3.11 Connection of the USB port (rear side) 35
2.3.12 Initial commission 35
2.3.13 Commission after a firmware update or a long
period of non-use 35
3. Operation and application
3.1 Important notes 36
3.1.1 Personal safety 36
3.1.2 General 36
3.2 Operating modes 36
3.2.1 Voltage regulation / Constant voltage 36
3.2.2 Current regulation / constant current / current
limiting 37
3.2.3 Power regulation / constant power / power
limiting 37
3.2.4 Resistance regulation / constant resistance 37
3.2.5 Dynamic characteristics and stability criteria 37
3.3 Alarm conditions 38
3.3.1 Power Fail 38
3.3.2 Overtemperature 38
3.3.3 Overvoltage protection 38
3.3.4 Overcurrent protection 38
3.3.5 Overpower protection 38
3.3.6 Share bus fail 39
3.4 Manual operation 40
3.4.1 Switching on the device 40
3.4.2 Switching the device off 40
3.4.3 Configuration via the menu 40
3.4.4 Adjustment limits 49
3.4.5 Changing the operating mode 49
3.4.6 Manual adjustment of set values 50
3.4.7 Switching the DC input on or off 51
3.4.8 Recording to USB stick (logging) 51
3.4.9 The quick menu 52
3.4.10 The graph 53
3.5 Remote control 54
3.5.1 General 54
3.5.2 Control locations 54